FaultResolve
返回搜尋目錄
Search this section

Search Fanuc R-30i Series Robot Controller

Search other Fanuc R-30i Series Robot Controller alarms without going back to the model list.

Search all database

代碼 CVIS-456: This camera is not supported.

問題描述與安全警告

Fanuc R-30i Series Robot Controller 觸發了嚴重的 This camera is not supported. 警報。需要由合格的操作員或維修技師立即處理,以防止在製造週期中對設備造成二次損壞或導致零件報廢。在接觸電氣控制箱之前,請務必確保遵循標準安全和停機掛牌 (LOTO) 程序。

官方故障排除步驟

Cause: This camera is not supported. Remedy: Change camera. CVIS-457: A 2-D Barcode could not be found in the image. Cause: A 2-D Barcode could not be found in the image. Remedy: View the binary image on the setup page to verify that the threshold is correct. Check the search window on the setup page to verify that the 2-D Barcode is within the window. CVIS-458: The 2-D Barcode geometry is bad. Cause: The 2-D Barcode geometry is bad. Remedy: View the binary image on the setup page to verify that the threshold is correct. Check the search window on the setup page to verify that the 2-D Barcode is within the window. For Data Matrix code, verify that the 2-D Barcode has an even number of rows and columns. Verify that the 2-D Barcode is not damaged. CVIS-459: The 2-D Barcode is too damaged to read. Cause: The 2-D Barcode is too damaged to read. Remedy: For Data Matrix code, view the binary image on the setup page to verify that the threshold is correct. Check the search window on the setup page to verify that the 2-D Barcode is within the window. Verify that the 2-D Barcode is not damaged. CVIS-460: 2-D Barcode reader internal software error. Cause: Internal error. Remedy: Contact your local FANUC representative. CVIS-461: Illegal character found in 2-D Barcode. Cause: An illegal text character was found in the 2-D Barcode. Remedy: Verify that the 2-D Barcode is not damaged. CVIS-462: The 2-D Barcode reader does not support Base 256 encoding. Cause: The 2-D Barcode contains an unsupported feature. Remedy: None. CVIS-463: The 2-D Barcode reader does not support FNC1 alternate data types. Cause: The 2-D Barcode contains an unsupported feature. Remedy: None. CVIS-464: The 2-D Barcode reader does not support Structured Append sequences. Cause: The 2-D Barcode contains an unsupported feature. Remedy: None. CVIS-465: The 2-D Barcode reader does not support Reader Programming. Cause: The 2-D Barcode contains an unsupported feature. Remedy: None. CVIS-466: The 2-D Barcode reader does not support Upper Shift to Extended ASCII characters. Cause: The 2-D Barcode contains an unsupported feature. Remedy: None. CVIS-467: The 2-D Barcode reader does not support 05 Macros. Cause: The 2-D Barcode contains an unsupported feature. Remedy: None. CVIS-468: The 2-D Barcode reader does not support 06 Macros. Cause: The 2-D Barcode contains an unsupported feature. Remedy: None. CVIS-469: The 2-D Barcode reader does not support ANSI X12 encoding. Cause: The 2-D Barcode contains an unsupported feature. Remedy: None. CVIS-470: The 2-D Barcode reader does not support EDIFACT encoding. Cause: The 2-D Barcode contains an unsupported feature. Remedy: None. 4.ERROR CODES B-83124EN-6/02 CVIS-471: The 2-D Barcode reader does not support Extended Channel Interpretation (ECI). Cause: The 2-D Barcode contains an unsupported feature. Remedy: None.

Source: FANUC Robot R-30iA Alarm Code List Operator's Manual

Last reviewed: 2026-07-01 · Verified against the manufacturer’s official documentation.

關於 Fanuc R-30i Series Robot Controller 警報

由 Fanuc 製造的工業控制器具有廣泛的診斷系統,用於保護內部電路和機械連桿。當 R-30i Series Robot Controller 出現類似 CVIS-456 的錯誤代碼時,通常表示指令值與實際感測器回饋之間存在不匹配。

完整警報清單: 6553 Fanuc R-30i Series Robot Controller 代碼s.

Have a better solution?

Help the industrial community by sharing your repair experience for code CVIS-456.

Manual conversion service

Need a searchable reference for more Fanuc R-30i Series Robot Controller manuals?

We structure equipment manuals into searchable code, title, cause, solution, safety note, and source-reference data. Send a PDF and example searched codes when you need public pages, private search, or structured exports.

Convert PDF fault-code charts and manuals into clean data.
Build public SEO pages or private internal search tools.
Prioritize updates around codes and manuals people search for.
Request manual conversion Email PDFs to manuals.errordb@gmail.com
Advertisement

Space reserved for Google AdSense / Industrial Affiliate Links

Monetization target for 2026

相關的 Fanuc R-30i Series Robot Controller 代碼