Code SYST-223: Image backup failed(0x%x)
Problembeschreibung & Sicherheitswarnung
Die Fanuc R-30i Series Robot Controller hat einen kritischen Image backup failed(0x%x)-Alarm ausgelöst. Sofortige Aufmerksamkeit durch einen qualifizierten Bediener oder Wartungstechniker ist erforderlich, um Folgeschäden an der Ausrüstung oder verdorbene Teile während des Fertigungszyklus zu vermeiden. Stellen Sie immer sicher, dass standardmäßige Sicherheits- und LOTO-Verfahren befolgt werden, bevor Sie auf Schaltschränke zugreifen.
Offizielle Schritte zur Fehlerbehebung
Cause: Image backup failed. Remedy: 0x%x shows the cause of the failure. Find the definition in the list below. Remove the cause of the failure and try the backup again. z 0x%x Cause and remedy 0x1 This isn't used. 0x2 Memory allocation failed. Call your local FANUC representative. z 0x3 Information in FROM cannot be acquired. Call your local FANUC representative. z 0x4 Make sure there is enough free space on the MC. Make sure a FLASH ATA card is inserted in the MC card slot. z 0x5 Controller could not open FROM***.IMG. Destination device might be broken. z 0x6 Controller could not read FROM. FROM module or main board FROM might be broken. z 0x7 Controller could not write data to FROM***.IMG. Destination device might be broken. z 0x8 Controller could not close FROM***.IMG. The following are possible causes: z There are already backup files on the destination device and they are write-protected. z MC was removed during backup. z Communication was disconnected during backup to TFTP server. z TFTP server is not running. z 0x9 Make sure there is enough free space on MC. Make sure FLASH ATA card is inserted to MC card slot. z 0xa Controller cannot open SRAM***.IMG. Destination device might be broken. z 0xb Controller could not write data to SRAM***.IMG. Destination device might be broken. z 0xc Controller could not close SRAM***.IMG. The following are possible causes: z There are already backup files on the destination device and they are write-protected. z MC was removed during backup. z Communication was disconnected during backup to TFTP server. z TFTP server is not running. z 0xd File for internal use may be broken. Try the backup again. z 0xe File for internal use may be broken. Try the backup again. z 0xf After power was cycled by image backup function, a backup file was found on the MC. This happens if power is turned off during automatic image backup. Retry backup from file screen again. z 0x20 Initialization of network failed. Confirm wiring and BOOTP server is running.
Source: FANUC Robot R-30iA Alarm Code List Operator's Manual
Last reviewed: 2026-07-01 · Verified against the manufacturer’s official documentation.
Über Fanuc R-30i Series Robot Controller Alarme
Industriesteuerungen von Fanuc verfügen über umfangreiche Diagnosesysteme zum Schutz der internen Schaltkreise und mechanischen Verbindungen. Wenn eine R-30i Series Robot Controller einen Fehlercode wie SYST-223 ausgibt, deutet dies typischerweise auf eine Diskrepanz zwischen befohlenen Werten und tatsächlichem Sensor-Feedback hin.
Vollständige Alarmliste: 6553 Fanuc R-30i Series Robot Controller codes.
Have a better solution?
Help the industrial community by sharing your repair experience for code SYST-223.
Need a searchable reference for more Fanuc R-30i Series Robot Controller manuals?
We structure equipment manuals into searchable code, title, cause, solution, safety note, and source-reference data. Send a PDF and example searched codes when you need public pages, private search, or structured exports.
Space reserved for Google AdSense / Industrial Affiliate Links
Monetization target for 2026