Back to all Heidenhain models

Heidenhain TNC Series CNC

Heidenhain TNC Series CNC Error Codes

Complete alarm and error code reference for the Heidenhain TNC Series CNC. Browse all 4497 documented fault codes below, each linking to a detailed troubleshooting guide.

Search this section

Search Heidenhain TNC Series CNC

Search all 4497 Heidenhain TNC Series CNC codes without changing pages.

Search all database

Complete Alarm List (Page 1 of 23)

Configuration of soft key not readable

Configuration of layer not readable

Cycle or query %1 unknown

Cannot generate menu

Q Parameter %1: Cannot read or write value

Soft-key group without first element

Soft-key type is not supported

Invalid resource ID

Invalid configuration data for cycle

Error in the user interface

Can't connect to network: %1 %2 %3

File '%1' not found

Unable to open configuration server queue

Unable to read configuration data '%1'

Path '%1' not found

No files available for online help (*.CHM)

Error when saving the screen content in the file %1

Source file %1 not found

Example file %1 could not be copied. Error code %2

List for copying the example files not available %1

Error during software update: %1

The update rules are not fulfilled

Update file invalid or does not exist

Checksum error during update

Invalid signature entry during update

Not enough memory. Update not possible.

Backup file not found

ZIP file contains no control setup

Unable to write configuration data '%1'

In the configuration data, no operating

The connection list is full

Connection setup to DNC not possible

TeleService request is in error

TeleService request is in error

Traverse limits were not adopted.

Input not in effect

Kinematic model was not switched over

Unit of measure was not switched

Error during self-test

Error during self-test

Error during self test

Self-test cannot be started

The CC only runs with 500 MHz

NC software not released for FS applications

Too many switch-off ports defined

Switch-off port on incorrect bus system

PLC output for shutdown has multiple definitions

Automatic switch-off not possible

PLC output for switch-off is improperly defined

PLC output for switch-off is improperly configured

PLC output for switch-off is improperly configured

PLC output for switch-off is improperly configured

Key name %1 for OEM script is too long

Hardware combination not permitted

Self-test error was not detected on %2 with HSCI address %3

No reaction during self-test on %2 with HSCI address %3

Self-test was not executed on %2 with HSCI address %3

Missing authorization

Safety not ensured

Safe configuration data %1 changed

Automatic switchover in simulation mode DriveSimul

Automatic switchover in simulation mode DriveAndEmS-

Automatic switchover in simulation mode FullSimul

Too many UM units connected to one CC: CC index %1

Component: %1 with serial number: %2 not planned in

Project planning with IOconfig incomplete

TNCdiag cannot be started

Too many HSCI devices connected. Current: %1; permitted:

Too many CC/UxC devices connected. Current: %1; permit-

Too many PLB/MB/TE/UxC devices connected. Current: %1;

Too many MB/TE devices connected. Current: %1; permitted:

Too many UVR devices connected. Current: %1; permitted:

Too many I/O terminals present. Current: %1; permitted: %2

The IOCP file for projecting the hardware was not loaded

Projected HSCI device could not be assigned

Projected module of HSCI device could not be assigned

Processor check error

File access was successful

File system error

Illegal file name

Too many files open

File access not possible

File access not possible

Directory could not be erased

Further file entry impossible

File access not possible

Drive not ready

File access not possible

File access not possible

Further file entry impossible

Program incomplete

Directory access not possible

Error: Unexpected end of process %1

ClientQueue (%1) could not be opened

Log file could not be saved.

ASSERTION: Consistency condition not fulfilled

Invalid event class in the following error!

OEM error without additional information

Cycle error without additional information

Saving service files...

The error log could not be opened. NOTE: No error

Error while saving the service file

Incorrect condition in switch statement

No acknowledgment from application %1

Configuration datum %1 - %2

Configuration datum %1 - %2

NC program cancelled

File exists already

File access not possible

Directory not found

Drive not found

Service files could not be saved

There is no online help for the error!

File not found: %1

Error when opening/closing a zip file (%1)

There was an error when saving a (zip) file

Key might be jammed

Parameter transfer not possible

No response from drive “%1”!

Program start or program selection has failed

The application cannot be started

Non-secure DNC connection %1 detected from %2

Non-secure connection %1 detected from %2

Backup copy of the configuration data cannot be created.

Configuration file '%1' cannot be written.

Configuration file '%1' not found.

Data object '%1' '%2' not complete

Key of the data object '%1' not initialized.

Cycle ini file '%1' not found.

Unknown code word '%1' in cycle ini file.

No text found for text name '%1'

Module '%1' not open.

Module '%1' has no general write access.

'%1' has no general write access.

Unknown message '%1' for configuration server.

Write access for '%1' '%2' not reserved.

Incorrect file type '%1' with '%2'.

Character string '%1' not found in '%2'.

ZERO message '%1'

Machine parameters were changed.

Data object '%1' '%2' already exists in file

Internal software error

Configuration object '%1' / '%2' not found

No change acknowledgment obtained from '%1'

Parameter change during program run or macro run

Parameter locked from editing

Program start: Data objects with write protection not allowed

Module name missing or unknown '%1'

Data object '%1' renamed to '%2'

Data object '%1' '%2' removed

Data type changed with data object '%1' '%2'

Attribute renamed in data object '%1' '%2'

Attribute in data object '%1' '%2' removed

Attribute inserted in data object '%1' '%2'

Data object '%1' '%2' removed

Data object '%1' '%2' inserted

Incorrect insertion value in data object '%1' '%2'

Data file not saved

Unknown object name '%1'

Maximum list size exceeded

SIK control identification faulty: %1

General key expired

General key is active

'%1' entered as password

Incorrect software version

1-200 of 4497