コード 606-03A0: Finished part no longer located within
問題の説明と安全警告
Heidenhain TNC Series CNC は重大な Finished part no longer located within アラームをトリガーしました。製造サイクル中に機器への二次的損傷や部品の破損を防ぐために、資格のあるオペレーターまたはメンテナンス技術者による直ちの対応が必要です。電気キャビネットにアクセスする前に、必ず標準の安全およびLOTO手順が遵守されていることを確認してください。
公式トラブルシューティング手順
%1 [Cause of error] The cycle requires a greater safety clearance in order to work without collision. [Error correction] Program a greater safety clearance. [60C-000B] [Cause of error] The cycle cannot be run with the entered values. [Error correction] - Correct the values - Restart the program [60C-000C] [Cause of error] The cycle cannot be run with the entered values. [Error correction] - Correct the values - Restart the program [60C-000D] [Cause of error] The cycle cannot be run with the entered values. [Error correction] - Correct the values - Restart the program [60C-000E] [Cause of error] The cycle cannot be run with the entered values. [Error correction] - Correct the values - Restart the program 10/2023 [1243] [60C-000F] [Cause of error] The cycle cannot be run with the entered values. [Error correction] - Correct the values - Restart the program [60C-0010] [Cause of error] The cycle cannot be run with the entered values. [Error correction] - Correct the values - Restart the program [60C-0011] [Cause of error] The cycle cannot be run with the entered values. [Error correction] - Correct the values - Restart the program [60C-0012] [Cause of error] The cycle cannot be run with the entered values. [Error correction] - Correct the values - Restart the program [60C-0013] [Cause of error] The cycle cannot be run with the entered values. [Error correction] - Correct the values - Restart the program [1244] 10/2023 [60C-0014] [Cause of error] The cycle cannot be run with the entered values. [Error correction] - Correct the values - Restart the program [60C-0015] Actual: %2 Nominal: %3 [Cause of error] The cycle cannot be run with the entered values. [Error correction] - Correct the values - Restart the program [60C-0016] [Cause of error] Automatic calculation of the infeed depths and feed rates is not possible. [Error correction] Vary the number of cuts or set the value to 0 (automatic calculation of the number of cuts) [60F-0033] current workpiece. %1 [Cause of error] An area of the finished part, e.g. an end point, lies outside of the defined workpiece blank. This note has no effect on the program run. [Error correction]
Source: HEIDENHAIN NC Error Messages — TNC7/640/620/320/128, CNC PILOT 640, MANUALplus 620 (10/2023)
Last reviewed: 2026-07-01 · Verified against the manufacturer’s official documentation.
Heidenhain TNC Series CNC のアラームについて
Heidenhain によって構築された産業用コントローラーは、内部回路と機械的リンケージを保護するための広範な診断システムで設計されています。TNC Series CNC が 606-03A0 のようなエラーコードをスローする場合、通常、指令値と実際のセンサーフィードバック間の不一致を示します。
完全アラーム一覧: 4497 Heidenhain TNC Series CNC コードs.
Have a better solution?
Help the industrial community by sharing your repair experience for code 606-03A0.
Need a searchable reference for more Heidenhain TNC Series CNC manuals?
We structure equipment manuals into searchable code, title, cause, solution, safety note, and source-reference data. Send a PDF and example searched codes when you need public pages, private search, or structured exports.
Space reserved for Google AdSense / Industrial Affiliate Links
Monetization target for 2026