Heidenhain の全機種へ戻る Search all database
Heidenhain TNC Series CNC
Heidenhain TNC Series CNC エラーコード
Heidenhain TNC Series CNC の完全なアラーム・エラーコードリファレンス。以下に全 4497 件の故障コードを掲載し、各コードから詳細なトラブルシューティングガイドへ移動できます。
Search this section
Search Heidenhain TNC Series CNC
Search all 4497 Heidenhain TNC Series CNC codes without changing pages.
完全アラーム一覧 (Page 7 of 23)
コード 230-047B
Programmed position error too large. Limit to %1 mm.
解決方法を見る コード 230-047E
Axis %2: Double reference name is active
解決方法を見る コード 230-047F
Current actual position of the axis (%2) cannot be used
解決方法を見る コード 230-0480
Max. compensation value %2 reached in axis %1
解決方法を見る コード 230-0481
Handwheel %3: Wrong handwheel connected
解決方法を見る コード 230-0482
Handwheel %3: Contaminated or damaged
解決方法を見る コード 230-0483
Handwheel %3: Transmission disturbance
解決方法を見る コード 230-0484
Handwheel %3: Transmission error
解決方法を見る コード 230-0485
Handwheel %3: Wrong parameter
解決方法を見る コード 230-0486
Handwheel %3: Timeout
解決方法を見る コード 230-0487
Handwheel %3: No connection possible
解決方法を見る コード 230-0488
No assignment between handwheels and connections
解決方法を見る コード 230-0489
Only one HR 550FS wireless handwheel possible
解決方法を見る コード 230-048C
Error in acknowledging the SampleRate of the CC
解決方法を見る コード 230-048D
Handwheel superimpositioning is ignored
解決方法を見る コード 230-048E
Internal software error during Program Run, Single Block
解決方法を見る コード 230-048F
Handwheel %3: Communication error
解決方法を見る コード 230-0490
PLC movement for axis %2 was canceled
解決方法を見る コード 230-0491
Retraction from thread completed
解決方法を見る コード 230-0492
NC software does not match UVR firmware
解決方法を見る コード 230-0493
MCU/UVR watchdog mismatch
解決方法を見る コード 230-0494
Message from UVR %2
解決方法を見る コード 230-0495
Incorrect axis index in axis %1
解決方法を見る コード 230-0496
Input for speed encoder (%1) not valid
解決方法を見る コード 230-0497
Incorrect inverter or motor connection (%1, inv. %2, motor
解決方法を見る コード 230-0498
Faulty synchronization during a movement
解決方法を見る コード 230-0499
CfgLaAxis/MP_axManualJerk (%2) missing for interpol. PLC
解決方法を見る コード 230-049A
Spindle speed?
解決方法を見る コード 230-049C
Timeout during command processing by the UVR %2
解決方法を見る コード 230-049D
A parameter change requires switching off the drive
解決方法を見る コード 230-049E
Real time coupling function (RTC) together with handwheel
解決方法を見る コード 230-04A0
Test of brake %1 for axis %2 was unsuccessful
解決方法を見る コード 230-04A2
Touch probe %1 is not supported by the transmitter/receiver
解決方法を見る コード 230-04A3
Collision of the touch probe
解決方法を見る コード 230-04A4
Configuration of handwheel on axis %2 is faulty
解決方法を見る コード 230-04A5
Handwheel %3: Handwheel is not supported
解決方法を見る コード 230-04A6
Multiple handwheels on the same radio channel
解決方法を見る コード 230-04A7
Other radio devices are disturbing radio handwheel operation
解決方法を見る コード 230-04A8
Could not activate or deactivate axis %2
解決方法を見る コード 230-04A9
Do not set the switch-off group, parameter set %2
解決方法を見る コード 230-04AA
The switch-off group must be set, parameter set %2
解決方法を見る コード 230-04AB
Parameter %2 not set for parameter set %3
解決方法を見る コード 230-04AC
Inputs for axis-group enabling are ignored
解決方法を見る コード 230-04AD
PL inputs are not allowed as axis-group enabling
解決方法を見る コード 230-04AE
PAE module not configured in IOCP file
解決方法を見る コード 230-04AF
Axis-group enabling machine function configured on PL
解決方法を見る コード 230-04B0
Invalid PWM frequency configured for axis %2
解決方法を見る コード 230-04B3
More safe axes are activated than are enabled in the SIK
解決方法を見る コード 230-04B4
SMC: Missing acknowledgment
解決方法を見る コード 230-04B7
Error in configuration of axis %2
解決方法を見る コード 230-04B9
The signal cannot be recorded
解決方法を見る コード 230-04BA
UVR%2 change of parameters requires restart.
解決方法を見る コード 230-04BC
Warning from EnDat speed encoder on motor in %1 axis ID:
解決方法を見る コード 230-04BD
Advance warning from EnDat position encoder in %1 axis ID:
解決方法を見る コード 230-04BE
Warning from EnDat position encoder in %1 axis ID: %2 SN:
解決方法を見る コード 230-04BF
Fatal error on inverter %2
解決方法を見る コード 230-04C0
Emergency stop by inverter %2
解決方法を見る コード 230-04C1
NC stop by inverter %2
解決方法を見る コード 230-04C2
Brake outputs can't be read by IOCP file
解決方法を見る コード 230-04C3
Brake outputs are ignored
解決方法を見る コード 230-04C4
Two brake outputs refer to the same brake %1
解決方法を見る コード 230-04C5
Control of brake %2 on axis %3 incorrectly configured
解決方法を見る コード 230-04C6
Brake %2: MP_connection must not be configured
解決方法を見る コード 230-04C7
Connection of brake %2 not configured
解決方法を見る コード 230-04C8
Braking connection for brake %2 not configured
解決方法を見る コード 230-04C9
Acceptance testing of safety-relevant parameters %1
解決方法を見る コード 230-04CA
Braking connection for brake %2 incorrectly configured
解決方法を見る コード 230-04CB
Axes switched while in motion
解決方法を見る コード 230-04CC
Deactivate handwheel for axis %3
解決方法を見る コード 230-04CD
Error during conversion of motor %1
解決方法を見る コード 230-04CE
Communication with CC controller unit faulty
解決方法を見る コード 230-04CF
A client with this ID is already logged on
解決方法を見る コード 230-04D0
Configuration server is not ready
解決方法を見る コード 230-04D1
The requested parameter is not available
解決方法を見る コード 230-04D2
Faulty axis configuration (%2)
解決方法を見る コード 230-04D3
Faulty monitoring of the software limit switches
解決方法を見る コード 230-04D4
Emergency stop by CC, %2
解決方法を見る コード 230-04D5
NC stop by CC, %2
解決方法を見る コード 230-04D6
Temp. of the CC too high %2
解決方法を見る コード 230-04D7
Error in acknowledging the sample rate of the UVR
解決方法を見る コード 230-04D8
Error in acknowledging the sample rate of the UVR
解決方法を見る コード 230-04DD
Input for SBC.GLOBAL configured incorrectly
解決方法を見る コード 230-04DE
Input for SBC.GLOBAL must not be configured
解決方法を見る コード 230-04E0
Progmmd. limit switch/protection zone incorrect for axis %2
解決方法を見る コード 230-04E2
Start position of axis (%2) not permissible for block scan
解決方法を見る コード 230-04E3
No complete circle was recorded
解決方法を見る コード 230-04E5
Incorrect UVR/UEC configuration: %2, index invalid: %3
解決方法を見る コード 230-04E6
Incorrect UVR/UEC configuration: config. duplicated: %1 - %2
解決方法を見る コード 230-04E7
Axis movement not permitted while switching the CLP filter
解決方法を見る コード 230-04E8
Underlying velocity is too low
解決方法を見る コード 230-04E9
Not enough RAM to evaluate the measured data
解決方法を見る コード 230-04EA
MEASURE MACHINE STATUS: memory management faulty
解決方法を見る コード 230-04EC
Axis-group enabling disabled while in motion
解決方法を見る コード 230-04ED
Parameters of current controller are not correct %2
解決方法を見る コード 230-04EE
Parameters of current controller are not correct %2
解決方法を見る コード 230-04EF
Parameters of current controller are not correct %2
解決方法を見る コード 230-04F0
Parameters of current controller are not correct %2
解決方法を見る コード 230-04F1
Configuration error in Monitoring
解決方法を見る コード 230-04F2
Run-time error during calculation
解決方法を見る コード 230-04F3
Error with external modules
解決方法を見る コード 230-04F4
Internal (implementation) error
解決方法を見る コード 230-04F5
Missing rights
解決方法を見る コード 230-04F6
Monitoring task results in a warning
解決方法を見る コード 230-04F7
Error while setting up Process Monitoring
解決方法を見る コード 230-04F8
Faulty configuration of Multicast data
解決方法を見る コード 230-04F9
Internal error in the Multicast data interface
解決方法を見る コード 230-04FA
Realtime Container error in the Multicast data interface
解決方法を見る コード 230-04FB
Realtime Container error in monitoring tasks
解決方法を見る コード 230-04FC
Error while calculating the indicators
解決方法を見る コード 230-04FD
Internal error in the NC reactions for monitoring tasks
解決方法を見る コード 230-04FE
Internal error in monitoring tasks
解決方法を見る コード 230-04FF
Error in the table server of monitoring tasks
解決方法を見る コード 230-0500
Error in the formulas used for monitoring tasks
解決方法を見る コード 230-0501
Faulty configuration of the monitoring tasks
解決方法を見る コード 230-0502
Software option for component monitoring is not enabled
解決方法を見る コード 230-0503
Process Monitoring software option is missing
解決方法を見る コード 230-0504
Cancel program after NC stop because of error %2
解決方法を見る コード 230-0505
Frequency too high for eval. slot %s in envelope curve
解決方法を見る コード 230-0506
No monitoring due to an upstream error
解決方法を見る コード 230-0507
Error during graphical visualization of a monitoring task
解決方法を見る コード 230-0508
Process monitoring is deactivated
解決方法を見る コード 230-0509
Process monitoring deactivated until next program start
解決方法を見る コード 230-050A
Returning to the contour (backtrack) not possible for tapping
解決方法を見る コード 230-050B
PLC movement for axis %2 was canceled
解決方法を見る コード 230-050D
Limit switch %1 %2 (axis not referenced)
解決方法を見る コード 230-050E
Axis configuration for axis %2 obsolete
解決方法を見る コード 230-050F
Can't activate the SIK option "FS Control Loop Qty."
解決方法を見る コード 231-4003
EMERGENCY STOP is active (emergency stop test)
解決方法を見る コード 231-4004
EMERGENCY STOP is inactive (emergency stop test)
解決方法を見る コード 231-4005
Stack overflow warning
解決方法を見る コード 231-4007
No interrupt from the gate array
解決方法を見る コード 231-4008
Answer to a host command was too late
解決方法を見る コード 231-4009
False interrupt (AC failure, emergence stop)
解決方法を見る コード 231-400B
Host is prompted to synchronize
解決方法を見る コード 231-4011
Axis %1: measurement interrupted by NC Stop
解決方法を見る コード 231-4110
Encoder contamination in axis %1
解決方法を見る コード 231-4120
Excessive frequency in encoder for axis %1
解決方法を見る コード 231-4130
Contamination of Z1 track in encoder for axis %1
解決方法を見る コード 231-4140
Power module warning: Heat sink temperature in axis
解決方法を見る コード 231-4150
Power module warnung for axis %1
解決方法を見る コード 231-4160
Gate array status reg. = not nicht stored (axis %1)
解決方法を見る コード 231-4170
Error in temperature measurement for axis %1
解決方法を見る コード 231-4200
PLC: Drive is ready for operation in axis %1
解決方法を見る コード 231-4210
PLC: Drive is not ready for operation in axis %1
解決方法を見る コード 231-4220
Standstill recognition (V=0 with IQ_max): (axis %1)
解決方法を見る コード 231-4230
End of standstill recognition in axis %1
解決方法を見る コード 231-4240
Warning for I^2*t monitoring in axis %1
解決方法を見る コード 231-4250
End of warning for I^2*t monitoring in axis %1
解決方法を見る コード 231-4260
Limit through I^2*t monitoring
解決方法を見る コード 231-4270
End of limit through I^2*t monitoring in axis %1
解決方法を見る コード 231-4280
Error during REF scan in axis %1
解決方法を見る コード 231-4290
Drive switch-off (inactive RDY signal) in axis %1
解決方法を見る コード 231-4300
Drive enable in axis %1
解決方法を見る コード 231-4310
Drive disabled, e.g. through emergency stop in axis %1
解決方法を見る コード 231-4400
Excessive following error (axis: %1)
解決方法を見る コード 231-4810
CC (log): actual current value too high %1
解決方法を見る コード 231-5100
Endless loop: Time monitoring (value: %1)
解決方法を見る コード 231-5200
Compensated angle error alignment (value: %1)
解決方法を見る コード 231-5300
Timeout of shaft speed interrupt (value: %1)
解決方法を見る コード 231-5500
Emergency stop failure
解決方法を見る コード 231-6002
Status of machine-on input = 1 after "hcSgMaschi-
解決方法を見る コード 231-6003
Status of machine-on input = 0 after "hcSgMaschi-
解決方法を見る コード 231-6005
STOP1 release due to error in T2 test
解決方法を見る コード 231-6006
Tool changer: "SHS2"-output change to open chuck
解決方法を見る コード 231-6016
STOP2 release: Incorrect power supply
解決方法を見る コード 231-6017
STOP2 release: Out of temperature range
解決方法を見る コード 231-6018
Request for test of pulse deletion
解決方法を見る コード 231-6100
Cut-out channel test: Status change -STO.A.x %1 = 0->1
解決方法を見る コード 231-6140
Negative position monitoring with stop 1
解決方法を見る コード 231-6800
CC (Dbg): test code
解決方法を見る コード 231-6810
CC (Dbg): switch-off position invalid, outside the limit
解決方法を見る コード 231-6820
CC (log): autotest info
解決方法を見る コード 231-6840
CC (log): timer info for monitoring the calling of the
解決方法を見る コード 231-6850
CC (log): LSV2 test command for FS error injection
解決方法を見る コード 231-8000
CC%2 Warning: Temperature of controller card is high
解決方法を見る コード 231-8001
CC%2 Warning: Temperature of controller card is low
解決方法を見る コード 231-8002
CC%2 warning: Fan speed is low
解決方法を見る コード 231-8003
CC%2 early warning: dc-link current too high
解決方法を見る コード 231-8004
CC test software loaded
解決方法を見る コード 231-8005
Oscilloscope signal not supported
解決方法を見る コード 231-8010
LSV2 transmission error
解決方法を見る コード 231-8040
Heat sink temp. in UV 1xx
解決方法を見る コード 231-8041
Excessive Iz in UV 1xx
解決方法を見る コード 231-8042
CC%2 maximum temperature of controller card
解決方法を見る コード 231-8043
CC%2 temperature of controller card below minimum
解決方法を見る コード 231-8044
CC%2 Fan speed too low
解決方法を見る コード 231-8060
Leakage current in UV 1xx
解決方法を見る コード 231-8061
Power module not ready
解決方法を見る コード 231-8062
Limit: Uz too small
解決方法を見る コード 231-8063
CC%2 timeout in S status test
解決方法を見る コード 231-8064
AC powerfail
解決方法を見る コード 231-8065
DC powerfail
解決方法を見る コード 231-8066
CC%2 maximum temperature of controller card
解決方法を見る コード 231-8067
CC%2 temperature of controller card below minimum
解決方法を見る コード 231-8068
CC%2 Fan speed too low
解決方法を見る コード 231-8069
IGBT error in the supply module
解決方法を見る コード 231-806A
Unknown SPI expansion module
解決方法を見る コード 231-806B
Powerfail AC drive cntrller
解決方法を見る コード 231-806C
DC powerfail
解決方法を見る コード 231-8080
Uz UV 1xx exceeds max.
解決方法を見る