Back to all Heidenhain models

Heidenhain TNC Series CNC

Heidenhain TNC Series CNC Error Codes

Complete alarm and error code reference for the Heidenhain TNC Series CNC. Browse all 4497 documented fault codes below, each linking to a detailed troubleshooting guide.

Search this section

Search Heidenhain TNC Series CNC

Search all 4497 Heidenhain TNC Series CNC codes without changing pages.

Search all database

Complete Alarm List (Page 20 of 23)

Incorrect tool for machining.

Incorrect tool for machining.

Incorrect tool for machining.

Incorrect tool for machining.

Incorrect tool for machining.

Incorrect tool for machining.

Incorrect tool for machining.

Incorrect tool for machining.

The main cutting direction does not fit the contour.

Invalid tool orientation for transverse machining (roughing)

Invalid tool orient. for longitudinal machining (roughing)

The cycle cannot completely create the

Programmed cutting depth too small

axis is already braked in the thread

axis is still accelerated in the thread

Determined run-in length is too short

Determined run-out length is too short

"TOOL_P" configured without tool magazine

Tool magazine configured without path for "TOOL_P"

Active tool pocket unknown

Protective zone monitoring not allowed in axis system with B

Starting block of channel <%2> cannot be reached because

Program run blocked due to a serious error

No workpiece blank defined for turning cycle

Calculation of the approach path not possible

Area to be machined was not provided

A negative safety clearance is not allowed

No valid cutting depth was defined; cycle is working

Internal memory of calculating the cuts is full

Too many stepping angles for simultaneous turning cycle

Not a valid machining contour for simultaneous turning

Contour elements not properly marked (simultaneous

Internal error in the simultaneous turning cycle

The contour cannot be completely machined

Simultaneous turning: Tool is too far "behind" input contour

The tilting motion results in a collision with the tool

Simultaneous turning: Tool tip radius must not be null

Tool position not defined

No valid tool contour for simultaneous turning cycle

Collision-free approach/departure could not be calculated

Desired inclination angles can't be reached without collision

Cannot reach desired angle of incidence at beginning of

Clearance angle + cutting edge angle must be less than 180

Cycle changes angle of incidence at starting point

Aux. contour of tool head faulty,

Wear comp. violates holder oversize

Maximum infeed exceeded

Initial tool angle not in permitted inclination range

%2 Residual material will remain

The cycle cannot machine the indicated target contour

Maximum infeed of tool exceeded

The infeed does not match the length of the cutting edge

Finished part no longer located within

System warning: %1

System error: %1

Tool ID %1 not found

Tool not found (%1)

Helix diameter is greater than twice the cutter diameter

Pilot holes were calculated for a different contour

Pilot holes were calculated for a different trochoid width

Pilot holes were calculated with a different oversize

No corners for trochoidal milling present

Pilot holes on the other side of the contour

Tool diameter is too large

Cutter diameter must be less than the trochoid width

Radius for return greater than half the trochoid width

Trochoid width smaller than plunging helix radius

Pilot holes not present

Depth of the pilot hole less than the milling depth

No trochoid width programmed

Programmed oversize too large

Programmed trochoid width too large

Internal software error / 3D graphics switched off

Error when loading a dialog: %1

File '%1' not found

Failed to send internal message

Unable to open configuration server queue

Unable to read configuration data '%1'

Configuration data '%1' could not be written

Internal error!

Internal error: %1

Invalid data in graphic file: %1

No graphic file: %1

Missing object '%1'

Object '%1' is incomplete

Object '%1' already exists

Working plan '%1' is incomplete

Geometry object list is incomplete

Redundant object '%1' present

Environment variable '%1' not defined

Control structure variable '%1' not defined

Maximum nesting depth of control structures has been

Faulty composition of control structure

Unknown control structure '%1'

Invalid value '%1' in object '%2'

Tool data incomplete: '%1'

Error when opening the tool table '%1'

New parameters of input form '%1' inserted

Old parameters of input form '%1' removed

Variable name '%1' already exists

Graphic file '%1' cannot be opened

Graphic file '%1' is too large

Error when writing the tool data '%1'

Object '%1' is faulty

Parameter '%1' not defined

Environment variable '%1' not initialized

Error when reading the tool data '%1'

Configuration data are incomplete

Parameter '%1' not allowed in this formula!

Configuration object '%1' is faulty

Starting position of noncircular contour not in workpiece

Polar starting position is programmed incrementally

Starting position is programmed incrementally

Relative programming of the reciprocation starting position

Absolute programming of the relief vector is not allowed

Relative programming of the infeed starting position is

Programmed axis is not a grinding axis

Programmed value is not interpreted as a coordinate

Incremental programming of the starting position is not

Reciprocation over zero length is not allowed

Pre-position [Ls]

Thread type (0=ext. / 1=int.)

Amount of infeed

Remaining cut division (0 = Yes)

Number of dry runs

Run-out length at end of thread

Rotational speed (rpm)

Peripheral speed (m/min)

Workpiece rotation speed (1/min)

Taper angle (>0 = ascending)

Stndrd thread (0=none, 1=ISO,..)

Nominal diameter

Thread 0=righthand,1=lefthand

Length of cut in depth

Traversing speed

Speed on run-out

Target position X

Target position Z

Reciprocation feed rate [F]

Infeed rate [D]

Number of spark-out strokes [H]

Tool number (T0 - T9)

Error consequence

Dresser location

Type of machining

Linear measurement

Define the wheel shape

Define the tool

Delete the dresser

Spindle dresser

Diamond dresser

Dresser alignment

Teach in dresser position

Transmission ratio

Reload the data

Search criteria

Confirm the data

Previous identical

Tool information

Internal grinding

External grinding

General wheel data

3801-4000 of 4497