Volver a todos los modelos de Siemens Search all database
Siemens SINUMERIK 840D CNC
Códigos de error de Siemens SINUMERIK 840D CNC
Referencia completa de códigos de alarma y error para Siemens SINUMERIK 840D CNC. Explore a continuación los 4014 códigos de falla documentados, cada uno con un enlace a una guía detallada de solución de problemas.
Search this section
Search Siemens SINUMERIK 840D CNC
Search all 4014 Siemens SINUMERIK 840D CNC codes without changing pages.
Lista completa de alarmas (Page 9 of 21)
Código 61277
[Channel %1: ] Block %2: Tool diameter larger than restriction
Ver solución Código 61278
[Channel %1: ] Block %2: If tool angle is larger than 90°, both tool diameters must be equal
Ver solución Código 61279
[Channel %1: ] Block %2: If tool a ngle equals 90°, both tool diameters must be equal
Ver solución Código 61280
[Channel %1: ] Block %2: Mirroring in WO %4 missing
Ver solución Código 61281
[Channel %1: ] Block %2: starting point of machining outside retraction planes
Ver solución Código 61282
[Channel %1: ] Block %2: end point of machining outside retraction planes
Ver solución Código 61283
[Channel %1: ] Block %2: direct a pproach not possible, as tool change required
Ver solución Código 61284
[Channel %1: ] Block %2: starting point cannot be approached without collision. Pre-position tool manually
Ver solución Código 61285
[Channel %1: ] Block %2: parking position is below return plane XRA.
Ver solución Código 61286
[Channel %1: ] Block %2: machining not possible, check tool angle.
Ver solución Código 61287
[Channel %1: ] Block %2: no master spindle active.
Ver solución Código 61288
[Channel %1: ] Block %2: Main spindle not set up
Ver solución Código 61289
[Channel %1: ] Block %2: Counterspindle not set up
Ver solución Código 61290
[Channel %1: ] Block %2:Tool spindle not set up
Ver solución Código 61291
[Channel %1: ] Block %2: Linear axis of counterspindle not set up
Ver solución Código 61292
[Channel %1: ] Block %2: B axis not set up
Ver solución Código 61293
[Channel %1: ] Block %2: Tool %4 has no spindle rotation direction
Ver solución Código 61300
[Channel %1: ] Block %2: Probe defective
Ver solución Código 61301
[Channel %1: ] Block %2: Probe not switching
Ver solución Código 61302
[Channel %1: ] Block %2: Probe - collision
Ver solución Código 61303
[Channel %1: ] Block %2: Safety margin exceeded
Ver solución Código 61304
[Channel %1: ] Block %2: Allowance
Ver solución Código 61305
[Channel %1: ] Block %2: Dimension too small
Ver solución Código 61306
[Channel %1: ] Block %2: Permissible measuring difference exceeded
Ver solución Código 61307
[Channel %1: ] Block %2: Incorrect measuring variant
Ver solución Código 61308
[Channel %1: ] Block %2: Check measuring path
Ver solución Código 61309
[Channel %1: ] Block %2: Check probe type
Ver solución Código 61310
[Channel %1: ] Block %2: Scale factor is active
Ver solución Código 61311
[Channel %1: ] Block %2: No D number active
Ver solución Código 61312
[Channel %1: ] Block %2: Check measuring cycle number
Ver solución Código 61313
[Channel %1: ] Block %2: Check probe number
Ver solución Código 61314
[Channel %1: ] Block %2: Check selected tool type
Ver solución Código 61315
[Channel %1: ] Block %2: Check position of cutting edge
Ver solución Código 61316
[Channel %1: ] Block %2: Center and radius cannot be determined
Ver solución Código 61317
[Channel %1: ] Block %2: Check number of circle calculation points
Ver solución Código 61318
[Channel %1: ] Block %2: Check weighting factor
Ver solución Código 61319
[Channel %1: ] Block %2: Check call parameter CYCLE114
Ver solución Código 61320
[Channel %1: ] Block %2: Check tool number
Ver solución Código 61321
[Channel %1: ] Block %2: Check WO memory number
Ver solución Código 61322
[Channel %1: ] Block %2: Check 4th digit of _KNUM
Ver solución Código 61323
[Channel %1: ] Block %2: Check 5th digit of _KNUM
Ver solución Código 61324
[Channel %1: ] Block %2: Check 6th digit of _KNUM
Ver solución Código 61325
[Channel %1: ] Block %2: Check measuring axis/offset axis
Ver solución Código 61326
[Channel %1: ] Block %2: Check measuring direction
Ver solución Código 61327
[Channel %1: ] Block %2 : Program reset required
Ver solución Código 61328
[Channel %1: ] Block %2: Check D number
Ver solución Código 61329
[Channel %1: ] Block %2: Check rotary axis
Ver solución Código 61330
[Channel %1: ] Block %2: Coordinate rotation active
Ver solución Código 61331
[Channel %1: ] Block %2: Angle too large, change measuring axis
Ver solución Código 61332
[Channel %1: ] Block %2: Modify tool tip position
Ver solución Código 61333
[Channel %1: ] Block %2: Check calibration block number
Ver solución Código 61334
[Channel %1: ] Block %2: Check safety area
Ver solución Código 61336
[Channel %1: ] Block %2: Geometry axes do not exist
Ver solución Código 61337
[Channel %1: ] Block %2: Check measuring input
Ver solución Código 61338
[Channel %1: ] Block %2: Positioning speed equal to zero
Ver solución Código 61339
[Channel %1: ] Block %2:Correction factor for rapid traverse speed = 0
Ver solución Código 61340
[Channel %1: ] Block %2 : Incorrect alarm number
Ver solución Código 61341
[Channel %1: ] Block %2: Probe not calibrated in active plane.
Ver solución Código 61342
[Channel %1: ] Block %2: Upgrade NCK software version
Ver solución Código 61343
[Channel %1: ] Block %2: No tool available for specified tool name
Ver solución Código 61344
[Channel %1: ] Block %2: Several tools are active
Ver solución Código 61345
[Channel %1: ] Block %2: D number of tool offset, too many digits
Ver solución Código 61346
[Channel %1: ] Block %2: Distance between starting point and measuring point <=0
Ver solución Código 61347
[Channel %1: ] Block %2: Angle 1st edge - 2nd edge equals 0
Ver solución Código 61348
[Channel %1: ] Block %2: Angle rel. to reference edge equals 0
Ver solución Código 61349
[Channel %1: ] Block %2: Distance upper probe edge - measuring position = 0 for tool radius measurement
Ver solución Código 61350
[Channel %1: ] Block %2: Feed, speed not programmed for tool measurement with rotating spindle
Ver solución Código 61351
[Channel %1: ] Block %2: Tool length or radius is 0
Ver solución Código 61352
[Channel %1: ] Block %2: Path for logfile not permitted
Ver solución Código 61353
[Channel %1: ] Block %2: Path for logfile not found
Ver solución Código 61354
[Channel %1: ] Block %2: File for logfile not found
Ver solución Código 61355
[Channel %1: ] Block %2: Incorrect file type for logfile
Ver solución Código 61356
[Channel %1: ] Block %2: File for logfile is being used
Ver solución Código 61357
[Channel %1: ] Block %2: No resources free
Ver solución Código 61358
[Channel %1: ] Block %2: Error during recording
Ver solución Código 61359
[Channel %1: ] Block %2 : - continue with RESET
Ver solución Código 61360
[Channel %1: ] Bloc k %2: Log job undefined - continue with RESET
Ver solución Código 61361
[Channel %1: ] Block %2: Variable cannot be recorded
Ver solución Código 61362
[Channel %1: ] Block %2: Cycle118: No. of values too large
Ver solución Código 61363
[Channel %1: ] Block %2: Max. no. of value lines for recording exceeded
Ver solución Código 61364
[Channel %1: ] Block %2: Check distance from measuring point 1 to measuring point 2
Ver solución Código 61365
[Channel %1: ] Block %2: Check circular feed
Ver solución Código 61366
[Channel %1: ] Block %2: Direction of rotation for tool measurement with rotating spindle not specified.
Ver solución Código 61367
[Channel %1: ] Block %2: Parameters _SETV[0...3] or _SETV[4...7] are identical
Ver solución Código 61368
[Channel %1: ] Block %2: Straights through parameter _SETV[0...3] or _SETV[4...7]do not intersect
Ver solución Código 61369
[Channel %1: ] Block %2: Position of corner not clearly definable, check parameter _SETV[0...7]
Ver solución Código 61370
[Channel %1: ] Block %2: _PROTVAL[0] -_PROTVAL[5] do not have any entries
Ver solución Código 61371
[Channel %1: ] Block %2: Product of column width and number of columns exceeds 200 characters per line
Ver solución Código 61372
[Channel %1: ] Block %2: selected meas.variant requires SPOS-capable spindle
Ver solución Código 61373
[Channel %1: ] Block %2: Mono-directional probe requires SPOS-capable spindle
Ver solución Código 61401
[Channel %1: ] Block %2: Probe does not switch, traversing path limited by software limit position.
Ver solución Código 61402
[Channel %1: ] Block %2: Probe col lision, traversing path limited by software limit position
Ver solución Código 61403
[Channel %1: ] Block %2: Work offset correction not executed
Ver solución Código 61404
[Channel %1: ] Block %2: Tool correction not executed
Ver solución Código 61405
[Channel %1: ] Block %2: Tool environment does not exist
Ver solución Código 61406
[Channel %1: ] Block %2: Check DL number
Ver solución Código 61407
[Channel %1: ] Block %2: Check 7th digit and higher of _KNUM
Ver solución Código 61408
[Channel %1: ] Block %2: total offsets not present
Ver solución Código 61409
[Channel %1: ] Block %2: set up offsets not present
Ver solución Código 61410
[Channel %1: ] Block %2 access to nonexistent tool element or property
Ver solución Código 61411
[Channel %1: ] Block %2: Check the distribution of measuring points on the plane.
Ver solución Código 61412
[Channel %1: ] Block %2: channel basic frame not present
Ver solución Código 61413
[Channel %1: ] Block %2: check setpoint of ball diameter, _SETVAL<=0
Ver solución Código 61414
[Channel %1: ] Block %2 : distortion of triangle over limit
Ver solución Código 61415
[Channel %1: ] Block %2: Check probe / machining plane
Ver solución Código 61416
[Channel %1: ] Block %2: adapt array size %4!
Ver solución Código 61417
[Channel %1: ] Block %2: Probe will collide with the carrier of the reference groove.
Ver solución Código 61418
[Channel %1: ] Block %2: Protocol file too small, check MD11420: LEN_PROTOCOL_FILE.
Ver solución Código 61419
[Channel %1: ] Block %2: Check probe calibration with reference to center of ball/circumference of ball.
Ver solución Código 61420
[Channel %1: ] Block %2: Check calibration of multi/mono probes.
Ver solución Código 61421
[Channel %1: ] Block %2: Software release of measuring cycles or NCK inadequate or set up inco rrectly --> error code %4
Ver solución Código 61422
[Channel %1: ] Block %2: Parameter _MVAR incorrect --> Error code: %4
Ver solución Código 61423
[Channel %1: ] Block %2: Parameter _TNUM not agreed or not created
Ver solución Código 61424
[Channel %1: ] Block %2: Parameter _SETVAL for diameter of calibration ball incorrect
Ver solución Código 61425
[Channel %1: ] Block %2: Parameter fo r measuring axis rotary axis 1 or 2 incorrect -> Error code: %4
Ver solución Código 61426
[Channel %1: ] Block %2: Sum of the active offsets does not equal zero - > Error code: %4
Ver solución Código 61427
[Channel %1: ] Block %2: Tool data of the active workpiece probe incorrect or inactive --> Error code: %4
Ver solución Código 61428
[Channel %1: ] Block %2: Error while creating log file -> Error code: %4
Ver solución Código 61429
[Channel %1: ] Block %2: Measuring axis (rotary axis 1 or 2) not in basic or intended position -> Error code: %4
Ver solución Código 61430
[Channel %1: ] Block %2: Kinematic vectors not computed -> Error code: %4
Ver solución Código 61440
[Channel %1: ] Block %2: Position of cutting edge cannot be determined
Ver solución Código 61441
[Channel %1: ] Block %2: Position of cutting edge is not in the machining plane.
Ver solución Código 61442
[Channel %1: ] Block %2: Tool carrier not parallel to the geometry axes
Ver solución Código 61443
[Channel %1: ] Block %2: Advance angle _INCA=0 or greater/less than +/- 90° or +/-120°
Ver solución Código 61444
[Channel %1: ] Block %2: Current measuring speed is not identical to the calibration speed
Ver solución Código 61501
[Channel %1: ] Block %2: Simulation is active
Ver solución Código 61502
[Channel %1: ] Block %2: No tool offset active
Ver solución Código 61503
[Channel %1: ] Block %2: tool nos e radius compensation left or right
Ver solución Código 61504
[Channel %1: ] Block %2: _KNG incorrect for setup
Ver solución Código 61505
[Channel %1: ] Block %2: retraction path < 1mm
Ver solución Código 61506
[Channel %1: ] Block %2: infeed path < 1mm
Ver solución Código 61507
[Channel %1: ] Block %2: safety clearance < 1mm
Ver solución Código 61508
[Channel %1: ] Block %2: Incorrect default setting for shoulder position
Ver solución Código 61509
[Channel %1: ] Block %2: Incorrect default setting for dresser position
Ver solución Código 61510
[Channel %1: ] Block %2: Test run feed is active
Ver solución Código 61511
[Channel %1: ] Block %2: Incorrect s houlder position or tool edge D1/D2
Ver solución Código 61512
[Channel %1: ] Block %2: Incorrect longitudinal position
Ver solución Código 61513
[Channel %1: ] Block %2: Dresser left and inclined grinding wheel
Ver solución Código 61514
[Channel %1: ] Block %2: Grinding wheel type missing
Ver solución Código 61515
[Channel %1: ] Block %2: Retraction path <= dressing amount
Ver solución Código 61517
[Channel %1: ] Block %2: Angle of inclined grinding wheel missing
Ver solución Código 61518
[Channel %1: ] Block %2: Shoulder height of grinding wheel must be > grinding wheel radius
Ver solución Código 61519
[Channel %1: ] Block %2: Incorrect type of machining
Ver solución Código 61520
[Channel %1: ] Block %2: Additional offsets not set
Ver solución Código 61521
[Channel %1: ] Block %2: Current grinding wheel too wide
Ver solución Código 61522
[Channel %1: ] Block %2: Overla p >= current grinding wheel width
Ver solución Código 61523
[Channel %1: ] Block %2: Zero signal of calipers missing
Ver solución Código 61524
[Channel %1: ] Block %2: Incorrect oblique angle
Ver solución Código 61525
[Channel %1: ] Block %2: Incorrect grinding wheel type
Ver solución Código 61526
[Channel %1: ] Block %2: Workpiece radius = 0
Ver solución Código 61527
[Channel %1: ] Block %2: Grindi ng wheel radius >= workpiece radius
Ver solución Código 61529
[Channel %1: ] Block %2: Dimensional notation INCH programmed
Ver solución Código 61530
[Channel %1: ] Block %2: Default longitudinal position incorrect
Ver solución Código 61531
[Channel %1: ] Block %2: Longitudinal position not registered in Z
Ver solución Código 61532
[Channel %1: ] Block %2: Value for _LAGE is incorrect
Ver solución Código 61533
[Channel %1: ] Block %2: No length L1 entered under D...
Ver solución Código 61540
[Channel %1: ] Block %2: Incorrect D number / dresser D field active
Ver solución Código 61541
[Channel %1: ] Block %2: Incorrect grinding wheel type entered
Ver solución Código 61542
[Channel %1: ] Block %2: Incorrect grinding wheel reference point selected when selecting the dresser coordinate system
Ver solución Código 61543
[Channel %1: ] Block %2: Incorrect dresser selected when selecting the dresser coordinate system
Ver solución Código 61544
[Channel %1: ] Block %2: Gri nding wheel diameter worn down
Ver solución Código 61545
[Channel %1: ] Block %2: Widt h of grinding wheel worn down
Ver solución Código 61546
[Channel %1: ] Block %2: Dresser %4, wear limit length 1 reached
Ver solución Código 61547
[Channel %1: ] Block %2: Dresser %4, wear limit length 2 reached
Ver solución Código 61548
[Channel %1: ] Block %2: Dresser %4, wear limit length 3 reached
Ver solución Código 61549
[Channel %1: ] Block %2: Incorrect dresser type selected
Ver solución Código 61555
[Channel %1: ] Block %2: Diameter of grinding wheel ==0, GWPS cannot be calculated
Ver solución Código 61556
[Channel %1: ] Block %2: Impossible chamfer and radius of left edge of wheel
Ver solución Código 61557
[Channel %1: ] Block %2: Impossible chamfer and radius of right edge of wheel
Ver solución Código 61558
[Channel %1: ] Block %2: Chamfer / radius + shoulder height are less than the retraction height of the left edge of the grinding wheel
Ver solución Código 61559
[Channel %1: ] Block %2: Chamfer / radius + shoulder height are less than the retraction height of the right edge of the grinding wheel
Ver solución Código 61560
[Channel %1: ] Block %2: Infeed in Z direction too big per stroke, or wheel too narrow
Ver solución Código 61561
[Channel %1: ] Block %2: Feed left wheel edge <=0
Ver solución Código 61562
[Channel %1: ] Block %2: Feed right wheel edge <=0
Ver solución Código 61563
[Channel %1: ] Block %2: Feed on the diameter <=0
Ver solución Código 61564
[Channel %1: ] Block %2: Feed insertion <=0
Ver solución Código 61565
[Channel %1: ] Block %2: Feed dressing <=0
Ver solución Código 61601
[Channel %1: ] Block %2: Finished part diameter too small
Ver solución Código 61602
[Channel %1: ] Block %2: Tool width incorrectly defined
Ver solución Código 61603
[Channel %1: ] Block %2: Recess type incorrectly defined
Ver solución Código 61604
[Channel %1: ] Block %2: Active tool violates programmed contour
Ver solución Código 61605
[Channel %1: ] Block %2: Contour incorrectly programmed
Ver solución Código 61606
[Channel %1: ] Block %2: Error during contour preparation
Ver solución Código 61607
[Channel %1: ] Block %2: Starting point incorrectly programmed
Ver solución Código 61608
[Channel %1: ] Block %2: Incorrect tool point direction programmed
Ver solución Código 61609
[Channel %1: ] Block %2: Shape incorrectly defined
Ver solución Código 61610
[Channel %1: ] Block %2: No infeed depth programmed
Ver solución Código 61611
[Channel %1: ] Block %2: No point of intersection found
Ver solución Código 61612
[Channel %1: ] Block %2: Thread finishing not possible
Ver solución Código 61613
[Channel %1: ] Block %2: Undercut position incorrectly defined
Ver solución Código 61700
[Channel %1: ] Block %2: Name of program to be generated is missing
Ver solución Código 61701
[Channel %1: ] Block %2: Contour %4 does not exist
Ver solución Código 61702
[Channel %1: ] Block %2: Label %4 not existing in machined part contour
Ver solución Código 61703
[Channel %1: ] Block %2: Label %4 not existing in the blank contour
Ver solución Código 61704
[Channel %1: ] Block %2: Machined part contour missing
Ver solución Código 61705
[Channel %1: ] Block %2: Blank contour missing
Ver solución Código 61706
[Channel %1: ] Block %2: Error in machined part contour %4
Ver solución Código 61707
[Channel %1: ] Block %2: Error in the blank contour %4
Ver solución Código 61708
[Channel %1: ] Block %2: Too many contours specified
Ver solución Código 61709
[Channel %1: ] Block %2: Cutting edge radius too small
Ver solución