Siemens SINUMERIK 840D CNC 錯誤代碼

[Channel %1: ] Block %2: Tool diameter larger than restriction

[Channel %1: ] Block %2: If tool angle is larger than 90°, both tool diameters must be equal

[Channel %1: ] Block %2: If tool a ngle equals 90°, both tool diameters must be equal

[Channel %1: ] Block %2: Mirroring in WO %4 missing

[Channel %1: ] Block %2: starting point of machining outside retraction planes

[Channel %1: ] Block %2: end point of machining outside retraction planes

[Channel %1: ] Block %2: direct a pproach not possible, as tool change required

[Channel %1: ] Block %2: starting point cannot be approached without collision. Pre-position tool manually

[Channel %1: ] Block %2: parking position is below return plane XRA.

[Channel %1: ] Block %2: machining not possible, check tool angle.

[Channel %1: ] Block %2: no master spindle active.

[Channel %1: ] Block %2: Main spindle not set up

[Channel %1: ] Block %2: Counterspindle not set up

[Channel %1: ] Block %2:Tool spindle not set up

[Channel %1: ] Block %2: Linear axis of counterspindle not set up

[Channel %1: ] Block %2: B axis not set up

[Channel %1: ] Block %2: Tool %4 has no spindle rotation direction

[Channel %1: ] Block %2: Probe defective

[Channel %1: ] Block %2: Probe not switching

[Channel %1: ] Block %2: Probe - collision

[Channel %1: ] Block %2: Safety margin exceeded

[Channel %1: ] Block %2: Allowance

[Channel %1: ] Block %2: Dimension too small

[Channel %1: ] Block %2: Permissible measuring difference exceeded

[Channel %1: ] Block %2: Incorrect measuring variant

[Channel %1: ] Block %2: Check measuring path

[Channel %1: ] Block %2: Check probe type

[Channel %1: ] Block %2: Scale factor is active

[Channel %1: ] Block %2: No D number active

[Channel %1: ] Block %2: Check measuring cycle number

[Channel %1: ] Block %2: Check probe number

[Channel %1: ] Block %2: Check selected tool type

[Channel %1: ] Block %2: Check position of cutting edge

[Channel %1: ] Block %2: Center and radius cannot be determined

[Channel %1: ] Block %2: Check number of circle calculation points

[Channel %1: ] Block %2: Check weighting factor

[Channel %1: ] Block %2: Check call parameter CYCLE114

[Channel %1: ] Block %2: Check tool number

[Channel %1: ] Block %2: Check WO memory number

[Channel %1: ] Block %2: Check 4th digit of _KNUM

[Channel %1: ] Block %2: Check 5th digit of _KNUM

[Channel %1: ] Block %2: Check 6th digit of _KNUM

[Channel %1: ] Block %2: Check measuring axis/offset axis

[Channel %1: ] Block %2: Check measuring direction

[Channel %1: ] Block %2 : Program reset required

[Channel %1: ] Block %2: Check D number

[Channel %1: ] Block %2: Check rotary axis

[Channel %1: ] Block %2: Coordinate rotation active

[Channel %1: ] Block %2: Angle too large, change measuring axis

[Channel %1: ] Block %2: Modify tool tip position

[Channel %1: ] Block %2: Check calibration block number

[Channel %1: ] Block %2: Check safety area

[Channel %1: ] Block %2: Geometry axes do not exist

[Channel %1: ] Block %2: Check measuring input

[Channel %1: ] Block %2: Positioning speed equal to zero

[Channel %1: ] Block %2:Correction factor for rapid traverse speed = 0

[Channel %1: ] Block %2 : Incorrect alarm number

[Channel %1: ] Block %2: Probe not calibrated in active plane.

[Channel %1: ] Block %2: Upgrade NCK software version

[Channel %1: ] Block %2: No tool available for specified tool name

[Channel %1: ] Block %2: Several tools are active

[Channel %1: ] Block %2: D number of tool offset, too many digits

[Channel %1: ] Block %2: Distance between starting point and measuring point <=0

[Channel %1: ] Block %2: Angle 1st edge - 2nd edge equals 0

[Channel %1: ] Block %2: Angle rel. to reference edge equals 0

[Channel %1: ] Block %2: Distance upper probe edge - measuring position = 0 for tool radius measurement

[Channel %1: ] Block %2: Feed, speed not programmed for tool measurement with rotating spindle

[Channel %1: ] Block %2: Tool length or radius is 0

[Channel %1: ] Block %2: Path for logfile not permitted

[Channel %1: ] Block %2: Path for logfile not found

[Channel %1: ] Block %2: File for logfile not found

[Channel %1: ] Block %2: Incorrect file type for logfile

[Channel %1: ] Block %2: File for logfile is being used

[Channel %1: ] Block %2: No resources free

[Channel %1: ] Block %2: Error during recording

[Channel %1: ] Block %2 : - continue with RESET

[Channel %1: ] Bloc k %2: Log job undefined - continue with RESET

[Channel %1: ] Block %2: Variable cannot be recorded

[Channel %1: ] Block %2: Cycle118: No. of values too large

[Channel %1: ] Block %2: Max. no. of value lines for recording exceeded

[Channel %1: ] Block %2: Check distance from measuring point 1 to measuring point 2

[Channel %1: ] Block %2: Check circular feed

[Channel %1: ] Block %2: Direction of rotation for tool measurement with rotating spindle not specified.

[Channel %1: ] Block %2: Parameters _SETV[0...3] or _SETV[4...7] are identical

[Channel %1: ] Block %2: Straights through parameter _SETV[0...3] or _SETV[4...7]do not intersect

[Channel %1: ] Block %2: Position of corner not clearly definable, check parameter _SETV[0...7]

[Channel %1: ] Block %2: _PROTVAL[0] -_PROTVAL[5] do not have any entries

[Channel %1: ] Block %2: Product of column width and number of columns exceeds 200 characters per line

[Channel %1: ] Block %2: selected meas.variant requires SPOS-capable spindle

[Channel %1: ] Block %2: Mono-directional probe requires SPOS-capable spindle

[Channel %1: ] Block %2: Probe does not switch, traversing path limited by software limit position.

[Channel %1: ] Block %2: Probe col lision, traversing path limited by software limit position

[Channel %1: ] Block %2: Work offset correction not executed

[Channel %1: ] Block %2: Tool correction not executed

[Channel %1: ] Block %2: Tool environment does not exist

[Channel %1: ] Block %2: Check DL number

[Channel %1: ] Block %2: Check 7th digit and higher of _KNUM

[Channel %1: ] Block %2: total offsets not present

[Channel %1: ] Block %2: set up offsets not present

[Channel %1: ] Block %2 access to nonexistent tool element or property

[Channel %1: ] Block %2: Check the distribution of measuring points on the plane.

[Channel %1: ] Block %2: channel basic frame not present

[Channel %1: ] Block %2: check setpoint of ball diameter, _SETVAL<=0

[Channel %1: ] Block %2 : distortion of triangle over limit

[Channel %1: ] Block %2: Check probe / machining plane

[Channel %1: ] Block %2: adapt array size %4!

[Channel %1: ] Block %2: Probe will collide with the carrier of the reference groove.

[Channel %1: ] Block %2: Protocol file too small, check MD11420: LEN_PROTOCOL_FILE.

[Channel %1: ] Block %2: Check probe calibration with reference to center of ball/circumference of ball.

[Channel %1: ] Block %2: Check calibration of multi/mono probes.

[Channel %1: ] Block %2: Software release of measuring cycles or NCK inadequate or set up inco rrectly --> error code %4

[Channel %1: ] Block %2: Parameter _MVAR incorrect --> Error code: %4

[Channel %1: ] Block %2: Parameter _TNUM not agreed or not created

[Channel %1: ] Block %2: Parameter _SETVAL for diameter of calibration ball incorrect

[Channel %1: ] Block %2: Parameter fo r measuring axis rotary axis 1 or 2 incorrect -> Error code: %4

[Channel %1: ] Block %2: Sum of the active offsets does not equal zero - > Error code: %4

[Channel %1: ] Block %2: Tool data of the active workpiece probe incorrect or inactive --> Error code: %4

[Channel %1: ] Block %2: Error while creating log file -> Error code: %4

[Channel %1: ] Block %2: Measuring axis (rotary axis 1 or 2) not in basic or intended position -> Error code: %4

[Channel %1: ] Block %2: Kinematic vectors not computed -> Error code: %4

[Channel %1: ] Block %2: Position of cutting edge cannot be determined

[Channel %1: ] Block %2: Position of cutting edge is not in the machining plane.

[Channel %1: ] Block %2: Tool carrier not parallel to the geometry axes

[Channel %1: ] Block %2: Advance angle _INCA=0 or greater/less than +/- 90° or +/-120°

[Channel %1: ] Block %2: Current measuring speed is not identical to the calibration speed

[Channel %1: ] Block %2: Simulation is active

[Channel %1: ] Block %2: No tool offset active

[Channel %1: ] Block %2: tool nos e radius compensation left or right

[Channel %1: ] Block %2: _KNG incorrect for setup

[Channel %1: ] Block %2: retraction path < 1mm

[Channel %1: ] Block %2: infeed path < 1mm

[Channel %1: ] Block %2: safety clearance < 1mm

[Channel %1: ] Block %2: Incorrect default setting for shoulder position

[Channel %1: ] Block %2: Incorrect default setting for dresser position

[Channel %1: ] Block %2: Test run feed is active

[Channel %1: ] Block %2: Incorrect s houlder position or tool edge D1/D2

[Channel %1: ] Block %2: Incorrect longitudinal position

[Channel %1: ] Block %2: Dresser left and inclined grinding wheel

[Channel %1: ] Block %2: Grinding wheel type missing

[Channel %1: ] Block %2: Retraction path <= dressing amount

[Channel %1: ] Block %2: Angle of inclined grinding wheel missing

[Channel %1: ] Block %2: Shoulder height of grinding wheel must be > grinding wheel radius

[Channel %1: ] Block %2: Incorrect type of machining

[Channel %1: ] Block %2: Additional offsets not set

[Channel %1: ] Block %2: Current grinding wheel too wide

[Channel %1: ] Block %2: Overla p >= current grinding wheel width

[Channel %1: ] Block %2: Zero signal of calipers missing

[Channel %1: ] Block %2: Incorrect oblique angle

[Channel %1: ] Block %2: Incorrect grinding wheel type

[Channel %1: ] Block %2: Workpiece radius = 0

[Channel %1: ] Block %2: Grindi ng wheel radius >= workpiece radius

[Channel %1: ] Block %2: Dimensional notation INCH programmed

[Channel %1: ] Block %2: Default longitudinal position incorrect

[Channel %1: ] Block %2: Longitudinal position not registered in Z

[Channel %1: ] Block %2: Value for _LAGE is incorrect

[Channel %1: ] Block %2: No length L1 entered under D...

[Channel %1: ] Block %2: Incorrect D number / dresser D field active

[Channel %1: ] Block %2: Incorrect grinding wheel type entered

[Channel %1: ] Block %2: Incorrect grinding wheel reference point selected when selecting the dresser coordinate system

[Channel %1: ] Block %2: Incorrect dresser selected when selecting the dresser coordinate system

[Channel %1: ] Block %2: Gri nding wheel diameter worn down

[Channel %1: ] Block %2: Widt h of grinding wheel worn down

[Channel %1: ] Block %2: Dresser %4, wear limit length 1 reached

[Channel %1: ] Block %2: Dresser %4, wear limit length 2 reached

[Channel %1: ] Block %2: Dresser %4, wear limit length 3 reached

[Channel %1: ] Block %2: Incorrect dresser type selected

[Channel %1: ] Block %2: Diameter of grinding wheel ==0, GWPS cannot be calculated

[Channel %1: ] Block %2: Impossible chamfer and radius of left edge of wheel

[Channel %1: ] Block %2: Impossible chamfer and radius of right edge of wheel

[Channel %1: ] Block %2: Chamfer / radius + shoulder height are less than the retraction height of the left edge of the grinding wheel

[Channel %1: ] Block %2: Chamfer / radius + shoulder height are less than the retraction height of the right edge of the grinding wheel

[Channel %1: ] Block %2: Infeed in Z direction too big per stroke, or wheel too narrow

[Channel %1: ] Block %2: Feed left wheel edge <=0

[Channel %1: ] Block %2: Feed right wheel edge <=0

[Channel %1: ] Block %2: Feed on the diameter <=0

[Channel %1: ] Block %2: Feed insertion <=0

[Channel %1: ] Block %2: Feed dressing <=0

[Channel %1: ] Block %2: Finished part diameter too small

[Channel %1: ] Block %2: Tool width incorrectly defined

[Channel %1: ] Block %2: Recess type incorrectly defined

[Channel %1: ] Block %2: Active tool violates programmed contour

[Channel %1: ] Block %2: Contour incorrectly programmed

[Channel %1: ] Block %2: Error during contour preparation

[Channel %1: ] Block %2: Starting point incorrectly programmed

[Channel %1: ] Block %2: Incorrect tool point direction programmed

[Channel %1: ] Block %2: Shape incorrectly defined

[Channel %1: ] Block %2: No infeed depth programmed

[Channel %1: ] Block %2: No point of intersection found

[Channel %1: ] Block %2: Thread finishing not possible

[Channel %1: ] Block %2: Undercut position incorrectly defined

[Channel %1: ] Block %2: Name of program to be generated is missing

[Channel %1: ] Block %2: Contour %4 does not exist

[Channel %1: ] Block %2: Label %4 not existing in machined part contour

[Channel %1: ] Block %2: Label %4 not existing in the blank contour

[Channel %1: ] Block %2: Machined part contour missing

[Channel %1: ] Block %2: Blank contour missing

[Channel %1: ] Block %2: Error in machined part contour %4

[Channel %1: ] Block %2: Error in the blank contour %4

[Channel %1: ] Block %2: Too many contours specified

[Channel %1: ] Block %2: Cutting edge radius too small