Back to all Siemens models Search all database
Siemens SINUMERIK 840D CNC
Siemens SINUMERIK 840D CNC Error Codes
Complete alarm and error code reference for the Siemens SINUMERIK 840D CNC. Browse all 4014 documented fault codes below, each linking to a detailed troubleshooting guide.
Search this section
Search Siemens SINUMERIK 840D CNC
Search all 4014 Siemens SINUMERIK 840D CNC codes without changing pages.
Complete Alarm List (Page 9 of 21)
Code 61277
[Channel %1: ] Block %2: Tool diameter larger than restriction
View solution Code 61278
[Channel %1: ] Block %2: If tool angle is larger than 90°, both tool diameters must be equal
View solution Code 61279
[Channel %1: ] Block %2: If tool a ngle equals 90°, both tool diameters must be equal
View solution Code 61280
[Channel %1: ] Block %2: Mirroring in WO %4 missing
View solution Code 61281
[Channel %1: ] Block %2: starting point of machining outside retraction planes
View solution Code 61282
[Channel %1: ] Block %2: end point of machining outside retraction planes
View solution Code 61283
[Channel %1: ] Block %2: direct a pproach not possible, as tool change required
View solution Code 61284
[Channel %1: ] Block %2: starting point cannot be approached without collision. Pre-position tool manually
View solution Code 61285
[Channel %1: ] Block %2: parking position is below return plane XRA.
View solution Code 61286
[Channel %1: ] Block %2: machining not possible, check tool angle.
View solution Code 61287
[Channel %1: ] Block %2: no master spindle active.
View solution Code 61288
[Channel %1: ] Block %2: Main spindle not set up
View solution Code 61289
[Channel %1: ] Block %2: Counterspindle not set up
View solution Code 61290
[Channel %1: ] Block %2:Tool spindle not set up
View solution Code 61291
[Channel %1: ] Block %2: Linear axis of counterspindle not set up
View solution Code 61292
[Channel %1: ] Block %2: B axis not set up
View solution Code 61293
[Channel %1: ] Block %2: Tool %4 has no spindle rotation direction
View solution Code 61300
[Channel %1: ] Block %2: Probe defective
View solution Code 61301
[Channel %1: ] Block %2: Probe not switching
View solution Code 61302
[Channel %1: ] Block %2: Probe - collision
View solution Code 61303
[Channel %1: ] Block %2: Safety margin exceeded
View solution Code 61304
[Channel %1: ] Block %2: Allowance
View solution Code 61305
[Channel %1: ] Block %2: Dimension too small
View solution Code 61306
[Channel %1: ] Block %2: Permissible measuring difference exceeded
View solution Code 61307
[Channel %1: ] Block %2: Incorrect measuring variant
View solution Code 61308
[Channel %1: ] Block %2: Check measuring path
View solution Code 61309
[Channel %1: ] Block %2: Check probe type
View solution Code 61310
[Channel %1: ] Block %2: Scale factor is active
View solution Code 61311
[Channel %1: ] Block %2: No D number active
View solution Code 61312
[Channel %1: ] Block %2: Check measuring cycle number
View solution Code 61313
[Channel %1: ] Block %2: Check probe number
View solution Code 61314
[Channel %1: ] Block %2: Check selected tool type
View solution Code 61315
[Channel %1: ] Block %2: Check position of cutting edge
View solution Code 61316
[Channel %1: ] Block %2: Center and radius cannot be determined
View solution Code 61317
[Channel %1: ] Block %2: Check number of circle calculation points
View solution Code 61318
[Channel %1: ] Block %2: Check weighting factor
View solution Code 61319
[Channel %1: ] Block %2: Check call parameter CYCLE114
View solution Code 61320
[Channel %1: ] Block %2: Check tool number
View solution Code 61321
[Channel %1: ] Block %2: Check WO memory number
View solution Code 61322
[Channel %1: ] Block %2: Check 4th digit of _KNUM
View solution Code 61323
[Channel %1: ] Block %2: Check 5th digit of _KNUM
View solution Code 61324
[Channel %1: ] Block %2: Check 6th digit of _KNUM
View solution Code 61325
[Channel %1: ] Block %2: Check measuring axis/offset axis
View solution Code 61326
[Channel %1: ] Block %2: Check measuring direction
View solution Code 61327
[Channel %1: ] Block %2 : Program reset required
View solution Code 61328
[Channel %1: ] Block %2: Check D number
View solution Code 61329
[Channel %1: ] Block %2: Check rotary axis
View solution Code 61330
[Channel %1: ] Block %2: Coordinate rotation active
View solution Code 61331
[Channel %1: ] Block %2: Angle too large, change measuring axis
View solution Code 61332
[Channel %1: ] Block %2: Modify tool tip position
View solution Code 61333
[Channel %1: ] Block %2: Check calibration block number
View solution Code 61334
[Channel %1: ] Block %2: Check safety area
View solution Code 61336
[Channel %1: ] Block %2: Geometry axes do not exist
View solution Code 61337
[Channel %1: ] Block %2: Check measuring input
View solution Code 61338
[Channel %1: ] Block %2: Positioning speed equal to zero
View solution Code 61339
[Channel %1: ] Block %2:Correction factor for rapid traverse speed = 0
View solution Code 61340
[Channel %1: ] Block %2 : Incorrect alarm number
View solution Code 61341
[Channel %1: ] Block %2: Probe not calibrated in active plane.
View solution Code 61342
[Channel %1: ] Block %2: Upgrade NCK software version
View solution Code 61343
[Channel %1: ] Block %2: No tool available for specified tool name
View solution Code 61344
[Channel %1: ] Block %2: Several tools are active
View solution Code 61345
[Channel %1: ] Block %2: D number of tool offset, too many digits
View solution Code 61346
[Channel %1: ] Block %2: Distance between starting point and measuring point <=0
View solution Code 61347
[Channel %1: ] Block %2: Angle 1st edge - 2nd edge equals 0
View solution Code 61348
[Channel %1: ] Block %2: Angle rel. to reference edge equals 0
View solution Code 61349
[Channel %1: ] Block %2: Distance upper probe edge - measuring position = 0 for tool radius measurement
View solution Code 61350
[Channel %1: ] Block %2: Feed, speed not programmed for tool measurement with rotating spindle
View solution Code 61351
[Channel %1: ] Block %2: Tool length or radius is 0
View solution Code 61352
[Channel %1: ] Block %2: Path for logfile not permitted
View solution Code 61353
[Channel %1: ] Block %2: Path for logfile not found
View solution Code 61354
[Channel %1: ] Block %2: File for logfile not found
View solution Code 61355
[Channel %1: ] Block %2: Incorrect file type for logfile
View solution Code 61356
[Channel %1: ] Block %2: File for logfile is being used
View solution Code 61357
[Channel %1: ] Block %2: No resources free
View solution Code 61358
[Channel %1: ] Block %2: Error during recording
View solution Code 61359
[Channel %1: ] Block %2 : - continue with RESET
View solution Code 61360
[Channel %1: ] Bloc k %2: Log job undefined - continue with RESET
View solution Code 61361
[Channel %1: ] Block %2: Variable cannot be recorded
View solution Code 61362
[Channel %1: ] Block %2: Cycle118: No. of values too large
View solution Code 61363
[Channel %1: ] Block %2: Max. no. of value lines for recording exceeded
View solution Code 61364
[Channel %1: ] Block %2: Check distance from measuring point 1 to measuring point 2
View solution Code 61365
[Channel %1: ] Block %2: Check circular feed
View solution Code 61366
[Channel %1: ] Block %2: Direction of rotation for tool measurement with rotating spindle not specified.
View solution Code 61367
[Channel %1: ] Block %2: Parameters _SETV[0...3] or _SETV[4...7] are identical
View solution Code 61368
[Channel %1: ] Block %2: Straights through parameter _SETV[0...3] or _SETV[4...7]do not intersect
View solution Code 61369
[Channel %1: ] Block %2: Position of corner not clearly definable, check parameter _SETV[0...7]
View solution Code 61370
[Channel %1: ] Block %2: _PROTVAL[0] -_PROTVAL[5] do not have any entries
View solution Code 61371
[Channel %1: ] Block %2: Product of column width and number of columns exceeds 200 characters per line
View solution Code 61372
[Channel %1: ] Block %2: selected meas.variant requires SPOS-capable spindle
View solution Code 61373
[Channel %1: ] Block %2: Mono-directional probe requires SPOS-capable spindle
View solution Code 61401
[Channel %1: ] Block %2: Probe does not switch, traversing path limited by software limit position.
View solution Code 61402
[Channel %1: ] Block %2: Probe col lision, traversing path limited by software limit position
View solution Code 61403
[Channel %1: ] Block %2: Work offset correction not executed
View solution Code 61404
[Channel %1: ] Block %2: Tool correction not executed
View solution Code 61405
[Channel %1: ] Block %2: Tool environment does not exist
View solution Code 61406
[Channel %1: ] Block %2: Check DL number
View solution Code 61407
[Channel %1: ] Block %2: Check 7th digit and higher of _KNUM
View solution Code 61408
[Channel %1: ] Block %2: total offsets not present
View solution Code 61409
[Channel %1: ] Block %2: set up offsets not present
View solution Code 61410
[Channel %1: ] Block %2 access to nonexistent tool element or property
View solution Code 61411
[Channel %1: ] Block %2: Check the distribution of measuring points on the plane.
View solution Code 61412
[Channel %1: ] Block %2: channel basic frame not present
View solution Code 61413
[Channel %1: ] Block %2: check setpoint of ball diameter, _SETVAL<=0
View solution Code 61414
[Channel %1: ] Block %2 : distortion of triangle over limit
View solution Code 61415
[Channel %1: ] Block %2: Check probe / machining plane
View solution Code 61416
[Channel %1: ] Block %2: adapt array size %4!
View solution Code 61417
[Channel %1: ] Block %2: Probe will collide with the carrier of the reference groove.
View solution Code 61418
[Channel %1: ] Block %2: Protocol file too small, check MD11420: LEN_PROTOCOL_FILE.
View solution Code 61419
[Channel %1: ] Block %2: Check probe calibration with reference to center of ball/circumference of ball.
View solution Code 61420
[Channel %1: ] Block %2: Check calibration of multi/mono probes.
View solution Code 61421
[Channel %1: ] Block %2: Software release of measuring cycles or NCK inadequate or set up inco rrectly --> error code %4
View solution Code 61422
[Channel %1: ] Block %2: Parameter _MVAR incorrect --> Error code: %4
View solution Code 61423
[Channel %1: ] Block %2: Parameter _TNUM not agreed or not created
View solution Code 61424
[Channel %1: ] Block %2: Parameter _SETVAL for diameter of calibration ball incorrect
View solution Code 61425
[Channel %1: ] Block %2: Parameter fo r measuring axis rotary axis 1 or 2 incorrect -> Error code: %4
View solution Code 61426
[Channel %1: ] Block %2: Sum of the active offsets does not equal zero - > Error code: %4
View solution Code 61427
[Channel %1: ] Block %2: Tool data of the active workpiece probe incorrect or inactive --> Error code: %4
View solution Code 61428
[Channel %1: ] Block %2: Error while creating log file -> Error code: %4
View solution Code 61429
[Channel %1: ] Block %2: Measuring axis (rotary axis 1 or 2) not in basic or intended position -> Error code: %4
View solution Code 61430
[Channel %1: ] Block %2: Kinematic vectors not computed -> Error code: %4
View solution Code 61440
[Channel %1: ] Block %2: Position of cutting edge cannot be determined
View solution Code 61441
[Channel %1: ] Block %2: Position of cutting edge is not in the machining plane.
View solution Code 61442
[Channel %1: ] Block %2: Tool carrier not parallel to the geometry axes
View solution Code 61443
[Channel %1: ] Block %2: Advance angle _INCA=0 or greater/less than +/- 90° or +/-120°
View solution Code 61444
[Channel %1: ] Block %2: Current measuring speed is not identical to the calibration speed
View solution Code 61501
[Channel %1: ] Block %2: Simulation is active
View solution Code 61502
[Channel %1: ] Block %2: No tool offset active
View solution Code 61503
[Channel %1: ] Block %2: tool nos e radius compensation left or right
View solution Code 61504
[Channel %1: ] Block %2: _KNG incorrect for setup
View solution Code 61505
[Channel %1: ] Block %2: retraction path < 1mm
View solution Code 61506
[Channel %1: ] Block %2: infeed path < 1mm
View solution Code 61507
[Channel %1: ] Block %2: safety clearance < 1mm
View solution Code 61508
[Channel %1: ] Block %2: Incorrect default setting for shoulder position
View solution Code 61509
[Channel %1: ] Block %2: Incorrect default setting for dresser position
View solution Code 61510
[Channel %1: ] Block %2: Test run feed is active
View solution Code 61511
[Channel %1: ] Block %2: Incorrect s houlder position or tool edge D1/D2
View solution Code 61512
[Channel %1: ] Block %2: Incorrect longitudinal position
View solution Code 61513
[Channel %1: ] Block %2: Dresser left and inclined grinding wheel
View solution Code 61514
[Channel %1: ] Block %2: Grinding wheel type missing
View solution Code 61515
[Channel %1: ] Block %2: Retraction path <= dressing amount
View solution Code 61517
[Channel %1: ] Block %2: Angle of inclined grinding wheel missing
View solution Code 61518
[Channel %1: ] Block %2: Shoulder height of grinding wheel must be > grinding wheel radius
View solution Code 61519
[Channel %1: ] Block %2: Incorrect type of machining
View solution Code 61520
[Channel %1: ] Block %2: Additional offsets not set
View solution Code 61521
[Channel %1: ] Block %2: Current grinding wheel too wide
View solution Code 61522
[Channel %1: ] Block %2: Overla p >= current grinding wheel width
View solution Code 61523
[Channel %1: ] Block %2: Zero signal of calipers missing
View solution Code 61524
[Channel %1: ] Block %2: Incorrect oblique angle
View solution Code 61525
[Channel %1: ] Block %2: Incorrect grinding wheel type
View solution Code 61526
[Channel %1: ] Block %2: Workpiece radius = 0
View solution Code 61527
[Channel %1: ] Block %2: Grindi ng wheel radius >= workpiece radius
View solution Code 61529
[Channel %1: ] Block %2: Dimensional notation INCH programmed
View solution Code 61530
[Channel %1: ] Block %2: Default longitudinal position incorrect
View solution Code 61531
[Channel %1: ] Block %2: Longitudinal position not registered in Z
View solution Code 61532
[Channel %1: ] Block %2: Value for _LAGE is incorrect
View solution Code 61533
[Channel %1: ] Block %2: No length L1 entered under D...
View solution Code 61540
[Channel %1: ] Block %2: Incorrect D number / dresser D field active
View solution Code 61541
[Channel %1: ] Block %2: Incorrect grinding wheel type entered
View solution Code 61542
[Channel %1: ] Block %2: Incorrect grinding wheel reference point selected when selecting the dresser coordinate system
View solution Code 61543
[Channel %1: ] Block %2: Incorrect dresser selected when selecting the dresser coordinate system
View solution Code 61544
[Channel %1: ] Block %2: Gri nding wheel diameter worn down
View solution Code 61545
[Channel %1: ] Block %2: Widt h of grinding wheel worn down
View solution Code 61546
[Channel %1: ] Block %2: Dresser %4, wear limit length 1 reached
View solution Code 61547
[Channel %1: ] Block %2: Dresser %4, wear limit length 2 reached
View solution Code 61548
[Channel %1: ] Block %2: Dresser %4, wear limit length 3 reached
View solution Code 61549
[Channel %1: ] Block %2: Incorrect dresser type selected
View solution Code 61555
[Channel %1: ] Block %2: Diameter of grinding wheel ==0, GWPS cannot be calculated
View solution Code 61556
[Channel %1: ] Block %2: Impossible chamfer and radius of left edge of wheel
View solution Code 61557
[Channel %1: ] Block %2: Impossible chamfer and radius of right edge of wheel
View solution Code 61558
[Channel %1: ] Block %2: Chamfer / radius + shoulder height are less than the retraction height of the left edge of the grinding wheel
View solution Code 61559
[Channel %1: ] Block %2: Chamfer / radius + shoulder height are less than the retraction height of the right edge of the grinding wheel
View solution Code 61560
[Channel %1: ] Block %2: Infeed in Z direction too big per stroke, or wheel too narrow
View solution Code 61561
[Channel %1: ] Block %2: Feed left wheel edge <=0
View solution Code 61562
[Channel %1: ] Block %2: Feed right wheel edge <=0
View solution Code 61563
[Channel %1: ] Block %2: Feed on the diameter <=0
View solution Code 61564
[Channel %1: ] Block %2: Feed insertion <=0
View solution Code 61565
[Channel %1: ] Block %2: Feed dressing <=0
View solution Code 61601
[Channel %1: ] Block %2: Finished part diameter too small
View solution Code 61602
[Channel %1: ] Block %2: Tool width incorrectly defined
View solution Code 61603
[Channel %1: ] Block %2: Recess type incorrectly defined
View solution Code 61604
[Channel %1: ] Block %2: Active tool violates programmed contour
View solution Code 61605
[Channel %1: ] Block %2: Contour incorrectly programmed
View solution Code 61606
[Channel %1: ] Block %2: Error during contour preparation
View solution Code 61607
[Channel %1: ] Block %2: Starting point incorrectly programmed
View solution Code 61608
[Channel %1: ] Block %2: Incorrect tool point direction programmed
View solution Code 61609
[Channel %1: ] Block %2: Shape incorrectly defined
View solution Code 61610
[Channel %1: ] Block %2: No infeed depth programmed
View solution Code 61611
[Channel %1: ] Block %2: No point of intersection found
View solution Code 61612
[Channel %1: ] Block %2: Thread finishing not possible
View solution Code 61613
[Channel %1: ] Block %2: Undercut position incorrectly defined
View solution Code 61700
[Channel %1: ] Block %2: Name of program to be generated is missing
View solution Code 61701
[Channel %1: ] Block %2: Contour %4 does not exist
View solution Code 61702
[Channel %1: ] Block %2: Label %4 not existing in machined part contour
View solution Code 61703
[Channel %1: ] Block %2: Label %4 not existing in the blank contour
View solution Code 61704
[Channel %1: ] Block %2: Machined part contour missing
View solution Code 61705
[Channel %1: ] Block %2: Blank contour missing
View solution Code 61706
[Channel %1: ] Block %2: Error in machined part contour %4
View solution Code 61707
[Channel %1: ] Block %2: Error in the blank contour %4
View solution Code 61708
[Channel %1: ] Block %2: Too many contours specified
View solution Code 61709
[Channel %1: ] Block %2: Cutting edge radius too small
View solution