Back to all Heidenhain models

Heidenhain TNC Series CNC

Heidenhain TNC Series CNC Error Codes

Complete alarm and error code reference for the Heidenhain TNC Series CNC. Browse all 4497 documented fault codes below, each linking to a detailed troubleshooting guide.

Search this section

Search Heidenhain TNC Series CNC

Search all 4497 Heidenhain TNC Series CNC codes without changing pages.

Search all database

Complete Alarm List (Page 14 of 23)

Plunging type is not possible

Plunge angle incorrectly defined

Angular length is undefined

Slot width is too large

Scaling factors not equal

Tool data inconsistent

MOVE not possible

Presetting not allowed!

Thread angle too small!

3-D ROT status is contradictory!

Configuration is incomplete

No turning tool is active

Tool orientation is inconsistent

Angle not possible!

Radius too small!

Thread runout too short!

Contradictory meas. points

Too many limits

Machining strategy with limits not possible

Machining direction not possible

Check the thread pitch!

Angle cannot be calculated

Eccentric turning not possible

No milling tool is active

Insufficient length of cutting edge

Gear definition is inconsistent or incomplete

No finishing allowance provided

Line does not exist in table

Probing process not possible

Coupling function not possible

Fixed cycle is not supported by this NC software

Touch probe cycle is not supported by this NC software

NC program aborted

Touch probe data incomplete

LAC function not possible

Rounding radius or chamfer is too large!

Axis angle not equal to tilt angle

Character height not defined

Excessive character height

Tolerance error: Workpiece rework

Tolerance error: Workpiece scrap

Faulty dimension definition

Illegal entry in compensation table

Transformation not possible

Tool spindle incorrectly configured

Offset of the turning spindle unknown

Global program settings are active

Faulty configuration of OEM macros

The combination of programmed oversizes is not possible

Measured value not captured

Check the monitoring of the tolerance

Hole is smaller than the stylus tip

Preset cannot be set

Alignment of a rotary table is not possible

Alignment of rotary axes is not possible

Infeed limited to length of cutting edge

Machining depth defined as 0

Tool type is unsuitable

Finishing allowance not defined

Machine datum could not be written

Spindle for synchronization could not be ascertained

Function is not possible in the active operating mode

Oversize defined too large

Number of teeth not defined

Machining depth does not increase monotonously

Infeed does not decrease monotonously

Tool radius not defined correctly

Mode for retraction to clearance height not possible

Gear wheel definition incorrect

Probing object contains different types of dimension defini-

Dimension definition contains impermissible characters

Actual value in dimension definition faulty

Starting point of hole too deep

Dimension def.: Nominal value missing for manual pre-

A replacement tool is not available

OEM macro is not defined

Measurement not possible with auxiliary axis

Start position not possible with modulo axis

Function only possible if door is closed

Number of possible records exceeded

Inconsistent machining plane due to axis angle with basic

Transfer parameter contains an impermissible value

Tooth width RCUTS is defined too large

Usable length LU of the tool is too small

The defined chamfer is too large

Chamfer angle cannot be machined with the active tool

The allowances do not define any stock removal

Spindle angle not unique

Internal software error: wrong or faulty command

Probing procedure is not possible

Type of the object to be probed is not possible

Input value not permitted

No data available for processing

Object to be probed cannot be repeated

Limitation for island missing

Cannot process the data

Rotation of the tool coordinate system not permitted

NC Start was ignored

Circle cannot be calculated

Probing of an extrusion not possible

Nominal position not defined correctly

Retraction behavior not possible with multiple plunging

Basic rotation will be rescinded

Repeat last measurement?

Continue with next measurement?

The entire plunging depth is greater than the tooth height

The entire plunging depth is less than the tooth height

File cannot be opened

Status of transformations for simultaneous turning is not

Preset cannot be modified after probe objects have been

Tolerance does not match probing direction

Offset in pallet reference point not permitted

Global program settings are active

Global program settings are active

Cycle can be executed only in the Testing mode

Tool carrier can't be monitored correctly

Probing function doesn't support stylus type

Slot smaller than stylus tip

Determination of machine datum with inclination angle not 0

Feed-rate potentiometer is effective for L stylus!

Spindle orientation not possible

Antastpunkt nicht erreicht

Starten eines Antast-Zyklus mit bereits ausgelenktem Taster

Keine gültige Zeile für einen Bezugspunkt

Error in pallet management

Error in pocket table

Fixture not activated

Pallet line locked!

Datum table missing

Measuring probe not defined

Incorrect tool data

Tool number 0 not permitted

Tool not defined

No appropriate tool found

Calculated tool number too large

Tool definition is missing

Tool number already assigned

Tool definition not permitted

TOOL DEF w/o length or radius

Max. tool age expired

Tool table is missing

Helical plunging not possible

No touch probe data

SQL command failed

Error in pallet management

Error in preset table

Incorrect datum table

Tool change during mid-program startup not possible

Calibrate touch probe

Tool axis is missing

CYCL DEF incomplete

TOOL.T: Enter number of teeth

Enter tool radius greater than 0

Tolerance in the parameter measureTolerance[1;2] is too low

Error in tool measurement configuration

Tool measurement locked

Tool measurement: Functionality not yet implemented

Orientation not configured

Arithmetical error

Calibrate TT in tilted plane

Calibrate TT in non-tilted plane

TT not parallel to tool axis

Tool index not allowed

Turning tool incompletely defined

Probing direction not in probe plane

Unbalance detection failed

Excessive unbalance

Configuration for unbalance detection wrong

Radius of replacement tool not suitable

Invalid tool axis programmed

Tool table locked

Unbalance calculation failed

Tool must not be altered

Traverse mode for retraction not possible

Tool life expired

Tool life expired

rate limiting has been canceled

Pallet line with completed part

Access to pallet preset table failed

Automatic continuation of pallet machining not possible

Strategy for continuing the pallet machining is not supported

Thread-cutting process was interrupted

Pallet table locked

Tool not defined completely

Row does not exist in preset table

Row does not exist in pallet preset table

Preset table not found

Camera not reacting

Camera not responding

2601-2800 of 4497