Back to all Heidenhain models

Heidenhain TNC Series CNC

Heidenhain TNC Series CNC Error Codes

Complete alarm and error code reference for the Heidenhain TNC Series CNC. Browse all 4497 documented fault codes below, each linking to a detailed troubleshooting guide.

Search this section

Search Heidenhain TNC Series CNC

Search all 4497 Heidenhain TNC Series CNC codes without changing pages.

Search all database

Complete Alarm List (Page 16 of 23)

FN22 command faulty

Parameter block does not exist

Command not allowed

Command not allowed at this point

Non-circular channel not active

Non-circ. channel still active

Command only allowed in non-circular channel

Incorrect contour command

Error in contour machining

Contour program faulty

Tool axis X, Y, Z permitted

Starting spindle angle missing

Max. tilt angle exceeded

Spindle speed not possible

Spindle speed not possible

Camera data faulty

Spindle angle unknown

Option for panorama image is missing

Error in VTC.TAB

Excessive number of teeth

Incorrect VTC API version

Impermissible character in job name

Incorrect value for contact angle at R2

Contact angle of 0 degrees is not permitted

Cycle cannot be used with drilling tools

Approaching/tilting to camera not possible

Value not in permitted range

Error in table VTC-TOOLS.TAB

Tool contact angle Q629 doesn't equal 0

Selection of view in Q622 doesn't equal 0

Calculation of wear on dressing tool not possible

Wear on dressing tool exceeds breakage tolerance

Look-ahead: internal software error

ProfilePool: internal software error

ProfilePool: internal software error

ProfilePool: internal software error

Look-ahead: internal software error

Thread cutting: Spindle synchronized too late

Axes switched while in motion

Incorrect sequence of contour machining

Parameters for contour machining not allowed

Clamping mode switched too early

System error: No feed rate

No spindle available for feed per revolution!

New start after immediate stop of noncylindr. contour not

Noncircular program too long for RAM

CMO is not in the current kinematic description

Tool is not monitored for collisions

Tool is not allowed for collision monitoring

General system error in the collision monitoring

Spindle turning too fast

DCM inactive: Axis has not yet been homed

DCM inactive: RTC (Real Time Coupling) activated

Axes have not been homed, although DCM is active

Lagged axes with active DCM

Thread cutting: Spindle synchronization aborted!

DCM inactive: Facing-slide kinematics are activated

Facing slide activated with active DCM

Deactivate handwheel for axis %1

Configuration of CfgDCM/manualModeDistance is faulty

Machine configuration is incorrect

Look-ahead: internal software error. Code %1

%3 3-D model not loaded %2

%3 3-D model not loaded %2

%3 3-D model not loaded %2

Internal error in Look-Ahead Chain Module

Illegal filter type 2

Axis %1 with 2 filters

Incorrect filter form in axis %1

No cutter-location filter active

Tolerance for rotary axes inactive

Axis parameters for logical axis %1 were lost

Parameters from another axis were programmed %1

Parameters from another axis were configured %1

Missing axis parameters in CfgAxis of %1

Two cutter-location filters

Position filter is missing

Two position filters in axis %1

No position filter in axis %1

The option for axis-specific jerk has not been enabled

The option for the feed rate filter has not been enabled

In Program Run it is not allowed to switch the filter on or off

Faulty configuration of the nominal position value filters

Name of parameter set (%1) for axis (%2) already assigned

Option for limiting the radial acceleration not enabled

Filter settings for virtual axis %1 not allowed

ADP must be active during use of DCM tolerances

Excessive contour error (%1 mm) in thread (%2 mm permit-

End of successive threads not reached

Invalid number programmed for FN17/18 No%1

Invalid axis programmed in FN17/18 IDX%1

Vertical movement not allowed in the middle of successive

Programmed feed rate too small

The NC program is longer than %1

Internal error in LookAheadChain module. Code %1

Impermissible dynamic calculation of non-registered axis %1

NC program contains more than %1 blocks

Process monitoring recordings are not compatible

Process monitoring recordings are not compatible

Process Monitoring export: memory limit almost reached.

Not enough free hard disk space for Process Monitoring

Manufacturer texts for component monitoring are missing

Start of Python script "%1" failed

Referenced OPC UA namespace %1 does not exist

Referenced OPC UA parent node %1 does not exist

Invalid value for nodeIdIdentifier %1

Invalid value for publicationDate %1

Multiple definitions of the namespace URI %1

Value not permitted for namespaceUri %1

Multiple use of NodeId %1

Attribute %1 was not configured

Cyclic parent-child relationship

Invalid namespace URI %1

Invalid parent node: %1

Impermissible multiple use of browseName %1

More than %1 variables are configured

The configuration of the OPC UA NC Server has changed

Invalid range specified %1

Incomplete range specified %1

EURange outside of InstrumentRange

Unknown UnitCode %1

3001-3200 of 4497