Back to all Heidenhain models

Heidenhain TNC Series CNC

Heidenhain TNC Series CNC Error Codes

Complete alarm and error code reference for the Heidenhain TNC Series CNC. Browse all 4497 documented fault codes below, each linking to a detailed troubleshooting guide.

Search this section

Search Heidenhain TNC Series CNC

Search all 4497 Heidenhain TNC Series CNC codes without changing pages.

Search all database

Complete Alarm List (Page 6 of 23)

Formula in offsetForM19 invalid

Error in initialization of touch probe

Excessive servo lag in %2

Excessive following error in %2

Position encoder %2: Amplitude too small

Position encoder %2: Frequency too high

Error in zero pulse distance of encoder %2

Position encoder %2 defective

Error in zero pulse distance of encoder %2

Nominal speed value too high %2

Movement monitoring error in %2

Standstill monitoring err. in %2

%2 does not attain the control window

Following error in switched-off axis (%2) is too large

Probe system not ready

Exchange touch probe battery

CC index for %1 too large

Axis index on CC too large

Input for position encoder (%1) not found

EnDat encoder (%2) reports error

Absolute actual position of the axis (%2) not confirmed

EnDat encoder (%2) reports different resolution

EnDat encoder (%2) reports wrong position

%2 does not attain the programmed speed

Drive to be moved (%2) is not switched on.

Drive to be moved (%2) is not in the position loop

Deviation in the switch-on position of axis %2 too large

Hardware description for axis %2 has changed

Error in encoder configuration of axis %1

Error in spindle positioning (%2)

MC software does not match CC software

Configuration of digital axes not possible without CC

S-RAM contents of axis %2 are invalid.

Maximum traverse range of EnDat axis was exceeded.

The maximum traverse range of the EnDat axis was exceed-

%2 synchronous window not reached

The encoder of an axis in the position control loop must not

Two encoders with EnDat interface cannot be used for one

Input X%2 for axis %3 is already assigned to another axis.

Input X%2 for axis %3 is already assigned to another axis.

Input X%2 for axis %3 is already assigned to another axis.

Error during control of an SPI module

Spindle (%2) has no position encoder

AxisMode and AxisHw for axis (%2) do not match

Encoder type not permitted for axis (%2)

Analog output of axis %2 was assigned twice

Unknown touch probe model designation

Spindle (%2) has not yet been homed

EMERGENCY STOP defective (%2)

Relay ext. dc voltage missing

After SW download, CC no longer responds

The option for double-speed control loops has not been

Communication between MC and CC is faulty

Timeout during command processing by the CC

Option for master-slave torque control not enabled

Switch off after NC stop due to error %2

Output of axis %2 was assigned twice

Input of axis %2 was assigned twice

Incorrect connector assignment of the axis %2

Machine parameters were changed through TNCOPT

Switch off after NC stop due to error %2

Probe cycle started with stylus already deflected

LookAhead: Time out

High-speed inputs were incorrectly configured

Client with this thread ID is already logged on with CfgServer.

Configuration server not ready

Missing entity (%2) in configuration data

Missing entity (%2) in configuration data for axis %3

Power module %2 not found in table

Power module table cannot be read

Motor (%2) not found in motor table

Motor table (%2) cannot be read

No connection to the SQL server

Axis (%2) not found in compensation table

Syntax error in compensation table (%2)

Compensation table (%2) cannot be read

Parameter block name (%2) for axis (%3) is already assigned

Too many parameter blocks for axis %2

Shut down the control and restart after you delete an entity

Positioning of axis %2 was stopped due to reconfiguration.

Timeout while stopping axis %2

A spindle must be configured as a modulo axis (axis %2)

Fatal configuration error: Cycle machining has been stopped

Name (%2) for axis (%3) is invalid

Invalid configuration for axis %2

Fatal error in interpolator: Cyclic machining has been

Supply module %2 not found in table

Supply-module table cannot be read

No oriented spindle stop of homed spindle

Stylus already in contact

Velocity programmed for axis %2 too low

Rotational speed programmed for spindle ("%2") too low

Return to contour in thread cycle not allowed.

The option for HSC filter has not been enabled

Software option 151 Load Monitoring not enabled

Option for digital control loops not enabled

Plug & Play (%2) Motor detected: %3

Plug & Play (%2) Inverter detected: %3

Plug & Play (%2) Supply Module detected: %3

Axis %1 (%2): Motor %3 detected and registered

Axis %1 (%2): Inverter %3 detected and registered

Axis %1 (%2): Supply module %3 detected and registered

Axis %1 (%2): Plug & play has been deactivated for the motor

Axis %1 (%2): Plug & play has been deactivated for the invert-

Axis %1 (%2): Plug & play has been deactivated for supply

The current monitoring section will not be recorded.

Position error (axis %2) too large

Axis %2 cannot be switched on

Error bit in safety status (S status) of the HSCI transmission

TRC: Wrong control; axis %1

TRC: Compensation file (%1) illegible

Error in parameter posEncoderIncr or posEncoderDist (axis

No field angle for drive %1

MCU/CCU watchdog mismatch

Axis motion not allowed while the filter is being changed

Error in configuration of axis %2

Unbalance monitoring: measurement not possible

Unbalance monitoring (user): unbalance too large

Unbalance monitoring (user): sum of unbalance too large

Unbalance monitoring (system): unbalance too large

Unbalance monitoring (system): sum of unbalance too large

Unbalance monitoring: configuration missing

Unbalance monitoring: invalid spindle defined

Unbalance monitoring: invalid meas. axis defined

Unbalance monitoring: system monitor is not active

Unbalance monitoring: spindle is not configured

Unbalance monitoring: spindle parameter or index is faulty

Unbalance monitoring: limit speed has been reached

Unbalance trace: internal error

Unbalance trace: trigger timeout

Unbalance trace: internal error

Unbalance trace: spindle index refers to an incorrect axis

Unbalance trace: machine parameters not defined

Unbalance trace: internal error

Unbalance trace: incorrect spindle index

Unbalance trace: axis for measurement not defined

Unbalance trace: spindle is not configured

Unbalance trace: specified trigger axis does not exist

Unbalance trace: trigger conditions are not fulfilled

Unbalance monitoring: permissible unbalance not defined

Unbalance monitoring: permissible unbalance sum not

Unbalance monitoring: permissible unbalance not defined

Unbalance monitoring: permissible unbalance sum not

Real-time-buffer transfer from integr. oscill. is beginning

Internal error in transmission of oscilloscope measured data

Progmmd. limit switch/protection zone incorrect for axis %2

Handwheel superimposition not allowed (M118)

Collision monitoring not possible in turning mode

Velocity error (axis %2) too great

Internal error while processing the oscilloscope measuring

Internal error while processing the oscilloscope measuring

Internal error while processing the oscilloscope measuring

Handwheel: wrong handwheel connected

Handwheel: Contaminated or damaged

Handwheel: Transmission disturbance

Handwheel: Transmission error

Handwheel: Wrong parameter

Handwheel: Timeout

Handwheel: No connection possible

Axis %2: Enter CfgReferencing/doubleRefOffset: %3

PLC movement for axis %2 not allowed

DCM: No manual movement allowed during a program run

DCM: Program start or continuation not possible

DCM: No TCPM allowed during active DCM

DCM: Motion of the floating tap holder is not monitored

DCM not possible in following error mode or semifeedfor-

Reference mark not found

DCM: Check the skipReferencing parameter

S-RAM contents of axis %2 are inconsistent

DCM: Activation during a movement

S-RAM contents of axis %2 overwritten with values from file

Axis %2: CfgReferencing/doubleRefOffset: %3 was entered

Oscilloscope active during start of reference machining

Programmed movement not allowed

Error in configuration of axis %2

Configuration of kinematic compensation is faulty

Temperature compensation is faulty

Kinematic compensation is faulty

EnDat multiturn counter of the %2 axis was corrected

EnDat multiturn counter of the %2 axis was changed

The KinematicsComp option has not been enabled

Max. compensation value %2 reached in CfgKinSimpleTrans

Max. compensation value %2 reached in axis %1 component

More than %2 fast PLC inputs defined

Fast PLC input on impermissible bus system

Fast PLC inputs with more than one definition

Input for axis group enabling has incorrect parameters

Multiple inputs defined for axis group enabling %2

Input for axis group enabling %s on impermissible bus

Fast input for spindle has incorrect parameters

Several fast inputs defined for spindle %2

Fast input for spindle %1 on impermissible bus system

Fast input cannot be activated

Inputs for axis group enabling have multiple definitions

Fast input for spindle %2 already defined

TRC: The identification was adapted; axis %1; file %2

No fast input for spindle %2 (%3)

1001-1200 of 4497