代碼 201330: <location>Topology: Quick commissioning not possible

Message value: Fault cause: %1, supplementary informat ion: %2, preliminary component number: %3 Drive object: All objects Reaction: NONE Acknowledge: NONE Cause: Unable to carry out a quick commissioning. The exis ting actual topology does not fulfill the requirements. Alarm value (r2124, interpret hexadecimal): ccccbbaa hex: cccc = preliminary component number, bb = supplementary information, aa = fault cause aa = 01 hex = 1 dec: On one component illegal connections were detected. - bb = 01 hex = 1 dec: For a Motor Module, more than one motor with DRIVE-CLiQ was detected. - bb = 02 hex = 2 dec: For a motor with DRIVE-CLiQ, the DRIVE-CLiQ cable is not connected to a Motor Module. aa = 02 hex = 2 dec: The topology contains too many components of a particular type. - bb = 01 hex = 1 dec: There is more than one master Control Unit. - bb = 02 hex = 2 dec: There is more than 1 inf eed (8 for a parallel circuit configuration). - bb = 03 hex = 3 dec: There are more than 10 Motor M odules (8 for a parallel circuit configuration). - bb = 04 hex = 4 dec: There are more than 9 encoders. - bb = 05 hex = 5 dec: There are more than 8 Terminal Modules. - bb = 07 hex = 7 dec: Unknown component type - bb = 08 hex = 8 dec: There are more than 6 drive slaves. - bb = 09 hex = 9 dec: Connection of a drive slave not permitted. - bb = 0a hex = 10 dec: There is no drive master. - bb = 0b hex = 11 dec: There is more than one motor with DRIVE-CLiQ for a parallel circuit. - cccc: Not used. SINAMICS-Alarms aa = 03 hex = 3 dec: More than 16 components are connected at a DRIVE-CLiQ socket of the Control Unit. - bb = 0, 1, 2, 3 means e.g. detected at the DRIVE-CLiQ socket X100, X101, X102, X103. - cccc: Not used. aa = 04 hex = 4 dec: The number of components connected one after the other is greater than 125. - bb: Not used. - cccc = preliminary component number of the first component and component that resulted in the fault. aa = 05 hex = 5 dec: The component is not permissible for SERVO. - bb = 01 hex = 1 dec: SINAMICS G available. - bb = 02 hex = 2 dec: Chassis available. - cccc = preliminary component number of the first component and component that resulted in the fault. aa = 06 hex = 6 dec: On one component illegal EEPROM data was detected. These must be corrected before the system continues to boot. - bb = 01 hex = 1 dec: The Order No. [MLFB] of th e power unit that was replaced includes a space retainer. The space retainer (*) must be replaced by a correct character. - cccc = preliminary component number of the component with illegal EEPROM data. aa = 07 hex = 7 dec: The actual topology contains an illegal combination of components. - bb = 01 hex = 1 dec: Active Line M odule (ALM) and Basic Line Module (BLM). - bb = 02 hex = 2 dec: Active Line M odule (ALM) and Smart Line Module (SLM). - bb = 03 hex = 3 dec: SIMOTION control (e.g. SIMOTION D445) and SINUMERIK component (e.g. NX15). - bb = 04 hex = 4 dec: SINUMERIK control (e.g. SINUMERIK 730.net) and SIMOTION component (e.g. CX32). - cccc: Not used. Note: Connection type and connection number are described in F01375. See also: p0097 (Select drive object type), r0098 (Actual device topology), p0099 (Device target topology) Remedy: - adapt the output topology to the permissible requirements. - carry out commissioning using the commissioning software. - for motors with DRIVE-CLiQ, connect the power and DRIVE-CLiQ cable to the same Motor Module (Single Motor Module: DRIVE-CLiQ at X202, Doubl e Motor Module: DRIVE-CLiQ from motor 1 (X1) to X202, from motor 2 (X2) to X203). Re aa = 06 hex = 6 dec and bb = 01 hex = 1 dec: Correct the order number when commissi oning using the commissioning software. See also: p0097 (Select drive object type), r0098 (Actual device topology), p0099 (Device target topology)