Volver a todos los modelos de Siemens Search all database
Siemens SINUMERIK 840D CNC
Códigos de error de Siemens SINUMERIK 840D CNC
Referencia completa de códigos de alarma y error para Siemens SINUMERIK 840D CNC. Explore a continuación los 4014 códigos de falla documentados, cada uno con un enlace a una guía detallada de solución de problemas.
Search this section
Search Siemens SINUMERIK 840D CNC
Search all 4014 Siemens SINUMERIK 840D CNC codes without changing pages.
Lista completa de alarmas (Page 16 of 21)
Código 202152
<location>OA: Insufficient memory
Ver solución Código 203500
<location>TM: Initialization
Ver solución Código 203501
<location>TM: Sampling time change
Ver solución Código 203505
<location>TM: Analog input wire breakage
Ver solución Código 203506
<location>24 V power supply missing
Ver solución Código 203550
<location>TM: Speed setpoint filter natural frequency > Shannon frequency
Ver solución Código 203590
<location>TM: Module not ready
Ver solución Código 205000
<location>Power unit: Heat sink overtemperature
Ver solución Código 205001
<location>Power unit: Chip overtemperature
Ver solución Código 205002
<location>Power unit: Air intake overtemperature
Ver solución Código 205003
<location>Power unit: Elec tronics board overtemperature
Ver solución Código 205004
<location>Power unit: Rectifier overtemperature
Ver solución Código 205005
<location>Cooling system: Cooling medium flow rate too low
Ver solución Código 205006
<location>Power unit: Overtemperature thermal model
Ver solución Código 205007
<location>Power unit: Overtemperature thermal model (chassis PU)
Ver solución Código 205050
<location>Parallel circuit: Pulse enable in spite of pulse inhibit
Ver solución Código 205051
<location>Parallel circuit: Power unit pulse enable missing
Ver solución Código 205052
<location>Parallel circuit: Illegal current dissymmetry
Ver solución Código 205053
<location>Parallel circuit: Inadmi ssible DC link vo ltage dissymmetry
Ver solución Código 205054
<location>Parallel circ uit: Power unit de-activated
Ver solución Código 205055
<location>Power circuit: Power units with different code numbers
Ver solución Código 205056
<location>Parallel circuit: Power unit EPROM versions differ
Ver solución Código 205057
<location>Parallel circuit: Power unit firmware versions differ
Ver solución Código 205058
<location>Parallel circui t: VSM EEPROM versions differ
Ver solución Código 205059
<location>Parallel circuit: VSM firmware versions differ
Ver solución Código 205060
<location>Parallel circuit: Powe r unit firmware version does not match
Ver solución Código 205061
<location>Infeed, number of VSM
Ver solución Código 206000
<location>Infeed: Precharg ing monitoring time expired
Ver solución Código 206010
<location>Infeed: Power unit EP 24 V missing in operation
Ver solución Código 206050
<location>Infeed: Smart Mode not supported
Ver solución Código 206052
<location>Infeed: Filter temperature evaluation not supported
Ver solución Código 206100
<location>Infeed: Shutdown due to line supply undervoltage condition
Ver solución Código 206105
<location>Infeed: Line supply undervoltage
Ver solución Código 206200
<location>Infeed: Failure of one or several line phases
Ver solución Código 206205
<location>Infeed: Voltage dip in at least one line supply phase
Ver solución Código 206207
<location>Infeed: Line currents not symmetrical
Ver solución Código 206210
<location>Infeed: Summation current too high
Ver solución Código 206215
<location>Infeed: Summation current too high
Ver solución Código 206250
<location>Infeed: Defective capacitor(s) in at least one phase of line filter
Ver solución Código 206260
<location>Infeed: Temperature in the line filter too high
Ver solución Código 206261
<location>Infeed: Temperature in the line filter permanently too high
Ver solución Código 206262
<location>Infeed: Temperature switch in the line filter open when powering up
Ver solución Código 206300
<location>Infeed: Line voltage too high at power on
Ver solución Código 206301
<location>Infeed: Line supply overvoltage
Ver solución Código 206310
<location>Infeed: Supply voltage (p0210) incorrectly parameterized
Ver solución Código 206311
<location>Infeed: Supply voltage (p0210) incorrect
Ver solución Código 206320
<location>Master/slave: 4-channel multiplexer control not valid
Ver solución Código 206321
<location>Master/slave: 6-channel multiplexer control not valid
Ver solución Código 206350
<location>Infeed: Measured line frequency too high
Ver solución Código 206351
<location>Infeed: Measured line frequency too low
Ver solución Código 206400
<location>Infeed: Line supply data identification selected/active
Ver solución Código 206500
<location>Infeed: Line synchronization not possible
Ver solución Código 206601
<location>Infeed: Current offset measurement interrupted
Ver solución Código 206602
<location>Infeed: Current offset measurement not possible
Ver solución Código 206700
<location>Infeed: Switch line contactor for load condition
Ver solución Código 206800
<location>Infeed: Maximum steady-state DC link voltage reached
Ver solución Código 206810
<location>Infeed: DC link voltage alarm threshold
Ver solución Código 206900
<location>Braking Mo dule: Fault (1 -> 0)
Ver solución Código 206901
<location>Braking Module: Pre-alarm I2t shutdown
Ver solución Código 206904
<location>Braking Module internal is inhibited
Ver solución Código 206905
<location>Braking Module internal I2t shutdown alarm
Ver solución Código 206906
<location>Braking Module internal fault
Ver solución Código 206907
<location>Braking Module internal overtemperature
Ver solución Código 206908
<location>Braking Module internal shutdown due to overtemperature
Ver solución Código 206909
<location>Braking Module internal Vce fault
Ver solución Código 207011
<location>Drive: Motor overtemperature
Ver solución Código 207012
<location>Drive: I2t motor model overtemperature
Ver solución Código 207015
<location>Drive: Motor temperature sensor alarm
Ver solución Código 207016
<location>Drive: Motor temperature sensor fault
Ver solución Código 207080
<location>Drive: Incorrect control parameter
Ver solución Código 207082
<location>Macro: Execution not possible
Ver solución Código 207083
<location>Macro: ACX file not found
Ver solución Código 207084
<location>Macro: Condition for WaitUntil not fulfilled
Ver solución Código 207085
<location>Drive: Open-loop/closed-loop control parameters changed
Ver solución Código 207086
<location>Units changeover: Parameter limit violation due to reference value change
Ver solución Código 207087
<location>Drive: Encoderless oper ation not possible for the selected pulse frequency
Ver solución Código 207088
<location>Units changeover: Parameter limit violation due to units changeover
Ver solución Código 207089
<location>Changing over units: Adding a function module blocked if units changed over
Ver solución Código 207090
<location>Drive: Upper torque limit less than the lower torque limit
Ver solución Código 207100
<location>Drive: Sampling times cannot be reset
Ver solución Código 207110
<location>Drive: Sampling time s and basic clock cycle do not match
Ver solución Código 207200
<location>Drive: Master control ON/OFF1 command present
Ver solución Código 207210
<location>Master control PC/AOP inhibited
Ver solución Código 207220
<location>Drive: Master control by PLC missing
Ver solución Código 207300
<location>Drive: Line contactor feedback signal missing
Ver solución Código 207311
<location>Bypass motor switch
Ver solución Código 207312
<location>Bypass LSS:
Ver solución Código 207320
<location>Drive: Automatic restart interrupted
Ver solución Código 207321
<location>Drive: Automatic restart active
Ver solución Código 207329
<location>Drive: kT estimator, kT(iq) characteristic or voltage compensation does not function
Ver solución Código 207330
<location>Flying restart: Measured search current too low
Ver solución Código 207331
<location>FlyRestart: Not supported
Ver solución Código 207350
<location>Drive: Measuring prob e parameterized to a digital output
Ver solución Código 207400
<location>Drive: DC link voltage maximum controller active
Ver solución Código 207401
<location>Drive: DC link voltage maximum controller de-activated
Ver solución Código 207402
<location>Drive: DC link voltage minimum controller active
Ver solución Código 207403
<location>Drive: Lower DC link voltage threshold reached
Ver solución Código 207404
<location>Drive: Upper DC link voltage threshold reached
Ver solución Código 207405
<location>Drive: Kinetic buffering minimum speed not reached
Ver solución Código 207406
<location>Drive: Kinetic buf fering maximum time exceeded
Ver solución Código 207409
<location>Drive: V/f control, current limiting controller active
Ver solución Código 207410
<location>Drive: Current controller output limited
Ver solución Código 207411
<location>Drive: Flux controller output limited
Ver solución Código 207412
<location>Drive: Commutation angle incorrect (motor model)
Ver solución Código 207413
<location>Drive: Commutation angle incorrect (pole position identification)
Ver solución Código 207414
<location>Drive: Encoder serial number changed
Ver solución Código 207415
<location>Drive: Angular commutation offset transfer running
Ver solución Código 207416
<location>Drive: Flux controller configuration
Ver solución Código 207420
<location>Drive: Current setpoint filter natural frequency > Shannon frequency
Ver solución Código 207421
<location>Drive: Speed setpoint filter natural frequency > Shannon frequency
Ver solución Código 207422
<location>Drive: Reference model natural frequency > Shannon frequency
Ver solución Código 207423
<location>Drive: APC filter natural frequency > Shannon frequency
Ver solución Código 207424
<location>Drive: Operating condition for APC not valid
Ver solución Código 207425
<location>Drive: APC monitoring time for speed limit expired
Ver solución Código 207429
<location>Drive: DSC without encoder not possible
Ver solución Código 207430
<location>Drive: Changeover to ope n-loop torque controlled operation not possible
Ver solución Código 207431
<location>Drive: Changeover to encoderless operation not possible
Ver solución Código 207432
<location>Drive: Synchronous motor without overvoltage protection
Ver solución Código 207433
<location>Drive: Closed-loop control with encoder is not possible as the encoder has not been unparked
Ver solución Código 207434
<location>Drive: It is not possible to change the direction of rotation with the pulses enabled
Ver solución Código 207435
<location>Drive: Setting the ramp-function generator for sensorless vector control
Ver solución Código 207440
<location>EPOS: Jerk time is limited
Ver solución Código 207441
<location>LR: Save the position offset of the absolute encoder adjustment
Ver solución Código 207442
<location>LR: Multiturn does not match the modulo range
Ver solución Código 207443
<location>LR: Reference point coordinate not in the permissible range
Ver solución Código 207446
<location>Load gear: Position tracking cannot be reset
Ver solución Código 207447
<location>Load gear: Position trac king, maximum actual value exceeded
Ver solución Código 207448
<location>Load gear: Position trac king, linear axis has exceeded the maximum range
Ver solución Código 207449
<location>Load gear: Position tracking, current position outside tolerance window
Ver solución Código 207450
<location>LR: Standstill monitoring has responded
Ver solución Código 207451
<location>LR: Position monitoring has responded
Ver solución Código 207452
<location>LR: Following error too high
Ver solución Código 207453
<location>LR: Position actu al value preprocessing error
Ver solución Código 207454
<location>LR: Position actual value preprocessing does not have a valid encoder
Ver solución Código 207455
<location>EPOS: Maximum velocity limited
Ver solución Código 207456
<location>EPOS: Setpoint velocity limited
Ver solución Código 207457
<location>EPOS: Combination of input signals illegal
Ver solución Código 207458
<location>EPOS: Reference cam not found
Ver solución Código 207459
<location>EPOS: No zero mark
Ver solución Código 207460
<location>EPOS: End of reference cam not found
Ver solución Código 207461
<location>EPOS: Reference point not set
Ver solución Código 207462
<location>EPOS: Selected traversing block number does not exist
Ver solución Código 207463
<location>EPOS: External block change not requested in the traversing block
Ver solución Código 207464
<location>EPOS: Traversing block is inconsistent
Ver solución Código 207465
<location>EPOS: Traversing block does not have a subsequent block
Ver solución Código 207466
<location>EPOS: Traversing block number assigned a multiple number of times
Ver solución Código 207467
<location>EPOS: Traversing block has illegal task parameters
Ver solución Código 207468
<location>EPOS: Traversing block jump destination does not exist
Ver solución Código 207469
<location>EPOS: Traversing block < target position < software limit switch minus
Ver solución Código 207470
<location>EPOS: Traversing block> target position > software limit switch plus
Ver solución Código 207471
<location>EPOS: Traversing block target position outside the modulo range
Ver solución Código 207472
<location>EPOS: Traversing bl ock ABS_POS/ABS_NEG not possible
Ver solución Código 207473
<location>EPOS: Beginning of traversing range reached
Ver solución Código 207474
<location>EPOS: End of traversing range reached
Ver solución Código 207475
<location>EPOS: Target position < start of traversing range
Ver solución Código 207476
<location>EPOS: Target position > end of the traversing range
Ver solución Código 207477
<location>EPOS: Target positio n < software limit switch minus
Ver solución Código 207478
<location>EPOS: Target positio n > software limit switch plus
Ver solución Código 207479
<location>EPOS: Software limit switch minus reached
Ver solución Código 207480
<location>EPOS: Software limit switch plus reached
Ver solución Código 207481
<location>EPOS: Axis positi on < software limit switch minus
Ver solución Código 207482
<location>EPOS: Axis positi on > software limit switch plus
Ver solución Código 207483
<location>EPOS: Travel to fixed stop clamping torque not reached
Ver solución Código 207484
<location>EPOS: Fixed stop outside the monitoring window
Ver solución Código 207485
<location>EPOS: Fixed stop not reached
Ver solución Código 207486
<location>EPOS: Intermediate stop missing
Ver solución Código 207487
<location>EPOS: Reject traversing task missing
Ver solución Código 207488
<location>EPOS: Relative positioning not possible
Ver solución Código 207489
<location>EPOS: Reference point correction outside the window
Ver solución Código 207490
<location>EPOS: Enable signal withdrawn while traversing
Ver solución Código 207491
<location>EPOS: STOP cam minus reached
Ver solución Código 207492
<location>EPOS: STOP cam plus reached
Ver solución Código 207493
<location>LR: Overflow of the value range for position actual value
Ver solución Código 207494
<location>LR: Drive Data Set changeover in operation
Ver solución Código 207495
<location>LR: Reference function interrupted
Ver solución Código 207496
<location>EPOS: Enable not possible
Ver solución Código 207497
<location>LR: Position setting value activated
Ver solución Código 207498
<location>LR: Measuring pr obe evaluation not possible
Ver solución Código 207499
<location>EPOS: Reversing cam approached with the incorrect traversing direction
Ver solución Código 207500
<location>Drive: Power unit data set PDS not configured
Ver solución Código 207501
<location>Drive: Motor Data Set MDS not configured
Ver solución Código 207502
<location>Drive: Encoder Data Set EDS not configured
Ver solución Código 207504
<location>Drive: Motor data set is not assigned to a drive data set
Ver solución Código 207509
<location>Drive: Component number missing
Ver solución Código 207510
<location>Drive: Identical encoder in the drive data set
Ver solución Código 207511
<location>Drive: Encoder used a multiple number of times
Ver solución Código 207512
<location>Drive: Encoder data set changeover cannot be parameterized
Ver solución Código 207514
<location>Drive: Data structure does not correspond to the interface module
Ver solución Código 207515
<location>Drive: Power unit and motor incorrectly connected
Ver solución Código 207516
<location>Drive: Re-commission the data set
Ver solución Código 207517
<location>Drive: Encoder data set changeover incorrectly parameterized
Ver solución Código 207518
<location>Drive: Motor data set changeover incorrectly parameterized
Ver solución Código 207519
<location>Drive: Motor changeover incorrectly parameterized
Ver solución Código 207520
<location>Drive: Motor cannot be changed over
Ver solución Código 207530
<location>Drive: Drive Data Set DDS not present
Ver solución Código 207541
<location>Drive: Data set changeover not possible
Ver solución Código 207550
<location>Drive: Not possible to reset encoder parameters
Ver solución Código 207551
<location>Drive encoder: No commutation angle information
Ver solución Código 207552
<location>Drive encoder: Encoder configuration not supported
Ver solución Código 207553
<location>Drive encoder: Sensor Module configuration not supported
Ver solución