Volver a todos los modelos de Siemens Search all database
Siemens SINUMERIK 840D CNC
Códigos de error de Siemens SINUMERIK 840D CNC
Referencia completa de códigos de alarma y error para Siemens SINUMERIK 840D CNC. Explore a continuación los 4014 códigos de falla documentados, cada uno con un enlace a una guía detallada de solución de problemas.
Search this section
Search Siemens SINUMERIK 840D CNC
Search all 4014 Siemens SINUMERIK 840D CNC codes without changing pages.
Lista completa de alarmas (Page 4 of 21)
Código 14182
[Channel %1: ] Block %2 different values under H and D addresses
Ver solución Código 14183
[Channel %1: ] Block %2 H and D addresses must be programmed after Siemens offset
Ver solución Código 14184
[Channel %1: ] Block %2 G44 is not possible with tool offset H99
Ver solución Código 14185
[Channel %1: ] Block %2 D number %3 is not defined
Ver solución Código 14186
[Channel %1: ] Block %2 ISO2 mode, and toolcarrier or tool adapter are both active (identifier %3)
Ver solución Código 14190
[Channel %1: ] Block %2 H number with G49
Ver solución Código 14195
[Channel %1: ] Block %2 D number with G49
Ver solución Código 14196
[Channel %1: ] Block %2 error %3 on interpreting the contents of $SC_CUTDIRMOD
Ver solución Código 14197
[Channel %1: ] Block %2 D number and H number programmed simultaneously
Ver solución Código 14198
[Channel %1: ] Block %2 illegal change of tool direction with tool offset
Ver solución Código 14199
[Channel %1: ] Block %2 illegal plane change for tool with diameter component
Ver solución Código 14200
[Channel %1: ] Block %2 negative polar radius
Ver solución Código 14210
[Channel %1: ] Block %2 polar angle too large
Ver solución Código 14250
[Channel %1: ] Block %2 negative pole radius
Ver solución Código 14260
[Channel %1: ] Block %2 pole angle too large
Ver solución Código 14270
[Channel %1: ] Block %2 pole programmed incorrectly
Ver solución Código 14280
[Channel %1: ] Block %2 polar coordinates programmed incorrectly
Ver solución Código 14290
[Channel %1: ] Block %2 polynominal degree greater than 5 programmed for polynominal interpolation
Ver solución Código 14300
[Channel %1: ] Block %2 overlaid handwheel motion activated incorrectly
Ver solución Código 14320
[Channel %3: ] Axis %4: handwheel %1 used twice (%2)
Ver solución Código 14400
[Channel %1: ] Block %2 tool radius compensation active at transformation switchover
Ver solución Código 14401
[Channel %1: ] Block %2 transformation not available
Ver solución Código 14402
[Channel %1: ] Block %2 spline active at transformation change
Ver solución Código 14403
[Channel %1: ] Block %2 preprocessing and main run might not be synchronized
Ver solución Código 14404
[Channel %1: ] Block %2 illegal parameterization of transformation
Ver solución Código 14410
[Channel %1: ] Block %2 spline active at geometry axis changeover
Ver solución Código 14411
[Channel %1: ] Block %2 tool radius compensation active at geometry axis changeover
Ver solución Código 14412
[Channel %1: ] Block %2 transformation active at geometry axis changeover
Ver solución Código 14413
[Channel %1: ] Block %2 fine tool correction: changeover geometry/channel axis not allowed
Ver solución Código 14414
[Channel %1: ] Block %2 GEOAX function: incorrect call
Ver solución Código 14415
[Channel %1: ] Block %2 tangent control: changeover geometry/channel axis not allowed
Ver solución Código 14420
[Channel %1: ] Block %2 index axis %3 frame not allowed
Ver solución Código 14430
[Channel %1: ] Block %2 tangential axis %3 must not be traversed as POS axis
Ver solución Código 14432
[Channel %1: ] Block %2 rounding length for tangential axis %3 is zero.
Ver solución Código 14434
[Channel %1: ] Block %2 rel. lift-off path for tangential axis %3 is invalid
Ver solución Código 14500
[Channel %1: ] Block %2 illegal DE F or PROC instruction in the part program
Ver solución Código 14510
[Channel %1: ] Block %2 PROC instruction missing on subroutine call
Ver solución Código 14520
[Channel %1: ] Block %2 illegal PROC instruction in data definition section
Ver solución Código 14530
[Channel %1: ] Block %2 EXTERN and PROC instruction do not correspond
Ver solución Código 14540
[Channel %1: ] Block %2 contour t ool: the min. limit angle has been programmed more than once (edge D%3)
Ver solución Código 14541
[Channel %1: ] Block %2 contour tool: the max. limit angle has been programmed more than once (edge D%3)
Ver solución Código 14542
[Channel %1: ] Block %2 contour tool : the min. limit angle has not been programmed
Ver solución Código 14543
[Channel %1: ] Block %2 contour tool: the max. limit angle has not been programmed
Ver solución Código 14544
[Channel %1: ] Block %2 contour tool: edge D%3 is not positioned between the two border edges
Ver solución Código 14545
[Channel %1: ] Block %2 contour tool: edge D%3 completely encircles edge D%4
Ver solución Código 14546
[Channel %1: ] Block %2 contour tool: edge D%3 defines a concave corner
Ver solución Código 14547
[Channel %1: ] Block %2 contour tool: checksum erroneous or not available
Ver solución Código 14548
[Channel %1: ] Block %2 contour tool: negative radius in edge D%3 is not allowed
Ver solución Código 14549
[Channel %1: ] Block %2 contour tool: impermissible programming. Code no. %3
Ver solución Código 14550
[Channel %1: ] Block %2 contour tool: impermissible tool contour change. Code no. %3
Ver solución Código 14551
[Channel %1: ] Block %2 contour tool: angle area of edge D%3 larger than 359 degrees
Ver solución Código 14600
[Channel %1: ] Block %2 reload buffer %3 cannot be established
Ver solución Código 14601
[Channel %1: ] Block %2 reload buffer could not be deleted
Ver solución Código 14602
[Channel %1: ] Block %2 timeout while reloading from external.
Ver solución Código 14603
[Channel %1: ] Block %2 timeout during execution from external source.
Ver solución Código 14610
[Channel %1: ] Block %2 compensation block not possible
Ver solución Código 14615
[Channel %1: ] An error occurred while handling the function 'syntax check': identifier %3
Ver solución Código 14650
[Channel %1: ] Block %2 SETINT in struction with invalid ASUP input
Ver solución Código 14660
[Channel %1: ] Block %2 SETINT instruction with invalid priority
Ver solución Código 14700
[Channel %1: ] Block %2 timeout during command to interpreter
Ver solución Código 14701
[Channel %1: ] Block %2 number of available NC blocks reduced by %3
Ver solución Código 14710
[Channel %1: ] Block %2 error in initialization sequence in function %3
Ver solución Código 14711
[Channel %1: ] Transformation selection not possible as axis %2 not available
Ver solución Código 14720
[Channel %1: ] Block %2 axes for centerless transformation not available
Ver solución Código 14730
[Channel %1: ] Block %2 conflict at activation of centerless transformation
Ver solución Código 14740
[Channel %1: ] Block %2 no tool data available for centerless grinding
Ver solución Código 14745
[Channel %1: ] Block %2 centerless grinding not active
Ver solución Código 14750
[Channel %1: ] Block %2 too many auxiliary functions programmed
Ver solución Código 14751
[Channel %1: ] Block %2 resources for motion synchronous actions not sufficient (code: %3)
Ver solución Código 14752
[Channel %1: ] Block %2 DELDTG | STOPREOF conflict
Ver solución Código 14753
[Channel %1: ] Block %2 motion synchronous actions with illegal interpolation type
Ver solución Código 14754
[Channel %1: ] Block %2 motion synchronous actions and wrong feed type
Ver solución Código 14755
[Channel %1: ] Block %2 motion synchronous actions without traverse motion
Ver solución Código 14756
[Channel %1: ] Block %2 motion synchronous action and wrong value
Ver solución Código 14757
[Channel %1: ] Block %2 motion synchronous action and wrong type
Ver solución Código 14758
[Channel %1: ] Block %2 programmed value not available
Ver solución Código 14759
[Channel %1: ] Block %2 motion synchronous action and wrong axis type
Ver solución Código 14760
[Channel %1: ] Block %2 auxiliary function of a group programmed repeatedly
Ver solución Código 14761
[Channel %1: ] Block %2 motion sy nchronous action: DELDTG function not allowed with active tool radius compensation
Ver solución Código 14762
[Channel %1: ] Block %2 too many PLC variables programmed
Ver solución Código 14763
[Channel %1: ] Block %2 too many link variables programmed
Ver solución Código 14764
NCU link cannot transfer all link variables immediately
Ver solución Código 14765
NCU link cannot transfer all link variables
Ver solución Código 14766
NCU link is heavily loaded, impending memory shortage
Ver solución Código 14767
Machine data matching via NCU link not complete
Ver solución Código 14768
Axial auxiliary function for the NCU link cannot be output
Ver solución Código 14769
[Channel %1: ] Block %2 Spindle %3 Implicit auxiliary function %4 Buffer full
Ver solución Código 14770
[Channel %1: ] Block %2 auxiliary function programmed incorrectly
Ver solución Código 14780
[Channel %1: ] Block %2 unreleased option used (identification %3)
Ver solución Código 14782
[Channel %1: ] Block %2 non-active function used (identification %3)
Ver solución Código 14783
[Channel %1: ] Block %2 coordinate system-specific working area limitation is not active
Ver solución Código 14790
[Channel %1: ] Block %2 axis %3 programmed by PLC
Ver solución Código 14800
[Channel %1: ] Block %2 programmed path speed less or equal to zero
Ver solución Código 14810
[Channel %1: ] Block %2 negative axis speed programmed for positioning axis %3
Ver solución Código 14811
[Channel %1: ] Block %2 incorrect value range for acceleration of axis/spindle %3
Ver solución Código 14812
[Channel %1: ] Block %2 SOFTA not available for axis %3
Ver solución Código 14815
[Channel %1: ] Block %2 negative thread pitch change programmed
Ver solución Código 14820
[Channel %1: ] Block %2 negative value for maximum spindle speed programmed with constant cutting speed
Ver solución Código 14821
[Channel %1: ] Block %2 error in selection or deselection of GWPS
Ver solución Código 14822
[Channel %1: ] Block %2 incorrect programming of GWPS
Ver solución Código 14823
[Channel %1: ] Block %2 error on selection or deselection of tool monitoring
Ver solución Código 14824
[Channel %1: ] Block %2 conflict with GWPS
Ver solución Código 14830
[Channel %1: ] Block %2 wrong feed type selected
Ver solución Código 14840
[Channel %1: ] Block %2 incorrect value range for constant cutting speed
Ver solución Código 14850
[Channel %1: ] Block %2 changing the reference axis for a constant cutting speed not allowed
Ver solución Código 14860
[Channel %1 ] Block %2 Selection of the tool cutting rate not allowed. Cause %3
Ver solución Código 14861
[Channel %1 ] Block %2 SVC programmed, but no tool offset active
Ver solución Código 14862
[Channel %1 ] Block %2 SVC has been programmed, but the radius of the active tool correction is zero
Ver solución Código 14863
[Channel %1 ] Block %2 The programmed SVC value is zero or negative
Ver solución Código 14900
[Channel %1: ] Block %2 center point and end point programmed simultaneously
Ver solución Código 14910
[Channel %1: ] Block %2 invalid angle of aperture for programmed circle
Ver solución Código 14920
[Channel %1: ] Block %2 intermediate point of circle incorrect
Ver solución Código 15000
[Channel %1: ] Block %2 channel-sync command using illegal marker
Ver solución Código 15010
[Channel %1: ] Block %2 program coordination instruction with invalid channel number
Ver solución Código 15020
Channel %1 block %2 CHANDATA inst ruction cannot be executed. Channel %3 is not active
Ver solución Código 15021
[Channel %1: ] Block %2 CHANDATA instruction with invalid channel number
Ver solución Código 15025
CHANDATA(%2): channel is not acti ve. Channel data will be ignored.
Ver solución Código 15030
[Channel %1: ] Block %2 different measurement system settings
Ver solución Código 15100
[Channel %1: ] Block %2 REORG abort caused by log file overflow
Ver solución Código 15110
[Channel %1: ] Block %2 REORG not possible
Ver solución Código 15120
If a power failure occurs now, th e last data change d will be lost; index/buffer size = %1
Ver solución Código 15122
Power ON after power failure: %1 data were restored, of which %2 machine data, %3 errors.
Ver solución Código 15150
[Channel %1: ] Block %2 reload from external aborted
Ver solución Código 15160
[Channel %1: ] Block %2 wrong preprocessing configuration
Ver solución Código 15165
[Channel %1: ] Block %2 error when translating or interpreting Asup %3
Ver solución Código 15166
[Channel %1: ] User system asup _N_ASUP_SPF not available
Ver solución Código 15170
[Channel %1: ] Block %2 program %3 could not be compiled
Ver solución Código 15171
[Channel %1: ] Block %2 compiled program %3 older than the relevant subroutine
Ver solución Código 15172
[Channel %1: ] Block %2 subroutine %3. No interface available at time of preprocessing.
Ver solución Código 15173
[Channel %1: ] Block %2 variable %3 was unknown at the time of preprocessing.
Ver solución Código 15175
[Channel %1: ] Block %2 program %3. Interfaces could not be built
Ver solución Código 15176
[Channel %1: ] Block %2 Program%3 may only be executed after Power ON
Ver solución Código 15177
[Channel %1: ] Block %2 Error on preprocessing of program %3, error code: %4
Ver solución Código 15180
[Channel %1: ] Block %2: Error on editing program %3 as INI/DEF file.
Ver solución Código 15185
[Channel %1: ] %2 errors in INI file
Ver solución Código 15186
[Channel %1: ] %2 errors in GUD, macro or INI file
Ver solución Código 15187
[Channel %1: ] Error during execution of PROGEVENT file %3.
Ver solución Código 15188
[Channel %1: ] Error during execution of ASUB file %3.
Ver solución Código 15190
[Channel %1: ] Block %2 not enough free memory for subroutine call
Ver solución Código 15300
[Channel %1: ] Block %2 invalid number-of-passed-blocks during block search
Ver solución Código 15310
[Channel %1: ] Block %2 file requested during block search is not available
Ver solución Código 15320
[Channel %1: ] Block %2 invalid block search command
Ver solución Código 15330
[Channel %1: ] Block %2 invalid block number as search target
Ver solución Código 15340
[Channel %1: ] Block %2 invalid label as search target
Ver solución Código 15350
[Channel %1: ] Block %2 search target not found
Ver solución Código 15360
[Channel %1: ] Illegal target of block search (syntax error)
Ver solución Código 15370
[Channel %1: ] Target of block search not found
Ver solución Código 15380
[Channel %1: ] Block %2 illegal incremental programming in axis %3
Ver solución Código 15390
[Channel %1: ] Block %2 %3 not executed during block search
Ver solución Código 15395
[Channel %1: ] Master-slave not executable during block search
Ver solución Código 15400
[Channel %1: ] Block %2 selected initial INIT block does not exist
Ver solución Código 15410
[Channel %1: ] Block %2 initialization file contains invalid M function
Ver solución Código 15420
[Channel %1: ] Block %2 instruction in current mode not allowed
Ver solución Código 15450
[Channel %1: ] Block %2 compiled program cannot be stored
Ver solución Código 15460
[Channel %1: ] Block %2 syntax error when locking
Ver solución Código 15500
[Channel %1: ] Block %2 illegal angle of shear
Ver solución Código 15700
[Channel %1: ] Block %2 illegal cycle alarm number %3
Ver solución Código 15800
[Channel %1: ] Block %2 wrong starting conditions for CONTPRON/CONTDCON
Ver solución Código 15810
[Channel %1: ] Block %2 wrong array dimension for CONTPRON/CONTDCON
Ver solución Código 15900
[Channel %1: ] Block %2 touch probe not allowed
Ver solución Código 15910
[Channel %1: ] Block %2 touch probe not allowed
Ver solución Código 15950
[Channel %1: ] Block %2 no traverse motion programmed
Ver solución Código 15960
[Channel %1: ] Block %2 no traverse motion programmed
Ver solución Código 16000
[Channel %1: ] Block %2 invalid value for lifting direction
Ver solución Código 16005
[Channel %1: ] Block %2 invalid value for lifting distance
Ver solución Código 16010
[Channel %1: ] Block %2 machining stop after lift fast
Ver solución Código 16015
[Channel %1: ] Block %2 wrong axis identifier %3
Ver solución Código 16016
[Channel %1: ] Block %2 no retraction position programmed for axis %3
Ver solución Código 16017
Channel %1 Axis %2 Identifier %3, LIFTFAST ignores this axis, current axis not capable of retraction
Ver solución Código 16020
[Channel %1: ] Repositioning in block %2 is not possible
Ver solución Código 16025
[Channel %1: ] Block %2 impermissible axis exchange in REPOS command by axis %3.
Ver solución Código 16100
[Channel %1: ] Block %2 spindle %3 not available in the channel
Ver solución Código 16105
[Channel %1: ] Block %2 spindle %3 cannot be assigned
Ver solución Código 16110
[Channel %1: ] Block %2 spindle %3 for dwell time not in control mode
Ver solución Código 16111
[Channel %1: ] Block %2 spindle %3 No speed programmed
Ver solución Código 16112
[Channel %1: ] Block %2 foll owing spindle %3 Impermissible programming
Ver solución Código 16120
[Channel %1: ] Block %2 invalid index for tool fine compensation
Ver solución Código 16130
[Channel %1: ] Block %2 command not allowed with FTOCON
Ver solución Código 16140
[Channel %1: ] Block %2 FTOCON not allowed
Ver solución Código 16150
[Channel %1: ] Block %2 invalid spindle number with PUTFTOCF
Ver solución Código 16200
[Channel %1: ] Block %2 spline and polynominal interpolation not available
Ver solución Código 16300
[Channel %1: ] Block %2 denominator polynominal with zero places within parameter range not allowed
Ver solución Código 16400
[Channel %1: ] Block %2 positioning axis %3 cannot participate in spline
Ver solución Código 16410
[Channel %1: ] Block %2 axis %3 is not a geometry axis
Ver solución Código 16420
[Channel %1: ] Block %2 axis %3 programmed repeatedly
Ver solución Código 16421
[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block
Ver solución Código 16422
[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block
Ver solución Código 16423
[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block
Ver solución Código 16424
[Channel %1: ] Block %2 coordinate %3 programmed repeatedly in the block
Ver solución Código 16430
[Channel %1: ] Block %2 geometry axis %3 cannot traverse as positioning axis in rotated coordinate system
Ver solución Código 16440
[Channel %1: ] Block %2 rotation programmed for non-existent geometry axis
Ver solución Código 16500
[Channel %1: ] Block %2 chamfer or rounding negative
Ver solución Código 16510
[Channel %1: ] Block %2 no facing axis for diameter programming available
Ver solución Código 16520
[Channel %1: ] Axis %2, diameter programming active, function %3 is not executed
Ver solución Código 16600
[Channel %1: ] Block %2 spindle %3 gear stage change not possible
Ver solución Código 16670
[Channel %1: ] Block %2 following axis/spindle %3 maximum number of CP modules (%4) has been exceeded
Ver solución Código 16671
[Channel %1: ] Block %2 following axis/spindle %3 maximum number of CP modules (%4) has been exceeded
Ver solución Código 16672
[Channel %1: ] Block %2 leading ax is/spindle %3 ma ximum number of CP master values (%4) exceeded
Ver solución Código 16673
[Channel %1: ] Block %2 leading ax is/spindle %3 ma ximum number of CP master values (%4) exceeded
Ver solución Código 16675
Channel %1 block %2 following axi s/spindle %3 coupling module already defined in channel %4
Ver solución