Siemens SINUMERIK 840D CNC エラーコード

[Channel %1: ] Block %2: Calculation has been cancelled

[Channel %1: ] Block %2: Infeed D is larger than the tip width of the tool

[Channel %1: ] Block %2: Infeed DX or DZ is larger than tip length of tool

[Channel %1: ] Block %2: Tool radius larger than half the tip width

[Channel %1: ] Block %2: System error contour turning %4

[Channel %1: ] Block %2: Machining range outside delimitation

[Channel %1: ] Block %2: Unable to determine contour direction

[Channel %1: ] Block %2: No material available for machining

[Channel %1: ] Block %2: Cutting edge not compatible with cutting direction

[Channel %1: ] Block %2: Machined part contour is outside the blank contour

[Channel %1: ] Block %2: Infeed D larger than the tip length of the tool

[Channel %1: ] Block %2: Machining cutting depth larger than maximum depth of cut of the tool

[Channel %1: ] Block %2: Machining cutting depth smaller than minimum depth of cut of the tool

[Channel %1: ] Block %2: Incorrect cutting edge position

[Channel %1: ] Block %2: Blank must be closed contour

[Channel %1: ] Block %2: Collision through approach

[Channel %1: ] Block %2: Axis in negative range

[Channel %1: ] Block %2: Retraction plane %4 is within the machining range

[Channel %1: ] Block %2: Ext. CNC system missing

[Channel %1: ] Block %2: Wrong G code selected

[Channel %1: ] Block %2: Wrong axis type

[Channel %1: ] Block %2: Programmed axis not available

[Channel %1: ] Block %2: Progr. position exceeds reference point

[Channel %1: ] Block %2: Value programmed absolute and incremental

[Channel %1: ] Block %2: Wrong axis assignment

[Channel %1: ] Block %2: Wrong spindle direction programmed (active)

[Channel %1: ] Block %2: Final drilling depth or single drilling depth missing

[Channel %1: ] Block %2: Drill position not permissible

[Channel %1: ] Block %2: ISO G code not possible

[Channel %1: ] Block %2: ISO axis name illegal

[Channel %1: ] Block %2: Value(s) in external cycle call wrongly defined

[Channel %1: ] Block %2: GUD value wrongly defined

[Channel %1: ] Block %2: Polar coordinates not possible with cycle

[Channel %1: ] Block %2: G40 not active

[Channel %1: ] Block %2: Axes not on reference point

[Channel %1: ] Block %2: Axis coordinates within protection zone

[Channel %1: ] Block %2: Axis range limits are equal

[Channel %1: ] Block %2: Name of program to be generated is missing

[Channel %1: ] Block %2: Contour %4 does not exist

[Channel %1: ] Block %2: Label %4 not existing in the pocket contour

[Channel %1: ] Block %2: Label %4 not existing in the blank contour

[Channel %1: ] Block %2: Label %4 not existing in the island contour

[Channel %1: ] Block %2: Label %4 not existing in the spigot contour

[Channel %1: ] Block %2: Label %4 not existing in the contour

[Channel %1: ] Block %2: Pocket contour missing

[Channel %1: ] Block %2: Blank contour missing

[Channel %1: ] Block %2: Error in pocket contour %4

[Channel %1: ] Block %2: Error in the blank contour %4

[Channel %1: ] Block %2: Error in island contour %4

[Channel %1: ] Block %2: Error in spigot contour %4

[Channel %1: ] Block %2: Error in contour %4

[Channel %1: ] Block %2: Too many contours specified

[Channel %1: ] Block %2: Cutter radius too small

[Channel %1: ] Block %2: Calculation has been cancelled

[Channel %1: ] Block %2: Combination of centering/predrilling and spigot not allowed

[Channel %1: ] Block %2: Cut. radius for residual mach. must be smaller than cut. radius for ref. tool

[Channel %1: ] block %2: Radius of the reference tool is too small

[Channel %1: ] block %2: S ystem error contour milling %4

[Channel %1: ] Block %2: No contour available

[Channel %1: ] Block %2: Contour not closed

[Channel %1: ] Block %2: Selfcutting contour

[Channel %1: ] Block %2: Too many contour elements

[Channel %1: ] Block %2: Programming of the machining plane not allowed here

[Channel %1: ] Block %2: Progra mming of the inch/metric measuring system not allowed here

[Channel %1: ] Block %2: G0 is not allowed in contour programming

[Channel %1: ] Block %2: Pocket depth programmed incorrectly

[Channel %1: ] Block %2: No starting point specified

[Channel %1: ] Block %2: No center point specified for circle

[Channel %1: ] Block %2: Specified starting point programmed incorrectly

[Channel %1: ] Block %2: Helix radius too small

[Channel %1: ] Block %2: Helix violates contour

[Channel %1: ] Block %2: Approach/retract motion violates contour

[Channel %1: ] Block %2: Ramp path too short

[Channel %1: ] Block %2: Plane infeed too large, residual corners remaining

[Channel %1: ] Block %2: Island contour existing twice

[Channel %1: ] Block %2: Spigot contour existing twice

[Channel %1: ] Block %2: No material available for machining

[Channel %1: ] Block %2: Island is outside the pocket

[Channel %1: ] Block %2: No residual material available

[Channel %1: ] Block %2: Cutter radius for residual material too large

[Channel %1: ] Block %2: Radius of the residual material cutter too small in relation to the reference cutter

[Channel %1: ] Block %2: Insert new tool

[Channel %1: ] Block %2: No drilling cycle active

[Channel %1: ] Block %2: Milling direction incorrect - G3 is generated

[Channel %1: ] Block %2: pocket not completely solidly machined during finishing

[Channel %1: ] Block %2: No finishing allowance programmed

[Channel %1: ] Block %2: Drilling cycle incorrectly defined

[Channel %1: ] Block %2: Number of columns or lines equals zero

[Channel %1: ] Block %2: incorrect value for monitoring status in tool monitoring

[Channel %1: ] Block %2: paramete r %4 incorrectly defined for tool monitoring in cycles

[Channel %1: ] Block %2: error in function Tool monitoring in cycles

[Channel %1: ] Block %2: Set rotary axes %4 [deg]

[Channel %1: ] Block %2: Set rotary axis %4 [deg]

[Channel %1: ] Block %2 : load inclinable head: %4

[Channel %1: ] Block %2 : unload inclinable head: %4

[Channel %1: ] Block %2 : replace inclinable head: %4

[Channel %1: ] Block %2 : angle adapted to angle grid: %4

[Channel %1: ] Block %2: No swiveling in JOG -> WO G%4 active and total basic WO (G500) contain rotations

[Channel %1: ] Block %2: Swiveling in JOG --> G500 active and total basic WO or basic reference contain rotations

[Channel %1: ] Block %2: Start spindle

[Channel %1: ] Block %2: Z offset does not influence the retraction planes.

[Channel %1: ] Block %2: NOTICE: t ool travels directly to machining!

[Channel %1: ] Block %2: Check number of empirical value memory

[Channel %1: ] Block %2: Safety margin exceeded

[Channel %1: ] Block %2: Allowance

[Channel %1: ] Block %2: Dimension too small

[Channel %1: ] Block %2: Permissible measuring difference exceeded

[Channel %1: ] Block %2: Maximum number of characters per line exceeded.

[Channel %1: ] Block %2: Variable column width not possible

[Channel %1: ] Block %2: Insufficient column width

[Channel %1: ] Block %2: The max. number of characters per line is limited to 200 characters per line

[Channel %1: ] Block %2: The maxi mum number of characters per line _PROTFORM[1] is adjusted.

[Channel %1: ] Block %2: probe is not perpendicular to plane!

[Channel %1: ] Block %2: The number of lines per page _PROTFORM[0] is incorrect and is automatically adjusted.

[Channel %1: ] Block %2: Traverse path limitation via software end position, collision detection activated, continue with NC START / cancel with RESET.

[Channel %1: ] Block %2: Overwrite swivel data record TCARR = %4, yes -> NC start, no -> reset

[Channel %1: ] Block %2: Overwrite TR AORIdata, yes -> NC start, no -> reset

[Channel %1: ] Block %2: Tolerance of the linear vector %4 exceeded

[Channel %1: ] Block %2: Tolerance of the rotary axis vector %4 exceeded

[Channel %1: ] Block %2: No internal correction of the calibration data

[Channel %1: ] Block %2: GWPS has been limited

[Channel %1: ] Block %2: Speed has been limited

[Channel %1: ] Block %2: Dresser %4, GWPS has been limited

[Channel %1: ] Block %2: Dresser %4, speed has been limited

[Channel %1: ] Block %2:

[Channel %1: ] CLC: incorrect MD configuration, error code: %2

[Channel %1: ] CLC: block %2 General programming error

[Channel %1: ] CLC: block %2 CLC_LIM value exceeds MD limit

[Channel %1: ] CLC: block %2 CLC(0) with active TOC

[Channel %1: ] CLC: block %2 orientation changed for TRAFOOF

[Channel %1: ] CLC: block %2 in programmable direction, error ID: %3

[Channel %1: ] CLC: error ID: %2, angle %3

[Channel %1: ] CLC: position offset at lower limit %2

[Channel %1: ] CLC: position offset at upper limit %2

[Channel %1: ] CLC: stopped because sensor head has been touched

[Channel %1: ] MCSC: wrong MD configuration, error code %2

[Channel %1: ] MCSC: CC_COPON CC_COPOFF error code %2

[Channel %1: ] MCSC: tolerance window exceeded axis %2

[Channel %1: ] MCSC: MD modification on active coupling axis %2

[Channel %1: ] MCSC: axes to be coupled are not in standstill axis %2

[Channel %1: ] MCSC: wrong machine data for collision protection axis %2

[Channel %1: ] MCSC: collision monitoring axis %2

Axis %1 stopped by external process monitoring system

[Channel %1: ] RCTR: incorrect MD configuration, error in MD: %2

[Channel %1: ] RCTR: number of axes/axis assignment inconsistent

[Channel %1: ] RCTR: inco rrect TRAFO_TYPE_ : use 4100

[Channel %1: ] RCTR: MD cannot be changed while transformation active.

[Channel %1: ] RCTR: tool parameters incorrect interpreter

[Channel %1: ] RCTR: unreachable position interpreter

[Channel %1: ] RCTR: block: %2, tool parameters incorrect on block editing

[Channel %1: ] RCTR: block: %2, unreachable position on block editing

[Channel %1: ] RCTR: tool parameters incorrect on interpolation

[Channel %1: ] RCTR: Transformation violates software limit switch

[Channel %1: ] RCTR: Excessive velocity near pole, error code %2

[Channel %1: ] RCTR: block: %2, unreachable position on interpolation

[Channel %1: ] HSLC: Configuration error ID=%2

[Channel %1: ] HSLC: CC_FASTON_CONT velocity too high

[Channel %1: ] RESU: wrong MD configuration. Error code %2

[Channel %1: ] RESU: block %2 invalid parameter in CC_PREPRE()

[Channel %1: ] RESU: Return traveling not possible, error code %2

[Channel %1: ] RESU: inte rnal error, error code %2

[Channel %1: ] RESU: retraceable contour was shortened

[Channel %1: ] RESU: resynchronisation not possible

[Channel %1: ] RESU: NC memory limit reached, RAM type %2

[Channel %1: ] RESU: POS axis not permitted, axis type %2, block no. %3

[Channel %1: ] RESU: NC start currently not possible

[Channel %1: ] PROT: Incorrect configuration no. %2

[Channel %1: ] PROT: Collision protection stops axis %2

MS DOS test version !

Test version only !

Function %1 not yet finally implemented!

Block stored

Program stored

Cannot save

Error in tk_getHandle

Error in task communication

Incorrect NCK version

Configuration error: %1, %2

Selected program already opened by another application

No operating area configured for this access level

Error in '%1' :%nlog file : %2

Additional value

Record length %1 reached

No dynamic me mory available

Buffer limit for selection reached

Area disabled for input

Buffer is empty

Search string '%1' not found

Error on saving

Error on opening %1

Write access not allowed in this state

No block marked

Read access not allowed in this state

Actual changes not yet effective

Search string '%1' found

Search string '%1' replaced by '%2'

Please wait, storing program (%1)!

Please wait, flashing file %1 !!!

Please wait, selected group is being copied!

Please wait, selected group is being deleted!