Siemens SINUMERIK 840D CNC 錯誤代碼

F_DP: %1 communication, co nnection %2 reports error %3

F_DP: %1 communication, co nnection %2 reports error %3

F_DP: Communication error %1, error %2

F_DP: Current cycle time %1 [ms] > parameterized cycle time

F_DP: %1 communication, conn ection %2 reports SFC%3 error %4

F_DP: %1 communication, connection %2 reports system error %3 (%4)

PROFIBUS DP: SI fault on axis %1, code %2, value %3, time %4.

PROFIBUS DP: SI fault on axis %1, code %2, value %3, time %4.

NCU link connection to all other NCUs of the link network has been aborted

NCU link connection to the NCU %1 of the link network has been aborted

Error on activation of machine data, NCU network-wide machine data were modified by NCU %1

NCU link: NCU %1 of the link network is not on the bus

NCU link: NCU %1 of the link network not running synchronously

NCU link: conflict in configuration data of NCU %1

NCU link: conflict in timer setting of NCU %1

NCU link: conflict in bus parameters of NCU %1

NCU link: the NCU %1 has not received a message

IPO time insufficient for NCU link. Link cycle time: %1

NCU link: synchronization cycle signal failure %1 times

NCU link: too many link axes configured %1

Serious alarm on NCU %1, axes in follow-up mode

Serious alarm on NCU %1 not yet acknowledged, axes still in follow-up mode

Emergency stop act ivated on NCU %1, ax es in follow-up mode

Emergency stop on NCU %1, axes still in follow-up mode

[Channel %1: ] Axis exchange of axis %2 not possible, PLC axis movement not yet completed

[Channel %1: ] Block %2: No tool offset active

[Channel %1: ] Block %2: Thread pitch incorrectly defined

[Channel %1: ] Block %2: Type of machining incorrectly defined

[Channel %1: ] Block %2: No feed programmed in cycle

[Channel %1: ] Block %2: Incorrect configuration of geometry axes

[Channel %1: ] Block %2: 3rd geometry axis not available

[Channel %1: ] Block %2: Tool radius too large

[Channel %1: ] Block %2: Tool radius too small

[Channel %1: ] Block %2: No tool active

[Channel %1: ] Block %2: Active tool number = 0

[Channel %1: ] Block %2: Finishing allowance too large

[Channel %1: ] Block %2: Scaling not permissible

[Channel %1: ] Block %2: Different scaling in planes

[Channel %1: ] Block %2: Basic settings were changed, program cannot be executed

[Channel %1: ] Block %2: Return plane exceeded

[Channel %1: ] Block %2: Contour is not defined

[Channel %1: ] Block %2: System frame for cycles missing

[Channel %1: ] Block %2: function %4 not present in NCK

[Channel %1: ] Block %2: function %4 not executable with NCK

[Channel %1: ] Block %2: Para meter %4 incorrectly defined

[Channel %1: ] Block %2: Machining not possible with active TRANSMIT/TRACYL

[Channel %1: ] Block %2: Parameter %4 value too high

[Channel %1: ] Block %2: Parameter %4 value too low

[Channel %1: ] Block %2: Parameter %4 value must be unequal to zero

[Channel %1: ] Block %2: Parameter %4 check value

[Channel %1: ] Block %2: Check tool carrier position

[Channel %1: ] Block %2: Cycle cannot be executed with NC function %4.

[Channel %1: ] Block %2: Subroutine %4 does not exist

[Channel %1: ] Block %2: Internal cycle error (%4)

[Channel %1: ] Block %2: Reference point defined incorrectly

[Channel %1: ] Block %2: No spindle direction programmed

[Channel %1: ] Block %2: Number of holes is zero

[Channel %1: ] Block %2: Contour violation of slots

[Channel %1: ] Block %2: Milling cutter radius too large

[Channel %1: ] Block %2: Number of or distance between circular elements

[Channel %1: ] Block %2: First drilling depth incorrectly defined

[Channel %1: ] Block %2: Illegal values for radius and insertion depth parameters

[Channel %1: ] Block %2: Milling direction parameter incorrectly defined

[Channel %1: ] Block %2: Finishing allowance at bottom > depth infeed

[Channel %1: ] Block %2: Infeed width > Tool diameter

[Channel %1: ] Block %2: Tool radius negative

[Channel %1: ] Block %2: Parameter for corn er radius too large

[Channel %1: ] Block %2: Machining direction G41/G42 incorrectly defined

[Channel %1: ] Block %2: Approach or retract mode(straight / circle / plane / space) incorrectly defined

[Channel %1: ] Block %2: Approach or retract path = 0

[Channel %1: ] Block %2: Active tool radius <= 0

[Channel %1: ] Block %2: Length or width = 0

[Channel %1: ] Block %2: Nominal or core diameter programmed incorrectly

[Channel %1: ] Block %2: Thread type inside / outside not defined

[Channel %1: ] Block %2: Number of teeth per cutting edge is missing

[Channel %1: ] Block %2: Safety distance incorrectly defined in plane

[Channel %1: ] Block %2: CYCLE72 cannot be simulated

[Channel %1: ] Block %2: Infeed width is not programmed

[Channel %1: ] Block %2: Technology selection parameter incorrectly defined

[Channel %1: ] Block %2: Thread length too short

[Channel %1: ] Block %2: Wrong definition of tapping axis transformation ratio (machine data)

[Channel %1: ] Block %2: Insertion angle = 0 for insertion with oscillation or helix

[Channel %1: ] Block %2: perpendic. approach and retraction during contour milling only allowed with G40

[Channel %1: ] Block %2: positions of parallel axes cannot be compensated. No workpiece reference agreed.

[Channel %1: ] Block %2: parameter _GEO incorrect, _GEO=%4

[Channel %1: ] Block %2: Parallel axis parameters incorrect, check values for parallel ax is parameters ABS/INK

[Channel %1: ] Block %2: 3rd parallel axis parameter incorrect, check axis name or GUD _SCW_N[]

[Channel %1: ] Block %2: Rotary axis parameters incorrect, check values for rotary axis parameters ABS/INK

[Channel %1: ] Block %2: incorrect parameter sequence for approaching target position: %4

[Channel %1: ] Block %2: no 3rd geometry axis agreed in GUD _SCW_N[]

[Channel %1: ] Block %2: swiveling and parallel axes cycle are mutually exclusive because of workpiece reference $P_WPFRAME

[Channel %1: ] Block %2: paramete r %4 incorrectly defined for tool monitoring in cycles

[Channel %1: ] Block %2: error in function Tool monitoring in cycles

[Channel %1: ] Block %2: Tool cannot be aligned --> error code: %4

[Channel %1: ] Block %2: Orientation of tool not possible --> error code: %4

[Channel %1: ] Block %2: B axis kinematics (turning technology) either not or incorrectly set up in Start-up of swivel cycle --> error code: %4

[Channel %1: ] Block %2: No 'Rotary axes direct' swivel mode possible - -> error code: %4

[Channel %1: ] Block %2: Final depth wrongly programmed

[Channel %1: ] Block %2: Unit for plane infeed wrongly programmed

[Channel %1: ] Block %2: Depth calculation wrongly programmed

[Channel %1: ] Block %2: Reference point wrongly programmed

[Channel %1: ] Block %2: Machining plane wrongly programmed

[Channel %1: ] Block %2: Machining plane on cycle call differs from the one in the position pattern

[Channel %1: ] Block %2: Residual material remains stationary, reduce plane infeed

[Channel %1: ] Block %2: Centering diameter or tool parameter (diameter, tip an gle) are incorrect

[Channel %1: ] Block %2: Tool parameter diameter or tip angle incorrect

[Channel %1: ] Block %2: angle of aperture programmed too small

[Channel %1: ] Block %2: text length programmed too small

[Channel %1: ] Block %2: polar text length > 360 degrees

[Channel %1: ] Block %2: code page not present

[Channel %1: ] Block %2: character does not exist, no.: %4

[Channel %1: ] Block %2: No name assigned to swivel data record

[Channel %1: ] Block %2 : NCK software version is insufficient for the Swivel function

[Channel %1: ] Block %2: Name of swivel data record unknown: %4

[Channel %1: ] Block %2: Swivel CYCLE800: Retraction mode parameter lies outside value range: %4

[Channel %1: ] Block %2: No soluti on possible with current input angle values

[Channel %1: ] Block %2: Invalid angular ranges of rotary axes in swivel data record: %4

[Channel %1: ] Block %2: Invalid rotary axis vectors --> Check commissioning of swivel CYCLE800

[Channel %1: ] Block %2: Check start-up swivel cycle CYCLE800 --> Error code: %4

[Channel %1: ] Block %2: No axis name agreed for rotary axis 1 -> Check commissioning of swivel CYCLE800

[Channel %1: ] Block %2: Swivel di rect: Invalid rotary axis positions: %4

[Channel %1: ] Block %2: Unable to retract prior to swiveling -> Error code: %4

[Channel %1: ] Block %2: Multi-axis transformation not set up. Error code: %4

[Channel %1: ] Block %2: Additional multi-axis transformations not set up. Error code: %4

[Channel %1: ] Block %2: compressor option not set up

[Channel %1: ] Block %2: spline interpolation option not set up

[Channel %1: ] Block %2: No swiveling in JOG --> Multi-axis transformations and TCARR ac tivated at the same time

[Channel %1: ] Block %2: Swiveling - plane not allowed -> Error code %4

[Channel %1: ] Block %2: Swiveling with kinematic chain -> Error code: %4

[Channel %1: ] Block %2: Swiveling - tool not allowed -> Error code: %4

[Channel %1: ] Block %2: Too many elements in machining block

[Channel %1: ] Block %2: Wrong sequence in machining block

[Channel %1: ] Block %2: No technology cycle

[Channel %1: ] Block %2: No position cycle

[Channel %1: ] Block %2: Technology cycle unknown

[Channel %1: ] Block %2: Position cycle unknown

[Channel %1: ] Block %2: Block search element not found

[Channel %1: ] Block %2: Absolute reference missing

[Channel %1: ] Block %2: Wrong tool type

[Channel %1: ] Block %2: Circle radius too small

[Channel %1: ] Block %2: No pitch programmed

[Channel %1: ] Block %2: Unfinished dimension incorrectly programmed

[Channel %1: ] Block %2: Feed/toot h only possible with cutting tools

[Channel %1: ] Block %2: Cutting speed programmed for tool radius 0

[Channel %1: ] Block %2: Feed/tooth programmed, but number of tools equals zero

[Channel %1: ] Block %2: Tool radius too large

[Channel %1: ] Block %2: Tool radius too small

[Channel %1: ] Block %2: No tool active

[Channel %1: ] Block %2: Plane infeed greater than tool diameter

[Channel %1: ] Block %2: Approach path too small

[Channel %1: ] Block %2: Retract path too small

[Channel %1: ] Block %2: Swivel data record unknown

[Channel %1: ] Block %2: Inclinable head cannot be exchanged

[Channel %1: ] Block %2: Tool probe diameter too small

[Channel %1: ] Block %2: ShopMill program %4 not executable, as not tested by ShopMill

[Channel %1: ] Block %2: Impossible to load magazine tool

[Channel %1: ] Block %2: Thread angle wrongly defined

[Channel %1: ] Block %2: ShopMill subroutine %4 cannot be executed, as not tested by ShopMill

[Channel %1: ] Block %2: ShopTurn program %4 cannot be executed as not tested by ShopTurn.

[Channel %1: ] Block %2: ShopTurn subroutine %4 cannot be executed as not tested by ShopTurn.

[Channel %1: ] Block %2: Retraction direction unknown. Withdraw tool manually!

[Channel %1: ] Block %2: Machining direction unknown!

[Channel %1: ] Block %2: Tool change point lies within retraction area!

[Channel %1: ] Block %2: Wrong feed type

[Channel %1: ] Block %2: Retraction plane not defined for this machining direction

[Channel %1: ] Block %2: Wrong machine direction

[Channel %1: ] Block %2: Correct tool change point, tool tip in

[Channel %1: ] Block %2: Pitch change causing

[Channel %1: ] Block %2: Machining plane does not match modal

[Channel %1: ] Block %2: Safety distance too small

[Channel %1: ] Block %2: Blank radius too small

[Channel %1: ] Block %2: Infeed too small

[Channel %1: ] Block %2: Number of edges too small

[Channel %1: ] Block %2: Width across flats/edge length too small

[Channel %1: ] Block %2: Width across flats/edge length too large

[Channel %1: ] Block %2: Chamfer/radius too large

[Channel %1: ] Block %2: No finishing allowance programmed

[Channel %1: ] Block %2: Error while traveling to fixed stop

[Channel %1: ] Block %2: Error during cut-off: Tool broken?

[Channel %1: ] Block %2: Mirroring not allowed at program start. Deselect work offset!

[Channel %1: ] Block %2: incomplete installation of counterspindle

[Channel %1: ] Block %2: set parameters for counterspindle chuck in the spindle image

[Channel %1: ] Block %2: program contains new machining steps from ShopMill %4

[Channel %1: ] Block %2: program contains new machining steps from ShopTurn %4

[Channel %1: ] Block %2: center offset too large

[Channel %1: ] Block %2: pitch not possible with selected tool

[Channel %1: ] Block %2: Chained ShopMill program blocks not permissible in subprogram on pos. pattern

[Channel %1: ] Block %2: Chained ShopTurn program blocks not permissible in subprogram on pos. pattern

[Channel %1: ] Block %2: Too many restrictions, use rectangular pocket

[Channel %1: ] Block %2: Illegal machining direction

[Channel %1: ] Block %2: Plane infeed too large, residual corners remain

[Channel %1: ] Block %2: Illegal machining direction, residual corners are left over.

[Channel %1: ] Block %2: External tool diameter too small

[Channel %1: ] Block %2: Chamfer width too small

[Channel %1: ] Block %2: Chamfer width > tool radius

[Channel %1: ] Block %2: Insertion depth too small

[Channel %1: ] Block %2: Insertion depth too large

[Channel %1: ] Block %2: Invalid tool angle

[Channel %1: ] Block %2: Target poi nt violates software limit switch!

[Channel %1: ] Block %2: External to ol diameter required for restrictions