Siemens SINUMERIK 840D CNC 錯誤代碼

[Channel %1: ] Block %2 different values under H and D addresses

[Channel %1: ] Block %2 H and D addresses must be programmed after Siemens offset

[Channel %1: ] Block %2 G44 is not possible with tool offset H99

[Channel %1: ] Block %2 D number %3 is not defined

[Channel %1: ] Block %2 ISO2 mode, and toolcarrier or tool adapter are both active (identifier %3)

[Channel %1: ] Block %2 H number with G49

[Channel %1: ] Block %2 D number with G49

[Channel %1: ] Block %2 error %3 on interpreting the contents of $SC_CUTDIRMOD

[Channel %1: ] Block %2 D number and H number programmed simultaneously

[Channel %1: ] Block %2 illegal change of tool direction with tool offset

[Channel %1: ] Block %2 illegal plane change for tool with diameter component

[Channel %1: ] Block %2 negative polar radius

[Channel %1: ] Block %2 polar angle too large

[Channel %1: ] Block %2 negative pole radius

[Channel %1: ] Block %2 pole angle too large

[Channel %1: ] Block %2 pole programmed incorrectly

[Channel %1: ] Block %2 polar coordinates programmed incorrectly

[Channel %1: ] Block %2 polynominal degree greater than 5 programmed for polynominal interpolation

[Channel %1: ] Block %2 overlaid handwheel motion activated incorrectly

[Channel %3: ] Axis %4: handwheel %1 used twice (%2)

[Channel %1: ] Block %2 tool radius compensation active at transformation switchover

[Channel %1: ] Block %2 transformation not available

[Channel %1: ] Block %2 spline active at transformation change

[Channel %1: ] Block %2 preprocessing and main run might not be synchronized

[Channel %1: ] Block %2 illegal parameterization of transformation

[Channel %1: ] Block %2 spline active at geometry axis changeover

[Channel %1: ] Block %2 tool radius compensation active at geometry axis changeover

[Channel %1: ] Block %2 transformation active at geometry axis changeover

[Channel %1: ] Block %2 fine tool correction: changeover geometry/channel axis not allowed

[Channel %1: ] Block %2 GEOAX function: incorrect call

[Channel %1: ] Block %2 tangent control: changeover geometry/channel axis not allowed

[Channel %1: ] Block %2 index axis %3 frame not allowed

[Channel %1: ] Block %2 tangential axis %3 must not be traversed as POS axis

[Channel %1: ] Block %2 rounding length for tangential axis %3 is zero.

[Channel %1: ] Block %2 rel. lift-off path for tangential axis %3 is invalid

[Channel %1: ] Block %2 illegal DE F or PROC instruction in the part program

[Channel %1: ] Block %2 PROC instruction missing on subroutine call

[Channel %1: ] Block %2 illegal PROC instruction in data definition section

[Channel %1: ] Block %2 EXTERN and PROC instruction do not correspond

[Channel %1: ] Block %2 contour t ool: the min. limit angle has been programmed more than once (edge D%3)

[Channel %1: ] Block %2 contour tool: the max. limit angle has been programmed more than once (edge D%3)

[Channel %1: ] Block %2 contour tool : the min. limit angle has not been programmed

[Channel %1: ] Block %2 contour tool: the max. limit angle has not been programmed

[Channel %1: ] Block %2 contour tool: edge D%3 is not positioned between the two border edges

[Channel %1: ] Block %2 contour tool: edge D%3 completely encircles edge D%4

[Channel %1: ] Block %2 contour tool: edge D%3 defines a concave corner

[Channel %1: ] Block %2 contour tool: checksum erroneous or not available

[Channel %1: ] Block %2 contour tool: negative radius in edge D%3 is not allowed

[Channel %1: ] Block %2 contour tool: impermissible programming. Code no. %3

[Channel %1: ] Block %2 contour tool: impermissible tool contour change. Code no. %3

[Channel %1: ] Block %2 contour tool: angle area of edge D%3 larger than 359 degrees

[Channel %1: ] Block %2 reload buffer %3 cannot be established

[Channel %1: ] Block %2 reload buffer could not be deleted

[Channel %1: ] Block %2 timeout while reloading from external.

[Channel %1: ] Block %2 timeout during execution from external source.

[Channel %1: ] Block %2 compensation block not possible

[Channel %1: ] An error occurred while handling the function 'syntax check': identifier %3

[Channel %1: ] Block %2 SETINT in struction with invalid ASUP input

[Channel %1: ] Block %2 SETINT instruction with invalid priority

[Channel %1: ] Block %2 timeout during command to interpreter

[Channel %1: ] Block %2 number of available NC blocks reduced by %3

[Channel %1: ] Block %2 error in initialization sequence in function %3

[Channel %1: ] Transformation selection not possible as axis %2 not available

[Channel %1: ] Block %2 axes for centerless transformation not available

[Channel %1: ] Block %2 conflict at activation of centerless transformation

[Channel %1: ] Block %2 no tool data available for centerless grinding

[Channel %1: ] Block %2 centerless grinding not active

[Channel %1: ] Block %2 too many auxiliary functions programmed

[Channel %1: ] Block %2 resources for motion synchronous actions not sufficient (code: %3)

[Channel %1: ] Block %2 DELDTG | STOPREOF conflict

[Channel %1: ] Block %2 motion synchronous actions with illegal interpolation type

[Channel %1: ] Block %2 motion synchronous actions and wrong feed type

[Channel %1: ] Block %2 motion synchronous actions without traverse motion

[Channel %1: ] Block %2 motion synchronous action and wrong value

[Channel %1: ] Block %2 motion synchronous action and wrong type

[Channel %1: ] Block %2 programmed value not available

[Channel %1: ] Block %2 motion synchronous action and wrong axis type

[Channel %1: ] Block %2 auxiliary function of a group programmed repeatedly

[Channel %1: ] Block %2 motion sy nchronous action: DELDTG function not allowed with active tool radius compensation

[Channel %1: ] Block %2 too many PLC variables programmed

[Channel %1: ] Block %2 too many link variables programmed

NCU link cannot transfer all link variables immediately

NCU link cannot transfer all link variables

NCU link is heavily loaded, impending memory shortage

Machine data matching via NCU link not complete

Axial auxiliary function for the NCU link cannot be output

[Channel %1: ] Block %2 Spindle %3 Implicit auxiliary function %4 Buffer full

[Channel %1: ] Block %2 auxiliary function programmed incorrectly

[Channel %1: ] Block %2 unreleased option used (identification %3)

[Channel %1: ] Block %2 non-active function used (identification %3)

[Channel %1: ] Block %2 coordinate system-specific working area limitation is not active

[Channel %1: ] Block %2 axis %3 programmed by PLC

[Channel %1: ] Block %2 programmed path speed less or equal to zero

[Channel %1: ] Block %2 negative axis speed programmed for positioning axis %3

[Channel %1: ] Block %2 incorrect value range for acceleration of axis/spindle %3

[Channel %1: ] Block %2 SOFTA not available for axis %3

[Channel %1: ] Block %2 negative thread pitch change programmed

[Channel %1: ] Block %2 negative value for maximum spindle speed programmed with constant cutting speed

[Channel %1: ] Block %2 error in selection or deselection of GWPS

[Channel %1: ] Block %2 incorrect programming of GWPS

[Channel %1: ] Block %2 error on selection or deselection of tool monitoring

[Channel %1: ] Block %2 conflict with GWPS

[Channel %1: ] Block %2 wrong feed type selected

[Channel %1: ] Block %2 incorrect value range for constant cutting speed

[Channel %1: ] Block %2 changing the reference axis for a constant cutting speed not allowed

[Channel %1 ] Block %2 Selection of the tool cutting rate not allowed. Cause %3

[Channel %1 ] Block %2 SVC programmed, but no tool offset active

[Channel %1 ] Block %2 SVC has been programmed, but the radius of the active tool correction is zero

[Channel %1 ] Block %2 The programmed SVC value is zero or negative

[Channel %1: ] Block %2 center point and end point programmed simultaneously

[Channel %1: ] Block %2 invalid angle of aperture for programmed circle

[Channel %1: ] Block %2 intermediate point of circle incorrect

[Channel %1: ] Block %2 channel-sync command using illegal marker

[Channel %1: ] Block %2 program coordination instruction with invalid channel number

Channel %1 block %2 CHANDATA inst ruction cannot be executed. Channel %3 is not active

[Channel %1: ] Block %2 CHANDATA instruction with invalid channel number

CHANDATA(%2): channel is not acti ve. Channel data will be ignored.

[Channel %1: ] Block %2 different measurement system settings

[Channel %1: ] Block %2 REORG abort caused by log file overflow

[Channel %1: ] Block %2 REORG not possible

If a power failure occurs now, th e last data change d will be lost; index/buffer size = %1

Power ON after power failure: %1 data were restored, of which %2 machine data, %3 errors.

[Channel %1: ] Block %2 reload from external aborted

[Channel %1: ] Block %2 wrong preprocessing configuration

[Channel %1: ] Block %2 error when translating or interpreting Asup %3

[Channel %1: ] User system asup _N_ASUP_SPF not available

[Channel %1: ] Block %2 program %3 could not be compiled

[Channel %1: ] Block %2 compiled program %3 older than the relevant subroutine

[Channel %1: ] Block %2 subroutine %3. No interface available at time of preprocessing.

[Channel %1: ] Block %2 variable %3 was unknown at the time of preprocessing.

[Channel %1: ] Block %2 program %3. Interfaces could not be built

[Channel %1: ] Block %2 Program%3 may only be executed after Power ON

[Channel %1: ] Block %2 Error on preprocessing of program %3, error code: %4

[Channel %1: ] Block %2: Error on editing program %3 as INI/DEF file.

[Channel %1: ] %2 errors in INI file

[Channel %1: ] %2 errors in GUD, macro or INI file

[Channel %1: ] Error during execution of PROGEVENT file %3.

[Channel %1: ] Error during execution of ASUB file %3.

[Channel %1: ] Block %2 not enough free memory for subroutine call

[Channel %1: ] Block %2 invalid number-of-passed-blocks during block search

[Channel %1: ] Block %2 file requested during block search is not available

[Channel %1: ] Block %2 invalid block search command

[Channel %1: ] Block %2 invalid block number as search target

[Channel %1: ] Block %2 invalid label as search target

[Channel %1: ] Block %2 search target not found

[Channel %1: ] Illegal target of block search (syntax error)

[Channel %1: ] Target of block search not found

[Channel %1: ] Block %2 illegal incremental programming in axis %3

[Channel %1: ] Block %2 %3 not executed during block search

[Channel %1: ] Master-slave not executable during block search

[Channel %1: ] Block %2 selected initial INIT block does not exist

[Channel %1: ] Block %2 initialization file contains invalid M function

[Channel %1: ] Block %2 instruction in current mode not allowed

[Channel %1: ] Block %2 compiled program cannot be stored

[Channel %1: ] Block %2 syntax error when locking

[Channel %1: ] Block %2 illegal angle of shear

[Channel %1: ] Block %2 illegal cycle alarm number %3

[Channel %1: ] Block %2 wrong starting conditions for CONTPRON/CONTDCON

[Channel %1: ] Block %2 wrong array dimension for CONTPRON/CONTDCON

[Channel %1: ] Block %2 touch probe not allowed

[Channel %1: ] Block %2 touch probe not allowed

[Channel %1: ] Block %2 no traverse motion programmed

[Channel %1: ] Block %2 no traverse motion programmed

[Channel %1: ] Block %2 invalid value for lifting direction

[Channel %1: ] Block %2 invalid value for lifting distance

[Channel %1: ] Block %2 machining stop after lift fast

[Channel %1: ] Block %2 wrong axis identifier %3

[Channel %1: ] Block %2 no retraction position programmed for axis %3

Channel %1 Axis %2 Identifier %3, LIFTFAST ignores this axis, current axis not capable of retraction

[Channel %1: ] Repositioning in block %2 is not possible

[Channel %1: ] Block %2 impermissible axis exchange in REPOS command by axis %3.

[Channel %1: ] Block %2 spindle %3 not available in the channel

[Channel %1: ] Block %2 spindle %3 cannot be assigned

[Channel %1: ] Block %2 spindle %3 for dwell time not in control mode

[Channel %1: ] Block %2 spindle %3 No speed programmed

[Channel %1: ] Block %2 foll owing spindle %3 Impermissible programming

[Channel %1: ] Block %2 invalid index for tool fine compensation

[Channel %1: ] Block %2 command not allowed with FTOCON

[Channel %1: ] Block %2 FTOCON not allowed

[Channel %1: ] Block %2 invalid spindle number with PUTFTOCF

[Channel %1: ] Block %2 spline and polynominal interpolation not available

[Channel %1: ] Block %2 denominator polynominal with zero places within parameter range not allowed

[Channel %1: ] Block %2 positioning axis %3 cannot participate in spline

[Channel %1: ] Block %2 axis %3 is not a geometry axis

[Channel %1: ] Block %2 axis %3 programmed repeatedly

[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block

[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block

[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block

[Channel %1: ] Block %2 coordinate %3 programmed repeatedly in the block

[Channel %1: ] Block %2 geometry axis %3 cannot traverse as positioning axis in rotated coordinate system

[Channel %1: ] Block %2 rotation programmed for non-existent geometry axis

[Channel %1: ] Block %2 chamfer or rounding negative

[Channel %1: ] Block %2 no facing axis for diameter programming available

[Channel %1: ] Axis %2, diameter programming active, function %3 is not executed

[Channel %1: ] Block %2 spindle %3 gear stage change not possible

[Channel %1: ] Block %2 following axis/spindle %3 maximum number of CP modules (%4) has been exceeded

[Channel %1: ] Block %2 following axis/spindle %3 maximum number of CP modules (%4) has been exceeded

[Channel %1: ] Block %2 leading ax is/spindle %3 ma ximum number of CP master values (%4) exceeded

[Channel %1: ] Block %2 leading ax is/spindle %3 ma ximum number of CP master values (%4) exceeded

Channel %1 block %2 following axi s/spindle %3 coupling module already defined in channel %4