Fanuc の全機種へ戻る Search all database
Fanuc R-30i Series Robot Controller
Fanuc R-30i Series Robot Controller エラーコード
Fanuc R-30i Series Robot Controller の完全なアラーム・エラーコードリファレンス。以下に全 6553 件の故障コードを掲載し、各コードから詳細なトラブルシューティングガイドへ移動できます。
Search this section
Search Fanuc R-30i Series Robot Controller
Search all 6553 Fanuc R-30i Series Robot Controller codes without changing pages.
完全アラーム一覧 (Page 24 of 33)
コード SEAL-049
Calibrations not complete (E%d)
解決方法を見る コード SEAL-050
Shot meter not full (E%d)
解決方法を見る コード SEAL-051
Both Drums are empty (E%d)
解決方法を見る コード SEAL-052
Same fault posted repeatedly (E%d)
解決方法を見る コード SEAL-053
Robot is in dry run mode
解決方法を見る コード SEAL-054
Robot lock mode is ON
解決方法を見る コード SEAL-055
Part ID out of range
解決方法を見る コード SEAL-056
Dispenser not ready (E%s)
解決方法を見る コード SEAL-057
Dispenser fault (E%s)
解決方法を見る コード SEAL-058
Flow rate fault (E%s)
解決方法を見る コード SEAL-059
Not calibrated warning (E%s)
解決方法を見る コード SEAL-060
High pressure (E%d)
解決方法を見る コード SEAL-061
Seal not ready
解決方法を見る コード SEAL-062
Reload fault (E%d)
解決方法を見る コード SEAL-063
High pressure
解決方法を見る コード SEAL-064
Not at purge position
解決方法を見る コード SEAL-065
Maximum purge count reached
解決方法を見る コード SEAL-066
Seal not start
解決方法を見る コード SEAL-067
Seal interrupt
解決方法を見る コード SEAL-068
Flow command excessive%s
解決方法を見る コード SEAL-069
Dispenser malfunction (E%d)
解決方法を見る コード SEAL-070
Gun malfunction (E%d)
解決方法を見る コード SEAL-071
Gun full open too long (E%d)
解決方法を見る コード SEAL-072
High nozzle pressure (E%d)
解決方法を見る コード SEAL-073
High dispensed volume (E%d)
解決方法を見る コード SEAL-074
Low dispensed volume (E%d)
解決方法を見る コード SEAL-075
Flow meter fault (E%d)
解決方法を見る コード SEAL-076
Bead defect detected (E%d)
解決方法を見る コード SEAL-077
Sealer equipment fault (E%d)
解決方法を見る コード SEAL-078
Dispenser comm fault (E%d)
解決方法を見る コード SEAL-079
Dispenser E-stop (E%d)
解決方法を見る コード SEAL-080
Dispenser fault (E%d)
解決方法を見る コード SEAL-081
Volume comp at maximum (E%d)
解決方法を見る コード SEAL-082
Drum A empty (E%d)
解決方法を見る コード SEAL-083
Drum B empty (E%d)
解決方法を見る コード SEAL-084
Reload timed out (E%d)
解決方法を見る コード SEAL-085
Calibration aborted
解決方法を見る コード SEAL-086
Volume strobe timeout (E%d)
解決方法を見る コード SEAL-087
Volume above limit (E%d)
解決方法を見る コード SEAL-088
Material cal timeout (E%d)
解決方法を見る コード SEAL-089
Volume below limit (E%d)
解決方法を見る コード SEAL-090
Nozzle over pressure (E%d)
解決方法を見る コード SEAL-091
Matl weight input = 0 (E%d)
解決方法を見る コード SEAL-092
Specific gravity = 0 (E%d)
解決方法を見る コード SEAL-093
Volume read is zero (E%d)
解決方法を見る コード SEAL-094
Dispense time is zero (E%d)
解決方法を見る コード SEAL-095
Nozzle worn out (E%d)
解決方法を見る コード SEAL-096
Matl press entered=0 (E%d)
解決方法を見る コード SEAL-097
Pressure read is zero (E%d)
解決方法を見る コード SEAL-098
Upstream over pressure (E%d)
解決方法を見る コード SEAL-099
Air pressure entered=0 (E%d)
解決方法を見る コード SEAL-100
NO scale factor/bias (E%d)
解決方法を見る コード SEAL-101
Volume strobe timeout (E%d)
解決方法を見る コード SEAL-102
Press calib incomplete (E%d)
解決方法を見る コード SEAL-103
Dispenser not in AUTO (E%d)
解決方法を見る コード SEAL-104
Analog cal incomplete (E%d)
解決方法を見る コード SEAL-105
Dispenser not ON (E%d)
解決方法を見る コード SEAL-106
Upstream under press (E%d)
解決方法を見る コード SEAL-107
Matl calib incomplete (E%d)
解決方法を見る コード SEAL-108
Material timeout = 0 (E%d)
解決方法を見る コード SEAL-109
Low press>=high press (E%d)
解決方法を見る コード SEAL-110
System/drive not ready (E%d)
解決方法を見る コード SEAL-111
Negative volume read (E%d)
解決方法を見る コード SEAL-112
Vol sig cal incomplete (E%d)
解決方法を見る コード SEAL-113
I/O config incomplete (E%d)
解決方法を見る コード SEAL-114
Dispenser not ready (E%d)
解決方法を見る コード SEAL-115
Too low material flow (E%d)
解決方法を見る コード SEAL-116
Flow command too low
解決方法を見る コード SEAL-117
System/drive not ready (E%d)
解決方法を見る コード SEAL-118
Dispenser not in AUTO (E%d)
解決方法を見る コード SEAL-119
Low pressure (E%d)
解決方法を見る コード SEAL-120
Dispenser not ON (E%d)
解決方法を見る コード SEAL-121
Dispense signal fault (E%d)
解決方法を見る コード SEAL-122
Sealing task already active
解決方法を見る コード SEAL-123
Job aborted
解決方法を見る コード SEAL-124
Critical IO is invalid
解決方法を見る コード SEAL-129
Index incorrect
解決方法を見る コード SEAL-131
SS/SE timing invalid
解決方法を見る コード SEAL-132
Seam segment too short
解決方法を見る コード SEAL-144
Joint motion
解決方法を見る コード SEAL-147
Equipment does not exist
解決方法を見る コード SEAL-148
No SE Instruction
解決方法を見る コード SEAL-149
No equipment number set
解決方法を見る コード SEAL-150
Equipment is already busy
解決方法を見る コード SEAL-151
TPP not created correctly
解決方法を見る コード SEAL-152
I/O not correctly assigned
解決方法を見る コード SEAL-153
Program is running
解決方法を見る コード SEAL-155
No SS Instruction before SE
解決方法を見る コード SEAL-156
MOV_ TPP execution failure
解決方法を見る コード SEAL-157
Seal schedule data is zero
解決方法を見る コード SEAL-159
UTOOL #1 is not taught
解決方法を見る コード SEAL-160
REFPOS is not taught
解決方法を見る コード SEAL-161
OFFSET out of range
解決方法を見る コード SEAL-162
OFFSET config mismatch
解決方法を見る コード SEAL-163
File is not closed
解決方法を見る コード SEAL-164
File does not exist
解決方法を見る コード SEAL-170
Invalid tool position
解決方法を見る コード SEAL-171
Gripper not opened (GP%s)
解決方法を見る コード SEAL-172
Gripper not closed (GP%s)
解決方法を見る コード SEAL-173
Part not present (GP%s)
解決方法を見る コード SEAL-174
Part Present (GP%s)
解決方法を見る コード SEAL-175
Un-assigned Bit mask
解決方法を見る コード SEAL-177
EOAT timed out: Flip
解決方法を見る コード SEAL-178
EOAT timed out: Unflip
解決方法を見る コード SEAL-179
EOAT timed out: Extend
解決方法を見る コード SEAL-180
EOAT timed out: Retract
解決方法を見る コード SEAL-182
Invalid kinimatic solution
解決方法を見る コード SEAL-183
Tool offset internal error
解決方法を見る コード SEAL-200
Dispenser malfunction (E%s)
解決方法を見る コード SEAL-201
Gun malfunction (E%s)
解決方法を見る コード SEAL-202
Gun full open too long (E%s)
解決方法を見る コード SEAL-203
High nozzle pressure (E%s)
解決方法を見る コード SEAL-204
High dispensed volume (E%s)
解決方法を見る コード SEAL-205
Low dispensed volume (E%s)
解決方法を見る コード SEAL-206
Flow meter fault (E%s)
解決方法を見る コード SEAL-207
Bead defect detected (E%s)
解決方法を見る コード SEAL-208
Volume comp at max (E%s)
解決方法を見る コード SEAL-209
Nozzle over pressure (E%s)
解決方法を見る コード SEAL-210
Nozzle under press (E%s)
解決方法を見る コード SEAL-211
Upstream over press (E%s)
解決方法を見る コード SEAL-212
Upstream under press (E%s)
解決方法を見る コード SEAL-213
Sealer equipment fault (E%s)
解決方法を見る コード SEAL-214
No material flow (E%s)
解決方法を見る コード SEAL-215
Reload timed out (E%s)
解決方法を見る コード SEAL-216
Reload fault occured (E%s)
解決方法を見る コード SEAL-217
NO scale factor/bias (E%s)
解決方法を見る コード SEAL-218
Same fault posted (E%s)
解決方法を見る コード SEAL-219
Volume strobe timeout (E%s)
解決方法を見る コード SEAL-220
Volume out of range (E%s)
解決方法を見る コード SEAL-221
Bubble detected (E%d)
解決方法を見る コード SEAL-222
Dispenser not ON (E%s)
解決方法を見る コード SEAL-223
Dispenser not in AUTO (E%s)
解決方法を見る コード SEAL-224
System/drive not ready (E%s)
解決方法を見る コード SEAL-225
Low pressure warning (E%s)
解決方法を見る コード SEAL-226
High pressure warning (E%s)
解決方法を見る コード SEAL-227
Low pressure fault (E%s)
解決方法を見る コード SEAL-228
High pressure fault (E%s)
解決方法を見る コード SEAL-229
Calibration incomplete (E%s)
解決方法を見る コード SEAL-230
High Dispensed Volume (E%d)
解決方法を見る コード SEAL-231
Low Dispensed Volume (E%d)
解決方法を見る コード SEAL-232
High Material Supply Pressure (E%d)
解決方法を見る コード SEAL-233
Low Material Supply Pressure (E%d)
解決方法を見る コード SEAL-234
No Material Supply Pressure (E%d)
解決方法を見る コード SEAL-235
Nozzle Clog or Down Stream Blockage (E%d)
解決方法を見る コード SEAL-236
Gun Cable Failure (E%d)
解決方法を見る コード SEAL-237
Flowmeter/Booster Pump Failure (E%d)
解決方法を見る コード SEAL-238
Nozzle Pressure Transducer Failure (E%d)
解決方法を見る コード SEAL-239
Flowmeter cable Failure (E%d)
解決方法を見る コード SEAL-240
Upstream Pressure Transducer Failed (E%d)
解決方法を見る コード SEAL-241
Upstream Pressure Transducer Cable Failed (E%d)
解決方法を見る コード SEAL-242
Robot Signal Out of Sequence (E%d)
解決方法を見る コード SEAL-243
Gun Failure (E%d)
解決方法を見る コード SEAL-244
Bead Defect Detected (E%d)
解決方法を見る コード SEAL-245
Joint Motion While Dispensing
解決方法を見る コード SEAL-246
Style ID communication timeout (E%s)
解決方法を見る コード SEAL-250
High Dispensed Volume (E%s)
解決方法を見る コード SEAL-251
Low Dispensed Volume (E%s)
解決方法を見る コード SEAL-252
High Material Supply Pressure (E%s)
解決方法を見る コード SEAL-253
Low Material Supply Pressure (E%s)
解決方法を見る コード SEAL-254
No Material Supply Pressure (E%s)
解決方法を見る コード SEAL-255
Nozzle Clog or Down Stream Blockage (E%s)
解決方法を見る コード SEAL-256
Gun Cable Failure (E%s)
解決方法を見る コード SEAL-257
Flowmeter/Booster Pump Failure (E%s)
解決方法を見る コード SEAL-258
Nozzle Pressure Transducer Failure (E%s)
解決方法を見る コード SEAL-259
Flowmeter cable Failure (E%s)
解決方法を見る コード SEAL-260
Upstream Pressure Transducer Failed (E%s)
解決方法を見る コード SEAL-261
Upstream Pressure Transducer Cable Failed (E%s)
解決方法を見る コード SEAL-262
Dispense IO Sequence error (E%s)
解決方法を見る コード SEAL-263
Gun Failure (E%s)
解決方法を見る コード SEAL-264
Bead Defect Detected (E%s)
解決方法を見る コード SEAL-265
Major Dispenser Fault on (E%s)
解決方法を見る コード SEAL-266
Minor Dispenser Fault on (E%s)
解決方法を見る コード SEAL-267
Volume dispensed out of range (E%s)
解決方法を見る コード SEAL-268
Flow rate is zero (E%d)
解決方法を見る コード SEAL-269
Flow command below minimum (E%d)
解決方法を見る コード SEAL-270
Flow command above maximum (E%d)
解決方法を見る コード SEAL-271
Channel 2 analog is zero (E%d)
解決方法を見る コード SEAL-272
Channel 2 analog is below set point (E%d)
解決方法を見る コード SEAL-273
Channel 2 analog is above set point (E%d)
解決方法を見る コード SEAL-274
Dispenser not pressurized (E%s)
解決方法を見る コード SEAL-275
Dispenser meter not full (E%s)
解決方法を見る コード SEAL-276
Dispense meter not pressurized (E%s)
解決方法を見る コード SEAL-277
Drum empty (E%s)
解決方法を見る コード SEAL-278
Auto purge requested (E%s)
解決方法を見る コード SEAL-279
primer check passed (E%s)
解決方法を見る コード SEAL-280
Primer check failed (E%s)
解決方法を見る コード SEAL-281
Felt not advanced (E%s)
解決方法を見る コード SEAL-282
Meter Empty (E%d, Mtr %s)
解決方法を見る コード SEAL-283
Both Meters Empty
解決方法を見る コード SEAL-284
Plugged Tip Detected (E%d)
解決方法を見る コード SEAL-285
Premature Reload Term (E%d)
解決方法を見る コード SEAL-287
Cmd prs NOT achieved (E%d)
解決方法を見る コード SEAL-288
Application setup not done
解決方法を見る コード SEAL-289
Macro table already full
解決方法を見る コード SEAL-290
Invalid call to SL__INST
解決方法を見る コード SEAL-291
No start sealing input defined
解決方法を見る コード SEAL-292
Max Error table entry exceeded
解決方法を見る コード SEAL-293
No SLSHELL has been loaded!!!
解決方法を見る コード SEAL-294
Style bit is out of range (E%s)
解決方法を見る コード SEAL-295
I/O not assigned Eq%s
解決方法を見る