Back to all Siemens models Search all database
Siemens SINUMERIK 840D CNC
Siemens SINUMERIK 840D CNC Error Codes
Complete alarm and error code reference for the Siemens SINUMERIK 840D CNC. Browse all 4014 documented fault codes below, each linking to a detailed troubleshooting guide.
Search this section
Search Siemens SINUMERIK 840D CNC
Search all 4014 Siemens SINUMERIK 840D CNC codes without changing pages.
Complete Alarm List (Page 4 of 21)
Code 14182
[Channel %1: ] Block %2 different values under H and D addresses
View solution Code 14183
[Channel %1: ] Block %2 H and D addresses must be programmed after Siemens offset
View solution Code 14184
[Channel %1: ] Block %2 G44 is not possible with tool offset H99
View solution Code 14185
[Channel %1: ] Block %2 D number %3 is not defined
View solution Code 14186
[Channel %1: ] Block %2 ISO2 mode, and toolcarrier or tool adapter are both active (identifier %3)
View solution Code 14190
[Channel %1: ] Block %2 H number with G49
View solution Code 14195
[Channel %1: ] Block %2 D number with G49
View solution Code 14196
[Channel %1: ] Block %2 error %3 on interpreting the contents of $SC_CUTDIRMOD
View solution Code 14197
[Channel %1: ] Block %2 D number and H number programmed simultaneously
View solution Code 14198
[Channel %1: ] Block %2 illegal change of tool direction with tool offset
View solution Code 14199
[Channel %1: ] Block %2 illegal plane change for tool with diameter component
View solution Code 14200
[Channel %1: ] Block %2 negative polar radius
View solution Code 14210
[Channel %1: ] Block %2 polar angle too large
View solution Code 14250
[Channel %1: ] Block %2 negative pole radius
View solution Code 14260
[Channel %1: ] Block %2 pole angle too large
View solution Code 14270
[Channel %1: ] Block %2 pole programmed incorrectly
View solution Code 14280
[Channel %1: ] Block %2 polar coordinates programmed incorrectly
View solution Code 14290
[Channel %1: ] Block %2 polynominal degree greater than 5 programmed for polynominal interpolation
View solution Code 14300
[Channel %1: ] Block %2 overlaid handwheel motion activated incorrectly
View solution Code 14320
[Channel %3: ] Axis %4: handwheel %1 used twice (%2)
View solution Code 14400
[Channel %1: ] Block %2 tool radius compensation active at transformation switchover
View solution Code 14401
[Channel %1: ] Block %2 transformation not available
View solution Code 14402
[Channel %1: ] Block %2 spline active at transformation change
View solution Code 14403
[Channel %1: ] Block %2 preprocessing and main run might not be synchronized
View solution Code 14404
[Channel %1: ] Block %2 illegal parameterization of transformation
View solution Code 14410
[Channel %1: ] Block %2 spline active at geometry axis changeover
View solution Code 14411
[Channel %1: ] Block %2 tool radius compensation active at geometry axis changeover
View solution Code 14412
[Channel %1: ] Block %2 transformation active at geometry axis changeover
View solution Code 14413
[Channel %1: ] Block %2 fine tool correction: changeover geometry/channel axis not allowed
View solution Code 14414
[Channel %1: ] Block %2 GEOAX function: incorrect call
View solution Code 14415
[Channel %1: ] Block %2 tangent control: changeover geometry/channel axis not allowed
View solution Code 14420
[Channel %1: ] Block %2 index axis %3 frame not allowed
View solution Code 14430
[Channel %1: ] Block %2 tangential axis %3 must not be traversed as POS axis
View solution Code 14432
[Channel %1: ] Block %2 rounding length for tangential axis %3 is zero.
View solution Code 14434
[Channel %1: ] Block %2 rel. lift-off path for tangential axis %3 is invalid
View solution Code 14500
[Channel %1: ] Block %2 illegal DE F or PROC instruction in the part program
View solution Code 14510
[Channel %1: ] Block %2 PROC instruction missing on subroutine call
View solution Code 14520
[Channel %1: ] Block %2 illegal PROC instruction in data definition section
View solution Code 14530
[Channel %1: ] Block %2 EXTERN and PROC instruction do not correspond
View solution Code 14540
[Channel %1: ] Block %2 contour t ool: the min. limit angle has been programmed more than once (edge D%3)
View solution Code 14541
[Channel %1: ] Block %2 contour tool: the max. limit angle has been programmed more than once (edge D%3)
View solution Code 14542
[Channel %1: ] Block %2 contour tool : the min. limit angle has not been programmed
View solution Code 14543
[Channel %1: ] Block %2 contour tool: the max. limit angle has not been programmed
View solution Code 14544
[Channel %1: ] Block %2 contour tool: edge D%3 is not positioned between the two border edges
View solution Code 14545
[Channel %1: ] Block %2 contour tool: edge D%3 completely encircles edge D%4
View solution Code 14546
[Channel %1: ] Block %2 contour tool: edge D%3 defines a concave corner
View solution Code 14547
[Channel %1: ] Block %2 contour tool: checksum erroneous or not available
View solution Code 14548
[Channel %1: ] Block %2 contour tool: negative radius in edge D%3 is not allowed
View solution Code 14549
[Channel %1: ] Block %2 contour tool: impermissible programming. Code no. %3
View solution Code 14550
[Channel %1: ] Block %2 contour tool: impermissible tool contour change. Code no. %3
View solution Code 14551
[Channel %1: ] Block %2 contour tool: angle area of edge D%3 larger than 359 degrees
View solution Code 14600
[Channel %1: ] Block %2 reload buffer %3 cannot be established
View solution Code 14601
[Channel %1: ] Block %2 reload buffer could not be deleted
View solution Code 14602
[Channel %1: ] Block %2 timeout while reloading from external.
View solution Code 14603
[Channel %1: ] Block %2 timeout during execution from external source.
View solution Code 14610
[Channel %1: ] Block %2 compensation block not possible
View solution Code 14615
[Channel %1: ] An error occurred while handling the function 'syntax check': identifier %3
View solution Code 14650
[Channel %1: ] Block %2 SETINT in struction with invalid ASUP input
View solution Code 14660
[Channel %1: ] Block %2 SETINT instruction with invalid priority
View solution Code 14700
[Channel %1: ] Block %2 timeout during command to interpreter
View solution Code 14701
[Channel %1: ] Block %2 number of available NC blocks reduced by %3
View solution Code 14710
[Channel %1: ] Block %2 error in initialization sequence in function %3
View solution Code 14711
[Channel %1: ] Transformation selection not possible as axis %2 not available
View solution Code 14720
[Channel %1: ] Block %2 axes for centerless transformation not available
View solution Code 14730
[Channel %1: ] Block %2 conflict at activation of centerless transformation
View solution Code 14740
[Channel %1: ] Block %2 no tool data available for centerless grinding
View solution Code 14745
[Channel %1: ] Block %2 centerless grinding not active
View solution Code 14750
[Channel %1: ] Block %2 too many auxiliary functions programmed
View solution Code 14751
[Channel %1: ] Block %2 resources for motion synchronous actions not sufficient (code: %3)
View solution Code 14752
[Channel %1: ] Block %2 DELDTG | STOPREOF conflict
View solution Code 14753
[Channel %1: ] Block %2 motion synchronous actions with illegal interpolation type
View solution Code 14754
[Channel %1: ] Block %2 motion synchronous actions and wrong feed type
View solution Code 14755
[Channel %1: ] Block %2 motion synchronous actions without traverse motion
View solution Code 14756
[Channel %1: ] Block %2 motion synchronous action and wrong value
View solution Code 14757
[Channel %1: ] Block %2 motion synchronous action and wrong type
View solution Code 14758
[Channel %1: ] Block %2 programmed value not available
View solution Code 14759
[Channel %1: ] Block %2 motion synchronous action and wrong axis type
View solution Code 14760
[Channel %1: ] Block %2 auxiliary function of a group programmed repeatedly
View solution Code 14761
[Channel %1: ] Block %2 motion sy nchronous action: DELDTG function not allowed with active tool radius compensation
View solution Code 14762
[Channel %1: ] Block %2 too many PLC variables programmed
View solution Code 14763
[Channel %1: ] Block %2 too many link variables programmed
View solution Code 14764
NCU link cannot transfer all link variables immediately
View solution Code 14765
NCU link cannot transfer all link variables
View solution Code 14766
NCU link is heavily loaded, impending memory shortage
View solution Code 14767
Machine data matching via NCU link not complete
View solution Code 14768
Axial auxiliary function for the NCU link cannot be output
View solution Code 14769
[Channel %1: ] Block %2 Spindle %3 Implicit auxiliary function %4 Buffer full
View solution Code 14770
[Channel %1: ] Block %2 auxiliary function programmed incorrectly
View solution Code 14780
[Channel %1: ] Block %2 unreleased option used (identification %3)
View solution Code 14782
[Channel %1: ] Block %2 non-active function used (identification %3)
View solution Code 14783
[Channel %1: ] Block %2 coordinate system-specific working area limitation is not active
View solution Code 14790
[Channel %1: ] Block %2 axis %3 programmed by PLC
View solution Code 14800
[Channel %1: ] Block %2 programmed path speed less or equal to zero
View solution Code 14810
[Channel %1: ] Block %2 negative axis speed programmed for positioning axis %3
View solution Code 14811
[Channel %1: ] Block %2 incorrect value range for acceleration of axis/spindle %3
View solution Code 14812
[Channel %1: ] Block %2 SOFTA not available for axis %3
View solution Code 14815
[Channel %1: ] Block %2 negative thread pitch change programmed
View solution Code 14820
[Channel %1: ] Block %2 negative value for maximum spindle speed programmed with constant cutting speed
View solution Code 14821
[Channel %1: ] Block %2 error in selection or deselection of GWPS
View solution Code 14822
[Channel %1: ] Block %2 incorrect programming of GWPS
View solution Code 14823
[Channel %1: ] Block %2 error on selection or deselection of tool monitoring
View solution Code 14824
[Channel %1: ] Block %2 conflict with GWPS
View solution Code 14830
[Channel %1: ] Block %2 wrong feed type selected
View solution Code 14840
[Channel %1: ] Block %2 incorrect value range for constant cutting speed
View solution Code 14850
[Channel %1: ] Block %2 changing the reference axis for a constant cutting speed not allowed
View solution Code 14860
[Channel %1 ] Block %2 Selection of the tool cutting rate not allowed. Cause %3
View solution Code 14861
[Channel %1 ] Block %2 SVC programmed, but no tool offset active
View solution Code 14862
[Channel %1 ] Block %2 SVC has been programmed, but the radius of the active tool correction is zero
View solution Code 14863
[Channel %1 ] Block %2 The programmed SVC value is zero or negative
View solution Code 14900
[Channel %1: ] Block %2 center point and end point programmed simultaneously
View solution Code 14910
[Channel %1: ] Block %2 invalid angle of aperture for programmed circle
View solution Code 14920
[Channel %1: ] Block %2 intermediate point of circle incorrect
View solution Code 15000
[Channel %1: ] Block %2 channel-sync command using illegal marker
View solution Code 15010
[Channel %1: ] Block %2 program coordination instruction with invalid channel number
View solution Code 15020
Channel %1 block %2 CHANDATA inst ruction cannot be executed. Channel %3 is not active
View solution Code 15021
[Channel %1: ] Block %2 CHANDATA instruction with invalid channel number
View solution Code 15025
CHANDATA(%2): channel is not acti ve. Channel data will be ignored.
View solution Code 15030
[Channel %1: ] Block %2 different measurement system settings
View solution Code 15100
[Channel %1: ] Block %2 REORG abort caused by log file overflow
View solution Code 15110
[Channel %1: ] Block %2 REORG not possible
View solution Code 15120
If a power failure occurs now, th e last data change d will be lost; index/buffer size = %1
View solution Code 15122
Power ON after power failure: %1 data were restored, of which %2 machine data, %3 errors.
View solution Code 15150
[Channel %1: ] Block %2 reload from external aborted
View solution Code 15160
[Channel %1: ] Block %2 wrong preprocessing configuration
View solution Code 15165
[Channel %1: ] Block %2 error when translating or interpreting Asup %3
View solution Code 15166
[Channel %1: ] User system asup _N_ASUP_SPF not available
View solution Code 15170
[Channel %1: ] Block %2 program %3 could not be compiled
View solution Code 15171
[Channel %1: ] Block %2 compiled program %3 older than the relevant subroutine
View solution Code 15172
[Channel %1: ] Block %2 subroutine %3. No interface available at time of preprocessing.
View solution Code 15173
[Channel %1: ] Block %2 variable %3 was unknown at the time of preprocessing.
View solution Code 15175
[Channel %1: ] Block %2 program %3. Interfaces could not be built
View solution Code 15176
[Channel %1: ] Block %2 Program%3 may only be executed after Power ON
View solution Code 15177
[Channel %1: ] Block %2 Error on preprocessing of program %3, error code: %4
View solution Code 15180
[Channel %1: ] Block %2: Error on editing program %3 as INI/DEF file.
View solution Code 15185
[Channel %1: ] %2 errors in INI file
View solution Code 15186
[Channel %1: ] %2 errors in GUD, macro or INI file
View solution Code 15187
[Channel %1: ] Error during execution of PROGEVENT file %3.
View solution Code 15188
[Channel %1: ] Error during execution of ASUB file %3.
View solution Code 15190
[Channel %1: ] Block %2 not enough free memory for subroutine call
View solution Code 15300
[Channel %1: ] Block %2 invalid number-of-passed-blocks during block search
View solution Code 15310
[Channel %1: ] Block %2 file requested during block search is not available
View solution Code 15320
[Channel %1: ] Block %2 invalid block search command
View solution Code 15330
[Channel %1: ] Block %2 invalid block number as search target
View solution Code 15340
[Channel %1: ] Block %2 invalid label as search target
View solution Code 15350
[Channel %1: ] Block %2 search target not found
View solution Code 15360
[Channel %1: ] Illegal target of block search (syntax error)
View solution Code 15370
[Channel %1: ] Target of block search not found
View solution Code 15380
[Channel %1: ] Block %2 illegal incremental programming in axis %3
View solution Code 15390
[Channel %1: ] Block %2 %3 not executed during block search
View solution Code 15395
[Channel %1: ] Master-slave not executable during block search
View solution Code 15400
[Channel %1: ] Block %2 selected initial INIT block does not exist
View solution Code 15410
[Channel %1: ] Block %2 initialization file contains invalid M function
View solution Code 15420
[Channel %1: ] Block %2 instruction in current mode not allowed
View solution Code 15450
[Channel %1: ] Block %2 compiled program cannot be stored
View solution Code 15460
[Channel %1: ] Block %2 syntax error when locking
View solution Code 15500
[Channel %1: ] Block %2 illegal angle of shear
View solution Code 15700
[Channel %1: ] Block %2 illegal cycle alarm number %3
View solution Code 15800
[Channel %1: ] Block %2 wrong starting conditions for CONTPRON/CONTDCON
View solution Code 15810
[Channel %1: ] Block %2 wrong array dimension for CONTPRON/CONTDCON
View solution Code 15900
[Channel %1: ] Block %2 touch probe not allowed
View solution Code 15910
[Channel %1: ] Block %2 touch probe not allowed
View solution Code 15950
[Channel %1: ] Block %2 no traverse motion programmed
View solution Code 15960
[Channel %1: ] Block %2 no traverse motion programmed
View solution Code 16000
[Channel %1: ] Block %2 invalid value for lifting direction
View solution Code 16005
[Channel %1: ] Block %2 invalid value for lifting distance
View solution Code 16010
[Channel %1: ] Block %2 machining stop after lift fast
View solution Code 16015
[Channel %1: ] Block %2 wrong axis identifier %3
View solution Code 16016
[Channel %1: ] Block %2 no retraction position programmed for axis %3
View solution Code 16017
Channel %1 Axis %2 Identifier %3, LIFTFAST ignores this axis, current axis not capable of retraction
View solution Code 16020
[Channel %1: ] Repositioning in block %2 is not possible
View solution Code 16025
[Channel %1: ] Block %2 impermissible axis exchange in REPOS command by axis %3.
View solution Code 16100
[Channel %1: ] Block %2 spindle %3 not available in the channel
View solution Code 16105
[Channel %1: ] Block %2 spindle %3 cannot be assigned
View solution Code 16110
[Channel %1: ] Block %2 spindle %3 for dwell time not in control mode
View solution Code 16111
[Channel %1: ] Block %2 spindle %3 No speed programmed
View solution Code 16112
[Channel %1: ] Block %2 foll owing spindle %3 Impermissible programming
View solution Code 16120
[Channel %1: ] Block %2 invalid index for tool fine compensation
View solution Code 16130
[Channel %1: ] Block %2 command not allowed with FTOCON
View solution Code 16140
[Channel %1: ] Block %2 FTOCON not allowed
View solution Code 16150
[Channel %1: ] Block %2 invalid spindle number with PUTFTOCF
View solution Code 16200
[Channel %1: ] Block %2 spline and polynominal interpolation not available
View solution Code 16300
[Channel %1: ] Block %2 denominator polynominal with zero places within parameter range not allowed
View solution Code 16400
[Channel %1: ] Block %2 positioning axis %3 cannot participate in spline
View solution Code 16410
[Channel %1: ] Block %2 axis %3 is not a geometry axis
View solution Code 16420
[Channel %1: ] Block %2 axis %3 programmed repeatedly
View solution Code 16421
[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block
View solution Code 16422
[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block
View solution Code 16423
[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block
View solution Code 16424
[Channel %1: ] Block %2 coordinate %3 programmed repeatedly in the block
View solution Code 16430
[Channel %1: ] Block %2 geometry axis %3 cannot traverse as positioning axis in rotated coordinate system
View solution Code 16440
[Channel %1: ] Block %2 rotation programmed for non-existent geometry axis
View solution Code 16500
[Channel %1: ] Block %2 chamfer or rounding negative
View solution Code 16510
[Channel %1: ] Block %2 no facing axis for diameter programming available
View solution Code 16520
[Channel %1: ] Axis %2, diameter programming active, function %3 is not executed
View solution Code 16600
[Channel %1: ] Block %2 spindle %3 gear stage change not possible
View solution Code 16670
[Channel %1: ] Block %2 following axis/spindle %3 maximum number of CP modules (%4) has been exceeded
View solution Code 16671
[Channel %1: ] Block %2 following axis/spindle %3 maximum number of CP modules (%4) has been exceeded
View solution Code 16672
[Channel %1: ] Block %2 leading ax is/spindle %3 ma ximum number of CP master values (%4) exceeded
View solution Code 16673
[Channel %1: ] Block %2 leading ax is/spindle %3 ma ximum number of CP master values (%4) exceeded
View solution Code 16675
Channel %1 block %2 following axi s/spindle %3 coupling module already defined in channel %4
View solution