Siemens SINUMERIK 840D CNC 错误代码

[Channel %1: ] JOG a circle is active and JOG circles deactivated

[Channel %1: ] Block %2 axis %3 is no machine axis

[Channel %1: ] Block %2 NCK-specific protection zone %3 wrong. Error code %4

[Channel %1: ] Block %2 channel-specific protection zone %3 incorrect. Error code %4

[Channel %1: ] Block %2 NCK protection zone %3 cannot be activated. Error code %4

[Channel %1: ] Block %2 channel-specific protection zone %3 cannot be activated. Error code %4

[Channel %1: ] Block %2 orientation of workpiece-related protection zone %3 does not correspond to the orientation of tool-related protection zone %4

[Channel %1: ] Block %2 serious error in definition of NCK-specific protection zone %3

[Channel %1: ] Block %2 serious error in definition of channel-specific protection zone %3

[Channel %1: ] Block %2 invalid value assigned to FXS[]

[Channel %1: ] Block %2 invalid value assigned to FXST[]

[Channel %1: ] Block %2 invalid value assigned to FXSW[]

[Channel %1: ] Block %2 curve table: block search stop not allowed with definition CTABDEF

[Channel %1: ] Block %2 curve table: table %3 does not exist

[Channel %1: ] Block %2 curve table: instruction CTABEND without CTABDEF not allowed

[Channel %1: ] Block %2 curve table: instru ction CTABDEF not within CTABDEF

[Channel %1: ] Block %2 curve table: instruction SUPA not within CTABDEF

[Channel %1: ] Block %2 frame: fine shift not possible

[Channel %1: ] Block %2 frame: illegal rotation

[Channel %1: ] Block %2 frame: illegal instruction

[Channel %1: ] Block %2 frame: fine shift not configured

[Channel %1: ] Block %2 frame: illegal switch over of geometry axes

[Channel %1: ] Block %2 frame: type conflict

[Channel %1: ] Block %2 language change not possible:%3

[Channel %1: ] Axis %2 reference cam not reached

[Channel %1: ] Axis %2 no cam signal present

[Channel %1: ] Axis %2 zero mark not found

[Channel %1: ] Axis %2 measuring system error

[Channel %1: ] Axis %2 reference mark missing

[Channel %1: ] Axis %2 reference point approach aborted

[Channel %1: ] Axis %2 reference point creep velocity not reached

[Channel %1: ] Axis %2 reference point approach requires 2 measuring systems

[Channel %1: ] Axis %2 reference point approach requires second referenced measuring system

[Channel %1: ] Axis %2 handwheel mode active

[Channel %1: ] Axis %2 handwheel mode not possible

[Channel %1: ] Axis %2 already active

[Channel %1: ] Axis %2 DRF, FTOCO N, external zero point offset not possible

[Channel %1: ] Axis %2 wrong index for indexing axis in JOG mode

[Channel %1: ] Master spindle not present in JOG mode

[Channel %1: ] Axis %2 no revoluti onal feedrate possible. Axis/spindle %3 stationary

[Channel %1: ] Block %2 revolutional feedrate for axis/spindle %3 is <= zero

[Channel %1: ] Axis %2 revolutional feedrate: illegal feed source

[Channel %1: ] Axis %2 already active due to %3

[Channel %1: ] Axis %2 cannot be traversed as geometry axis

[Channel %1: ] Axis %2 cannot be traversed as orientation axis

[Channel %1: ] Axis %2 already active

[Channel %1: ] Axis %2 orientation axes cannot be traversed without transformation

[Channel %1: ] Axis %2 selection of several axes with an active taper angle is not permitted.

[Channel %1: ] Master spindle not defined for geometry axes in JOG mode

[Channel %1: ] Axis %2 software limit switch %3

[Channel %1: ] Axis %2 working area limit %3

[Channel %1: ] Axis %2 is not an indexing axis

[Channel %1: ] Axis %2 cannot be repositioned

[Channel %1: ] Axis %2 wrong index position

[Channel %1: ] Axis %2 can currently not oscillate

[Channel %1: ] Axis %2 oscillating - mode change not possible

[Channel %1: ] Axis %2 programmed position is behind software limit switch %3

[Channel %1: ] Axis %2 programmed position is behind working area limit %3

[Channel %1: ] Axis %2 oscillation path %3 <= 0

[Channel %1: ] Axis %2 no handwheel assigned for override

[Channel %1: ] Axis %2 braking position cannot be accepted as a new reversing position

[Channel %1: ] Axis %2 coordinate system-specific working area limit %3

[Channel %1: ] Axis %2 programmed position lies behind the coordinate system-specific working area limit %3

[Channel %1: ] Contour handwheel: traverse direction or overtravel of beginning of block not allowed

Axis %1 travel to fixed stop not possible. Check programming and axis data.

Axis %1 has not reached fixed stop

Axis %1 travel to fixed stop still active

Axis %1 standstill monitoring at fi xed-stop end point has been triggered

Axis %1 function has been aborted

Axis %1 illegal to rque, current torque %2

Axis %1 brake test aborted, additional information %2

Axis %1 incorrect travel direction brake test

[Channel %1: ] :Invalid configuration for digitizing

Timeout during initia lization of communication with the digitizer

[Channel %1: ] No or invalid trafo at digitizing active

[Channel %1: ] Digitizing module does not support 3+2 axes digitizing

[Channel %1: ] Axes stopped by digitizer. Error code: %2

The digitizer has triggered an emergency stop.

Invalid data package received from the digitizer. Error codes %1, %2

Error in communication with the digitize r: status code of com-circuit: %1

Axis %1: too many compensation relations

Axis %1: Configuration error in compensation table %2

Compensation table %1: invalid axis assignment

Axis %1: different output assignment of multiplied tables

Axis %1: sum of compensation values too large

Axis %1: change of compensation value is too rapid

[Channel %1: ] Contour tunnel monitoring

[Channel %1: ] Block %2 motion-synchronous action: invalid marker

[Channel %1: ] Motion synchronous action: traversing of command axis %2 see NC alarm %3

[Channel %1: ] Motion synchronous action: illegal axis type

[Channel %1: ] Command axis %2: rotation of axis container already enabled

[Channel %1: ] Axis %2 command axis cannot be started as it is controlled by the PLC

[Channel %1: ] Block %2 motion synchronous action: system variable access not possible

[Channel %1: ] Block %2 motion synchronous action: arithmetic error

[Channel %1: ] Block %2 motion synchronous action: nesting depth exceeded

[Channel %1: ] Block %2 motion synchronous action: command not executable

[Channel %1: ] Block %2 motion synchronous action: internal error %3

[Channel %1: ] Block %2 motion synchronous action: illegal index

[Channel %1: ] Tool management: PLC terminates interrupted command

[Channel %1: ] Tool management: PLC can terminate only incorrectly aborted commands

[Channel %1: ] Machine data $AC_FIFO invalid

[Channel %1: ] Invalid spindle number %2 with tool fine compensation

[Channel %1: ] Spindle %2 no tool assigned

[Channel %1: ] No active tool

[Channel %1: ] PUTFTOC command not allowed with FTOCOF

[Channel %1: ] Block %3 spindle %2 wrong values for centerless grinding

[Channel %1: ] Block %3 spindle %2 support point beyond range limits

[Channel %1: ] Axis %2 orientation not possible

[Channel %1: ] Axis %2 Travel from hardware limit sw itch not possible. Reason: %3

[Channel %1: ] Axis %2 encoder %3 frequency exceeded

[Channel %1: ] Axis %2: enable reset, cause %3

Axis %1 measuring system changing

[Channel %1: ] Axis %2 hardware limit switch %3

[Channel %1: ] Axis %2 taken from traverse mode to follow-up mode

[Channel %1: ] Block %2 overlaid motion active at transformation switchover

[Channel %1: ] Block %2 transformation does not allow to traverse the pole

[Channel %1: ] As from block %2 transformation active: overlaid motion too great

[Channel %1: ] Block %2 transformation active: motion not possible

[Channel %1: ] Axis %2 Emergency braking ramp activated

[Channel %1: ] Axis %2 overlaid motion not allowed

[Channel %1: ] Block %2 axis %3 conflict between SYNACT: $AA_OFF and CORROF

[Channel %1: ] $AA_TOFF cleared

[Channel %1: ] Block %2 illegal change of tool direction with $AA_TOFF active

[Channel %1: ] Block %3 axis %2 touch probe already deflected, edge polarity not possible

[Channel %1: ] Block %3 axis %2 measurement not possible

[Channel %1: ] Block %3 axis %2 measurement aborted

[Channel %1: ] Block %3 axis %2 touch probe not deflected, illegal edge polarity

Output value at analog output no. %1 has been limited

Error during output of cam switching signals via timer

[Channel %1: ] Block %2 too many auxiliary functions programmed

[Channel %1: ] Workpiece setpoint %2 reached

[Channel %1: ] Block %3 spindle %2 gear stage change not possible

[Channel %1: ] Spindle %2 selected gear stage %3 not installed

[Channel %1: ] Block %3 spindle %2 actual gear stage differs from requested gear stage

[Channel %1: ] Block %3 spindle %2 change to programmed gear stage not possible

[Channel %1: ] Block %2 leading spindle %3 is in simulation.

[Channel %1: ] Block %2 dependent spindle %3 is in simulation.

[Channel %1: ] Block %2. The dynamics of leading spindle %3 and dependent spindle %4 is too variably

[Channel %1: ] Block %2 following spindle %3 No dynamic response for supplementary motion

[Channel %1: ] Block %2 following spindle %3 in the range of reduced acceleration capability

[Channel %1: ] Block %2 following axis/spindle %3 time monitoring: 'Synchronism fine' not reached

[Channel %1: ] Block %2 following axis/spindle %3 time monitoring: 'Synchronism coarse' not reached

[Channel %1: ] Block %3 spindle %2 gear step change position not reached

[Channel %1: ] Block %2 spindle %3 gear stage %4 is expected for axis mode.

[Channel %1: ] Block %2 foll owing spindle %3 Impermissible programming

[Channel %1: ] Block %2 Axis/spindle %3 'Correct synchronism' diagnostics %4

[Channel %1: ] Block %2 followin g spindle %3 PLC signal 'Enable override' has been set.

[Channel %1: ] Block %2 following axis/spindle %3 unable to determine the offset value (reason %4).

[Channel %1: ] Block %2 Axis/spindle %3 Synchronism override not possible (reason %4)

[Channel %1: ] Block %2 Axis/spindle %3 'Correct synchronism' is being ignored

[Channel %1: ] Block %2 Axis/Spindle %3 'Delete synchronism override' is being ignored

[Channel %1: ] Block %3 spindle %2 is not referenced with zero marker

Block %2 spindle/axis %3 not available in channel %1 because active in channel %4

[Channel %1: ] Block %3 spindle %2 no transition from speed control mode to position control mode

[Channel %1: ] Block %3 spindle %2 reference mark not found

[Channel %1: ] Block %3 spindle %2 no standstill on block change

[Channel %1: ] Block %3 spindle %2 reference mode not supported

[Channel %1: ] Block %3 spindle %2 improper punching signal

[Channel %1: ] Block %3 spindle %2 configured positioning speed is too high

[Channel %1: ] Block %2 for following spindle %3 coupling as leading spindle/axis already existing

[Channel %1: ] Block %2 for leading spindle %3 coupling as following spindle/axis already existing

[Channel %1: ] Position control expected for axis/spindle %2

[Channel %1: ] Axis %2 reference point approach: zero marker search velocity (MD) is not reached

[Channel %1: ] Axis %2 reference point approach: zero marker search velocity (MD) is too high

[Channel %1: ] Tool management: Tool motion is not possible as tool %2 is not in magazine %4.

[Channel %1: ] Tool management: Tool change is not possible as tool %2 is not in magazine %4.

[Channel %1: ] Tool management: tool change not possible since there is no tool available in tool group %2

[Channel %1: ] Block %2 tool management: no tool available in tool group %3

[Channel %1: ] Block %2 tool management: No tool available in tool group %3, program %4

[TO unit %1: ] Please change tool %2 into magazine. Repeat data backup

[TO unit %1: ] Tool %2 is active, but not in the magazine area under consideration

[Channel %1: ] Block %3 spindle %2 chuck speed exceeded

[Channel %1: ] Block %3 spindle %2 maximum speed for encoder resynchronization exceeded

[Channel %1: ] Block %3 spindle %2 maximum speed for position control exceeded

[Channel %1: ] Spindle %2 axis stopped during tapping

[Channel %1: ] Spindle %2 axis stopped during thread cutting

[Channel %1: ] Spindle %2 thread might be damaged

[Channel %1: ] Block %2 maximum tapping speed reached

[Channel %1: ] Block %2 zero velocity of thread axis at position %3 reached

[Channel %1: ] In block %2: Prog. acceleration path too short %3, %4 required

[Channel %1: ] Spindle operation for transformed spindle/axis %2 not possible (reason: error code %3).

Channel %1 Spindle %2 DBB30 function not possible (cause: error code %3)

Channel %1 Spindle %2 Error on gear stage change (cause: error code %3)

Channel %1 Spindle %2 FC18 function not possible (cause: error code %3)

[Channel %1: ] Block %2 PUTFTOCF command could not be transferred

[Channel %1: ] Axis %2 PRESET not allowed during traverse motion

[Channel %1: ] Axis %2 PRESET: illegal value

[Channel %1: ] Option 'contour handwheel' not set

Axis %1 hardware fault of active encoder

Axis %1 hardware fault of passive encoder

Axis %1 pollution of measuring system

Axis %1 pollution of passive encoder

Axis %1 zero mark monitoring of active encoder

Axis %1 zero mark moni toring of passive encoder

Axis %1 encoder %2 warning %3

Axis %1 actual velocity alarm limit

Axis %1 actual velocity warning limit

Axis %1 standstill monitoring

Axis %1 standstill monitori ng during torque/force limitation

Axis %1 contour monitoring