Zurück zu allen Siemens Modellen Search all database
Siemens SINUMERIK 840D CNC
Siemens SINUMERIK 840D CNC Fehlercodes
Vollständige Alarm- und Fehlercode-Referenz für die Siemens SINUMERIK 840D CNC. Durchsuchen Sie unten alle 4014 dokumentierten Fehlercodes, die jeweils zu einer detaillierten Anleitung zur Fehlerbehebung führen.
Search this section
Search Siemens SINUMERIK 840D CNC
Search all 4014 Siemens SINUMERIK 840D CNC codes without changing pages.
Vollständige Alarmliste (Page 4 of 21)
Code 14182
[Channel %1: ] Block %2 different values under H and D addresses
Lösung ansehen Code 14183
[Channel %1: ] Block %2 H and D addresses must be programmed after Siemens offset
Lösung ansehen Code 14184
[Channel %1: ] Block %2 G44 is not possible with tool offset H99
Lösung ansehen Code 14185
[Channel %1: ] Block %2 D number %3 is not defined
Lösung ansehen Code 14186
[Channel %1: ] Block %2 ISO2 mode, and toolcarrier or tool adapter are both active (identifier %3)
Lösung ansehen Code 14190
[Channel %1: ] Block %2 H number with G49
Lösung ansehen Code 14195
[Channel %1: ] Block %2 D number with G49
Lösung ansehen Code 14196
[Channel %1: ] Block %2 error %3 on interpreting the contents of $SC_CUTDIRMOD
Lösung ansehen Code 14197
[Channel %1: ] Block %2 D number and H number programmed simultaneously
Lösung ansehen Code 14198
[Channel %1: ] Block %2 illegal change of tool direction with tool offset
Lösung ansehen Code 14199
[Channel %1: ] Block %2 illegal plane change for tool with diameter component
Lösung ansehen Code 14200
[Channel %1: ] Block %2 negative polar radius
Lösung ansehen Code 14210
[Channel %1: ] Block %2 polar angle too large
Lösung ansehen Code 14250
[Channel %1: ] Block %2 negative pole radius
Lösung ansehen Code 14260
[Channel %1: ] Block %2 pole angle too large
Lösung ansehen Code 14270
[Channel %1: ] Block %2 pole programmed incorrectly
Lösung ansehen Code 14280
[Channel %1: ] Block %2 polar coordinates programmed incorrectly
Lösung ansehen Code 14290
[Channel %1: ] Block %2 polynominal degree greater than 5 programmed for polynominal interpolation
Lösung ansehen Code 14300
[Channel %1: ] Block %2 overlaid handwheel motion activated incorrectly
Lösung ansehen Code 14320
[Channel %3: ] Axis %4: handwheel %1 used twice (%2)
Lösung ansehen Code 14400
[Channel %1: ] Block %2 tool radius compensation active at transformation switchover
Lösung ansehen Code 14401
[Channel %1: ] Block %2 transformation not available
Lösung ansehen Code 14402
[Channel %1: ] Block %2 spline active at transformation change
Lösung ansehen Code 14403
[Channel %1: ] Block %2 preprocessing and main run might not be synchronized
Lösung ansehen Code 14404
[Channel %1: ] Block %2 illegal parameterization of transformation
Lösung ansehen Code 14410
[Channel %1: ] Block %2 spline active at geometry axis changeover
Lösung ansehen Code 14411
[Channel %1: ] Block %2 tool radius compensation active at geometry axis changeover
Lösung ansehen Code 14412
[Channel %1: ] Block %2 transformation active at geometry axis changeover
Lösung ansehen Code 14413
[Channel %1: ] Block %2 fine tool correction: changeover geometry/channel axis not allowed
Lösung ansehen Code 14414
[Channel %1: ] Block %2 GEOAX function: incorrect call
Lösung ansehen Code 14415
[Channel %1: ] Block %2 tangent control: changeover geometry/channel axis not allowed
Lösung ansehen Code 14420
[Channel %1: ] Block %2 index axis %3 frame not allowed
Lösung ansehen Code 14430
[Channel %1: ] Block %2 tangential axis %3 must not be traversed as POS axis
Lösung ansehen Code 14432
[Channel %1: ] Block %2 rounding length for tangential axis %3 is zero.
Lösung ansehen Code 14434
[Channel %1: ] Block %2 rel. lift-off path for tangential axis %3 is invalid
Lösung ansehen Code 14500
[Channel %1: ] Block %2 illegal DE F or PROC instruction in the part program
Lösung ansehen Code 14510
[Channel %1: ] Block %2 PROC instruction missing on subroutine call
Lösung ansehen Code 14520
[Channel %1: ] Block %2 illegal PROC instruction in data definition section
Lösung ansehen Code 14530
[Channel %1: ] Block %2 EXTERN and PROC instruction do not correspond
Lösung ansehen Code 14540
[Channel %1: ] Block %2 contour t ool: the min. limit angle has been programmed more than once (edge D%3)
Lösung ansehen Code 14541
[Channel %1: ] Block %2 contour tool: the max. limit angle has been programmed more than once (edge D%3)
Lösung ansehen Code 14542
[Channel %1: ] Block %2 contour tool : the min. limit angle has not been programmed
Lösung ansehen Code 14543
[Channel %1: ] Block %2 contour tool: the max. limit angle has not been programmed
Lösung ansehen Code 14544
[Channel %1: ] Block %2 contour tool: edge D%3 is not positioned between the two border edges
Lösung ansehen Code 14545
[Channel %1: ] Block %2 contour tool: edge D%3 completely encircles edge D%4
Lösung ansehen Code 14546
[Channel %1: ] Block %2 contour tool: edge D%3 defines a concave corner
Lösung ansehen Code 14547
[Channel %1: ] Block %2 contour tool: checksum erroneous or not available
Lösung ansehen Code 14548
[Channel %1: ] Block %2 contour tool: negative radius in edge D%3 is not allowed
Lösung ansehen Code 14549
[Channel %1: ] Block %2 contour tool: impermissible programming. Code no. %3
Lösung ansehen Code 14550
[Channel %1: ] Block %2 contour tool: impermissible tool contour change. Code no. %3
Lösung ansehen Code 14551
[Channel %1: ] Block %2 contour tool: angle area of edge D%3 larger than 359 degrees
Lösung ansehen Code 14600
[Channel %1: ] Block %2 reload buffer %3 cannot be established
Lösung ansehen Code 14601
[Channel %1: ] Block %2 reload buffer could not be deleted
Lösung ansehen Code 14602
[Channel %1: ] Block %2 timeout while reloading from external.
Lösung ansehen Code 14603
[Channel %1: ] Block %2 timeout during execution from external source.
Lösung ansehen Code 14610
[Channel %1: ] Block %2 compensation block not possible
Lösung ansehen Code 14615
[Channel %1: ] An error occurred while handling the function 'syntax check': identifier %3
Lösung ansehen Code 14650
[Channel %1: ] Block %2 SETINT in struction with invalid ASUP input
Lösung ansehen Code 14660
[Channel %1: ] Block %2 SETINT instruction with invalid priority
Lösung ansehen Code 14700
[Channel %1: ] Block %2 timeout during command to interpreter
Lösung ansehen Code 14701
[Channel %1: ] Block %2 number of available NC blocks reduced by %3
Lösung ansehen Code 14710
[Channel %1: ] Block %2 error in initialization sequence in function %3
Lösung ansehen Code 14711
[Channel %1: ] Transformation selection not possible as axis %2 not available
Lösung ansehen Code 14720
[Channel %1: ] Block %2 axes for centerless transformation not available
Lösung ansehen Code 14730
[Channel %1: ] Block %2 conflict at activation of centerless transformation
Lösung ansehen Code 14740
[Channel %1: ] Block %2 no tool data available for centerless grinding
Lösung ansehen Code 14745
[Channel %1: ] Block %2 centerless grinding not active
Lösung ansehen Code 14750
[Channel %1: ] Block %2 too many auxiliary functions programmed
Lösung ansehen Code 14751
[Channel %1: ] Block %2 resources for motion synchronous actions not sufficient (code: %3)
Lösung ansehen Code 14752
[Channel %1: ] Block %2 DELDTG | STOPREOF conflict
Lösung ansehen Code 14753
[Channel %1: ] Block %2 motion synchronous actions with illegal interpolation type
Lösung ansehen Code 14754
[Channel %1: ] Block %2 motion synchronous actions and wrong feed type
Lösung ansehen Code 14755
[Channel %1: ] Block %2 motion synchronous actions without traverse motion
Lösung ansehen Code 14756
[Channel %1: ] Block %2 motion synchronous action and wrong value
Lösung ansehen Code 14757
[Channel %1: ] Block %2 motion synchronous action and wrong type
Lösung ansehen Code 14758
[Channel %1: ] Block %2 programmed value not available
Lösung ansehen Code 14759
[Channel %1: ] Block %2 motion synchronous action and wrong axis type
Lösung ansehen Code 14760
[Channel %1: ] Block %2 auxiliary function of a group programmed repeatedly
Lösung ansehen Code 14761
[Channel %1: ] Block %2 motion sy nchronous action: DELDTG function not allowed with active tool radius compensation
Lösung ansehen Code 14762
[Channel %1: ] Block %2 too many PLC variables programmed
Lösung ansehen Code 14763
[Channel %1: ] Block %2 too many link variables programmed
Lösung ansehen Code 14764
NCU link cannot transfer all link variables immediately
Lösung ansehen Code 14765
NCU link cannot transfer all link variables
Lösung ansehen Code 14766
NCU link is heavily loaded, impending memory shortage
Lösung ansehen Code 14767
Machine data matching via NCU link not complete
Lösung ansehen Code 14768
Axial auxiliary function for the NCU link cannot be output
Lösung ansehen Code 14769
[Channel %1: ] Block %2 Spindle %3 Implicit auxiliary function %4 Buffer full
Lösung ansehen Code 14770
[Channel %1: ] Block %2 auxiliary function programmed incorrectly
Lösung ansehen Code 14780
[Channel %1: ] Block %2 unreleased option used (identification %3)
Lösung ansehen Code 14782
[Channel %1: ] Block %2 non-active function used (identification %3)
Lösung ansehen Code 14783
[Channel %1: ] Block %2 coordinate system-specific working area limitation is not active
Lösung ansehen Code 14790
[Channel %1: ] Block %2 axis %3 programmed by PLC
Lösung ansehen Code 14800
[Channel %1: ] Block %2 programmed path speed less or equal to zero
Lösung ansehen Code 14810
[Channel %1: ] Block %2 negative axis speed programmed for positioning axis %3
Lösung ansehen Code 14811
[Channel %1: ] Block %2 incorrect value range for acceleration of axis/spindle %3
Lösung ansehen Code 14812
[Channel %1: ] Block %2 SOFTA not available for axis %3
Lösung ansehen Code 14815
[Channel %1: ] Block %2 negative thread pitch change programmed
Lösung ansehen Code 14820
[Channel %1: ] Block %2 negative value for maximum spindle speed programmed with constant cutting speed
Lösung ansehen Code 14821
[Channel %1: ] Block %2 error in selection or deselection of GWPS
Lösung ansehen Code 14822
[Channel %1: ] Block %2 incorrect programming of GWPS
Lösung ansehen Code 14823
[Channel %1: ] Block %2 error on selection or deselection of tool monitoring
Lösung ansehen Code 14824
[Channel %1: ] Block %2 conflict with GWPS
Lösung ansehen Code 14830
[Channel %1: ] Block %2 wrong feed type selected
Lösung ansehen Code 14840
[Channel %1: ] Block %2 incorrect value range for constant cutting speed
Lösung ansehen Code 14850
[Channel %1: ] Block %2 changing the reference axis for a constant cutting speed not allowed
Lösung ansehen Code 14860
[Channel %1 ] Block %2 Selection of the tool cutting rate not allowed. Cause %3
Lösung ansehen Code 14861
[Channel %1 ] Block %2 SVC programmed, but no tool offset active
Lösung ansehen Code 14862
[Channel %1 ] Block %2 SVC has been programmed, but the radius of the active tool correction is zero
Lösung ansehen Code 14863
[Channel %1 ] Block %2 The programmed SVC value is zero or negative
Lösung ansehen Code 14900
[Channel %1: ] Block %2 center point and end point programmed simultaneously
Lösung ansehen Code 14910
[Channel %1: ] Block %2 invalid angle of aperture for programmed circle
Lösung ansehen Code 14920
[Channel %1: ] Block %2 intermediate point of circle incorrect
Lösung ansehen Code 15000
[Channel %1: ] Block %2 channel-sync command using illegal marker
Lösung ansehen Code 15010
[Channel %1: ] Block %2 program coordination instruction with invalid channel number
Lösung ansehen Code 15020
Channel %1 block %2 CHANDATA inst ruction cannot be executed. Channel %3 is not active
Lösung ansehen Code 15021
[Channel %1: ] Block %2 CHANDATA instruction with invalid channel number
Lösung ansehen Code 15025
CHANDATA(%2): channel is not acti ve. Channel data will be ignored.
Lösung ansehen Code 15030
[Channel %1: ] Block %2 different measurement system settings
Lösung ansehen Code 15100
[Channel %1: ] Block %2 REORG abort caused by log file overflow
Lösung ansehen Code 15110
[Channel %1: ] Block %2 REORG not possible
Lösung ansehen Code 15120
If a power failure occurs now, th e last data change d will be lost; index/buffer size = %1
Lösung ansehen Code 15122
Power ON after power failure: %1 data were restored, of which %2 machine data, %3 errors.
Lösung ansehen Code 15150
[Channel %1: ] Block %2 reload from external aborted
Lösung ansehen Code 15160
[Channel %1: ] Block %2 wrong preprocessing configuration
Lösung ansehen Code 15165
[Channel %1: ] Block %2 error when translating or interpreting Asup %3
Lösung ansehen Code 15166
[Channel %1: ] User system asup _N_ASUP_SPF not available
Lösung ansehen Code 15170
[Channel %1: ] Block %2 program %3 could not be compiled
Lösung ansehen Code 15171
[Channel %1: ] Block %2 compiled program %3 older than the relevant subroutine
Lösung ansehen Code 15172
[Channel %1: ] Block %2 subroutine %3. No interface available at time of preprocessing.
Lösung ansehen Code 15173
[Channel %1: ] Block %2 variable %3 was unknown at the time of preprocessing.
Lösung ansehen Code 15175
[Channel %1: ] Block %2 program %3. Interfaces could not be built
Lösung ansehen Code 15176
[Channel %1: ] Block %2 Program%3 may only be executed after Power ON
Lösung ansehen Code 15177
[Channel %1: ] Block %2 Error on preprocessing of program %3, error code: %4
Lösung ansehen Code 15180
[Channel %1: ] Block %2: Error on editing program %3 as INI/DEF file.
Lösung ansehen Code 15185
[Channel %1: ] %2 errors in INI file
Lösung ansehen Code 15186
[Channel %1: ] %2 errors in GUD, macro or INI file
Lösung ansehen Code 15187
[Channel %1: ] Error during execution of PROGEVENT file %3.
Lösung ansehen Code 15188
[Channel %1: ] Error during execution of ASUB file %3.
Lösung ansehen Code 15190
[Channel %1: ] Block %2 not enough free memory for subroutine call
Lösung ansehen Code 15300
[Channel %1: ] Block %2 invalid number-of-passed-blocks during block search
Lösung ansehen Code 15310
[Channel %1: ] Block %2 file requested during block search is not available
Lösung ansehen Code 15320
[Channel %1: ] Block %2 invalid block search command
Lösung ansehen Code 15330
[Channel %1: ] Block %2 invalid block number as search target
Lösung ansehen Code 15340
[Channel %1: ] Block %2 invalid label as search target
Lösung ansehen Code 15350
[Channel %1: ] Block %2 search target not found
Lösung ansehen Code 15360
[Channel %1: ] Illegal target of block search (syntax error)
Lösung ansehen Code 15370
[Channel %1: ] Target of block search not found
Lösung ansehen Code 15380
[Channel %1: ] Block %2 illegal incremental programming in axis %3
Lösung ansehen Code 15390
[Channel %1: ] Block %2 %3 not executed during block search
Lösung ansehen Code 15395
[Channel %1: ] Master-slave not executable during block search
Lösung ansehen Code 15400
[Channel %1: ] Block %2 selected initial INIT block does not exist
Lösung ansehen Code 15410
[Channel %1: ] Block %2 initialization file contains invalid M function
Lösung ansehen Code 15420
[Channel %1: ] Block %2 instruction in current mode not allowed
Lösung ansehen Code 15450
[Channel %1: ] Block %2 compiled program cannot be stored
Lösung ansehen Code 15460
[Channel %1: ] Block %2 syntax error when locking
Lösung ansehen Code 15500
[Channel %1: ] Block %2 illegal angle of shear
Lösung ansehen Code 15700
[Channel %1: ] Block %2 illegal cycle alarm number %3
Lösung ansehen Code 15800
[Channel %1: ] Block %2 wrong starting conditions for CONTPRON/CONTDCON
Lösung ansehen Code 15810
[Channel %1: ] Block %2 wrong array dimension for CONTPRON/CONTDCON
Lösung ansehen Code 15900
[Channel %1: ] Block %2 touch probe not allowed
Lösung ansehen Code 15910
[Channel %1: ] Block %2 touch probe not allowed
Lösung ansehen Code 15950
[Channel %1: ] Block %2 no traverse motion programmed
Lösung ansehen Code 15960
[Channel %1: ] Block %2 no traverse motion programmed
Lösung ansehen Code 16000
[Channel %1: ] Block %2 invalid value for lifting direction
Lösung ansehen Code 16005
[Channel %1: ] Block %2 invalid value for lifting distance
Lösung ansehen Code 16010
[Channel %1: ] Block %2 machining stop after lift fast
Lösung ansehen Code 16015
[Channel %1: ] Block %2 wrong axis identifier %3
Lösung ansehen Code 16016
[Channel %1: ] Block %2 no retraction position programmed for axis %3
Lösung ansehen Code 16017
Channel %1 Axis %2 Identifier %3, LIFTFAST ignores this axis, current axis not capable of retraction
Lösung ansehen Code 16020
[Channel %1: ] Repositioning in block %2 is not possible
Lösung ansehen Code 16025
[Channel %1: ] Block %2 impermissible axis exchange in REPOS command by axis %3.
Lösung ansehen Code 16100
[Channel %1: ] Block %2 spindle %3 not available in the channel
Lösung ansehen Code 16105
[Channel %1: ] Block %2 spindle %3 cannot be assigned
Lösung ansehen Code 16110
[Channel %1: ] Block %2 spindle %3 for dwell time not in control mode
Lösung ansehen Code 16111
[Channel %1: ] Block %2 spindle %3 No speed programmed
Lösung ansehen Code 16112
[Channel %1: ] Block %2 foll owing spindle %3 Impermissible programming
Lösung ansehen Code 16120
[Channel %1: ] Block %2 invalid index for tool fine compensation
Lösung ansehen Code 16130
[Channel %1: ] Block %2 command not allowed with FTOCON
Lösung ansehen Code 16140
[Channel %1: ] Block %2 FTOCON not allowed
Lösung ansehen Code 16150
[Channel %1: ] Block %2 invalid spindle number with PUTFTOCF
Lösung ansehen Code 16200
[Channel %1: ] Block %2 spline and polynominal interpolation not available
Lösung ansehen Code 16300
[Channel %1: ] Block %2 denominator polynominal with zero places within parameter range not allowed
Lösung ansehen Code 16400
[Channel %1: ] Block %2 positioning axis %3 cannot participate in spline
Lösung ansehen Code 16410
[Channel %1: ] Block %2 axis %3 is not a geometry axis
Lösung ansehen Code 16420
[Channel %1: ] Block %2 axis %3 programmed repeatedly
Lösung ansehen Code 16421
[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block
Lösung ansehen Code 16422
[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block
Lösung ansehen Code 16423
[Channel %1: ] Block %2 angle %3 programmed repeatedly in the block
Lösung ansehen Code 16424
[Channel %1: ] Block %2 coordinate %3 programmed repeatedly in the block
Lösung ansehen Code 16430
[Channel %1: ] Block %2 geometry axis %3 cannot traverse as positioning axis in rotated coordinate system
Lösung ansehen Code 16440
[Channel %1: ] Block %2 rotation programmed for non-existent geometry axis
Lösung ansehen Code 16500
[Channel %1: ] Block %2 chamfer or rounding negative
Lösung ansehen Code 16510
[Channel %1: ] Block %2 no facing axis for diameter programming available
Lösung ansehen Code 16520
[Channel %1: ] Axis %2, diameter programming active, function %3 is not executed
Lösung ansehen Code 16600
[Channel %1: ] Block %2 spindle %3 gear stage change not possible
Lösung ansehen Code 16670
[Channel %1: ] Block %2 following axis/spindle %3 maximum number of CP modules (%4) has been exceeded
Lösung ansehen Code 16671
[Channel %1: ] Block %2 following axis/spindle %3 maximum number of CP modules (%4) has been exceeded
Lösung ansehen Code 16672
[Channel %1: ] Block %2 leading ax is/spindle %3 ma ximum number of CP master values (%4) exceeded
Lösung ansehen Code 16673
[Channel %1: ] Block %2 leading ax is/spindle %3 ma ximum number of CP master values (%4) exceeded
Lösung ansehen Code 16675
Channel %1 block %2 following axi s/spindle %3 coupling module already defined in channel %4
Lösung ansehen