Siemens SINUMERIK 840D CNC エラーコード

Axis %1 speed setpoint limitation

Axis %1 drift value too large

Axis %1 positioning monitoring

Axis %1 measuring system switchover not possible

Axis %1 measuring systems differ considerably

Axis %1 selected encoder not available

Axis %1 requested se t of parame ters invalid

Axis %1 drive fault

Axis %1 waiting for drive

Axis %1 clamping monitoring

Axis %1 parameterization error: friction compensation

Axis %1 encoder %2 parameterization error: number of encoder marks

Axis %1 parameterization error: lead screw pitch

Axis %1 encoder %2 parameterization error: grid point distance with linear encoders

Axis %1 parameteriza tion error: output rating

Axis %1 encoder %2 encoder type/output type %3 not possible

Axis %1 QEC: invalid coarse step size

Axis %1 QEC: invalid fine step size

Axis %1 QEC: memory overflow

Axis %1 QEC: invalid acceleration characteristic

Axis %1 QEC: in valid measuring periods

Axis %1 QEC: feed forward control not active

Axis %1 machine data %2 invalid value

Axis %1 machine data %2[%3] invalid value

Axis %1 machine data %2 invalid value

Axis %1 machine data %2[%3] invalid value

Axis %1 setpoint output drive %2 used more than once

Axis %1 encoder %2 measurement not possible with this controller module

Axis %1 encoder %2 measurement with simulated encoder not possible

Axis %1 machine data %2 value changed

Axis %1 machine data %2[%3] value changed

Axis %1 SINAMICS drive parameter P2038 value is not allowed.

Axis %1 encoder %2 absolute position lost

Axis %1 configuration error master-slave

[Channel %1: ] Axis %2 master-slave not configured

Axis %1 parameter set change from %2 to %3 not possible

[Channel %1: ] In block %2 unanticipated stop crossed in continuous path mode

[Channel %1: ] In block %2: path velocity too high for auxiliary function output

[Channel %1: ] Block %2 interpolation problem in Look Ahead (module %3, identifier %4)

[Channel %1: ] Block %2 interpolation warning in Look Ahead (module %3, problem %4)

[Channel %1: ] Axis %2 cannot be controlled by the PLC, max. number exceeded

[Channel %1: ] Axis %2 cannot be controlled by the PLC

[Channel %1: ] Switching off PLC control of axis %2 not allowed in the current state

[Channel %1: ] Axis %2 not available for the NC program, as exclusively controlled by the PLC

[Channel %1: ] Axis %2 not available for NC program, firmly assigned PLC axis

Axis %1 drive %2 sign of life missing

Axis %1 drive %2 communication failure

Axis %1 drive %2 sign of life missing

Drive of axis %1 not found

Encoder %2 of axis %1 not found

[Channel %1: ] Axis %2 $AA_ESR_ENABLE = 1 but axis should be set to NEUTRAL

[Channel %1: ] Axis %2 is NEUTRAL and $AA_ESR_ENABLE = 1 should be set

[Channel %1: ] Axis %2, $AA_ESR_ENABLE = 1, axis exchange not executed in this state

[Channel %1: ] Axis %2, $AA_ESR_ENABLE = 1 should be set, but MD37500 $MA_ESR_REACTION = 0

[Channel %1: ] Axis %2, $AC_ESR_TRIGGER triggered but axis is NEUTRAL and cannot execute ESR

[Channel %1: ] Block %2: The names of the kinematic chains $NK_CHAIN_NAME[%3] and $NK_C HAIN_NAME[%4] are the same]

[Channel %1: ] Block %2: The names of the kinematic chain links $NK_NAME[%3] and $NK_NAME[%4] are the same]

[Channel %1: ] Block %2: The chain element %3 referred to in $NK_NEXT[%4] is already contained in the chain

[Channel %1: ] Block %2: The chain element %3, referred to in $NK_1ST_ELEM[%4], was not found

[Channel %1: ] Block %2: Chai n element %3, referred to in $NK_NEXT[%4], was not found

[Channel %1: ] Block %2: Chain %3, referred to in $NK_NEXTP[%4], was not found

[Channel %1: ] Block %2: Maximum number of %3 chain elements exceeded

[Channel %1: ] Block %2: The maximum permissible value of fine offset in chain element %3 was exceeded

[Channel %1: ] Block %2: The axis direction in chain element %3 has not been defined.

[Channel %1: ] Block %2 : Invalid name in %3[%4]

[Channel %1: ] Block %2: The names of the protection areas $NP_PROT_NAME[%3] and $NP_ PROT_NAME[%4] are the same

[Channel %1: ] Block %2: The names of the protection area elements $NP_NAME[%3] and $NP_NAME[%4] are the same

[Channel %1: ] Block %2: Invalid pr otection area type in $NP_TYPE[%3]

[Channel %1: ] Block %2: CAD fi le not found: %3

[Channel %1: ] Block %2: The protection area element %3, referred to in $NP_1ST_PROT[%4], was not found

[Channel %1: ] Block %2: Protection area element %3, referred to in $NP_NEXT[%4], was not found

[Channel %1: ] Block %2: The protection zone or the CAD file %3 referred to in $TC_TP_PROTA[%4] was not found.

[Channel %1: ] Block %2: Maximum number of %3 protection area elements exceeded

[Channel %1: ] Block %2: The maximum permissible number of tool protection zone elements has been exceeded.

[Channel %1: ] Block %2: The protection area $NP_PROT_NAME[%3] does not contain any protection area elements

[Channel %1: ] Block %2: Protection area element %3, referred to in $NP_NEXT[%4], is already contained in the definition chain

[Channel %1: ] Block %2: Protection area %3, referred to in $NP_ADD[%4], was not found

[Channel %1: ] Block %2: The protection area indicated in $NP_ADD[%3] is linked with a kinematic chain

[Channel %1: ] Block %2: The tool protection zone %3 ($NP_PROT_NAME[%4]) contains a reference to a kinematic chain.

[Channel %1: ] Block %2: Name of the kinematic chain in $NP_CHAIN_NAME[%3] not defined

[Channel %1: ] Block %2: Protection area %3, referred to in $NP_ADD[%4], is already contai ned in the definition chain

[Channel %1: ] Block %2: Para meter $NP_PARA[%3,%4] is invalid

[Channel %1: ] Block %2: The contents (%4) of parameter $NP_BIT_NO[%3] are invalid

[Channel %1: ] Block %2: The names of the protection area groups $NP_NAME[%3] and $NP_NAME[%4] are the same

[Channel %1: ] Block %2: Element %4 of the protection area group %3 is not linked with a kinematic chain

[Channel %1: ] Block %2: The protection area referred to in element %4 of protection area group %3 was not found

[Channel %1: ] Block %2: The protection area group %3 referred to in $NP_ADD_GROUP[%4] was not found

[Channel %1: ] Block %2: Collision of the two protection areas %3 and %4

[Channel %1: ] The two protection zones %2 and %3 collide

[Channel %1: ] Not enough memory space during collision test of the two protection zones %2 and %3. Current ly available memory space: %4KB.

[Channel %1: ] Block %2: Not enough memory space for determining the distance between two protection zones. Currently available memory space: %3KB.

[Channel %1: ] Block %2: The protection area with the name %3 was not found.

[Channel %1: ] Block %2: The protection area with the name %3 was programmed several times.

[Channel %1: ] Block %2: Protection area %3 has not been assigned an interface bit

[Channel %1: ] Block %2: Invaid activation parameter during the PROTA function call

[Channel %1: ] Block %2: The contents (%3) of parameter $NP_INIT_STAT[%4] are invalid

[Channel %1: ] Block %2: Chain %3 referred to in $NP_CHAIN_NAME[%4] was not found

[Channel %1: ] Block %2: Chain element %3 referred to in $NP_CHAIN_ELEM[%4] was not found

[Channel %1: ] Block %2: The axis or frame name %3 contained in $NK_AXIS[%4] is unknown

[Channel %1: ] Axis %2 risk of collision %3 %4

[Channel %1: ] Axis %2 risk of collision %3 %4

[Channel %1: ] Block %2: Invalid definition of the protection zones or the kinematic chains.

[Channel %1: ] Block %2: The call of the function / procedure %3 is only permissible if the function 'C ollision monitoring' is present.

[Channel %1: ] Axis %2 risk of collision preactivated protection zones interface signal(s) %3

[Channel %1: ] Block %2: Maximum number of %4 protection zone facets exceeded in CAD file %3

[Channel %1: ] Block %2: Maximum number of %4 input points exceeded in CAD file %3

[Channel %1: ] Block %2: CAD file %3 is not a valid VRML file

[Channel %1: ] Block %2: CAD fi le %3 is not a valid STL file

Axis %1 is not safely referenced

Axis %1 error in a monitoring channel, code %2, values: NCK %3, drive %4

Axis %1 test stop is running

Checksum error found: %1 %2

Axis %1, difference safe input %2, NCK %3, drive %4

Axis %1 error in data cross check: static actual value difference

Axis %1 Test ext. pulse deletion running

Axis %1 acceptance test mode is active

Axis %1 SW limit switch deactivated

Axis %1 tolerance for safe standstill exceeded

Axis %1 safe velocity exceeded

Axis %1 safe end position exceeded

Axis %1 Safe monitoring for acceleration exceeded

Axis %1 stop E triggered

Axis %1 stop D triggered

Axis %1 stop C triggered

Axis %1 stop B triggered

Axis %1 stop A triggered

Axis %1 function not supported on this SIMODRIVE611D module

Axis %1 limit value for safe velocity %2 at gear ratio %3 too large (max. %4)

Axis %1 checksum error of safe monitoring. Confirmation and acceptance test required.

Axis %1 parameterizati on of MD %2[%3] invalid

Parameterization of MD %1[%2] invalid.

Axis %1 new hardware component, confirmation and functional test required.

Axis %1 encoder parameterization MD %2[%3] has been adjusted.

Axis %1 and %2 with the same PROFIsafe address %3.

Axis %1 value %2 in drive parameter %3 violates the limits of NCK MD %4.

Axis %1 parameterization MD %2[%3] changed, confirmation and functional test required.

Axis %1 waiti ng for motor module.

Axis %1 SI communication failure.

Axis %1 Drive assignment checksum error. Confirmation and acceptance test required!

Checksum error parameterization SPL and SPL interfaces. Confirmation and acceptance test required!

Checksum error safe PLC para meterization. Confirmation and acceptance test required!

Checksum error enable safe communication. Confirmation and acceptance test required!

Checksum error S7 PROFIsafe configuration. Confirmation and acceptance test required!

Error in data cross check NCK-PLC, %1[%2], NCK: %3; %4<ALSI>

Error in data cross check NCK-PLC, stop of %1

Communication broken off during NCK PLC data cross check, error detected by %1

Checksum error NCK-SPL, %1, %2, %3

Write access to system variable %1 only allowed from NCK-SPL

%1 SPL protection not activated

SPL start not allowed

SPL start not executed

SPL commissioning phase terminated

Double assignment in SPL assignment MD %1[%2] - MD %3[%4]

At least one axis is not safely referenced

Axis %1 difference in function safe operational stop, NCK: %2 drive: %3

Axis %1 difference in function safe velocity %2, NCK: %3 drive: %4

Axis %1 difference in function safe limit position %2, NCK: %3 drive: %4

Axis %1 difference in function safe cam plus %2, NCK: %3 drive: %4

Axis %1 difference in function safe cam minus %2, NCK: %3 drive: %4

Axis %1 difference in function safe velocity nx, NCK: %2 drive: %3

Axis %1 difference in function cam modulo monitoring, NCK: %2 drive: %3

Axis %1 fault during data transmission index%2.

Axis %1 fault during encoder evaluation of the safe actual value.

Axis %1 CRC error of the safe actual value.

Axis %1 hardware encoder error of the safe actual value.

Stop A triggered at least in 1 axis

Waiting for motor module of at least one axis.

PROFIsafe: cycle time %1 [ms] too long

PROFIsafe: MD %1[%2]: bus segment %3 error

PROFIsafe: MD %1[%2]: address %3 error

PROFIsafe: MD %1[%2]: SPL assignment error

PROFIsafe: double assignment MD %1[%2] - MD %3[%4]

PROFIsafe: number of signals in MD %1 [%2] <> MD %3[%4]

PROFIsafe: MD %1[%2] maximum number of F user data (%3 bits) exceeded.

PROFIsafe: MD %1[%2] max. sub slot number: %3 exceeded

PROFIsafe: MD %1[%2]: max. sub-slot address %3 exceeded.

PROFIsafe: Number of NCK F modules (%1) <> Number of S7 F modules (%2)

PROFIsafe: NCK F module MD %1[%2] unknown

PROFIsafe: S7 F module PROFIsafe address %1 unknown

PROFIsafe: NCK F module MD %1[%2] is not a %3 module

PROFIsafe: F module MD %1[%2] - MD %3[%4]: double assignment of PROFIsafe address

PROFIsafe: slave %1, configuration error %2

PROFIsafe: DP M not running up, DP info: %1

PROFIsafe: DP M version different, NCK: %1, PLC: %2

PROFIsafe: F module %1, %2 faulty

PROFIsafe: configur ation in DP M changed; error code %1 - %2

PROFIsafe: F module %1, %2 reports error %3

PROFIsafe: Slave %1, sign-of-life error

PROFIsafe: communication faul t F master component %1, error %2

PROFIsafe: F module %1, error on channel %2; %3<ALSI>

PROFIsafe: F module %1, general error

PROFIsafe: Current cycle time %1 [ms]> parameterized cycle time

PROFIsafe: %1 %2 re ports system error %3 (%4)

PROFIsafe: Diagnostics %1 %2 %3 %4

F_DP: Cycle time %1 [ms] is too long

F_DP: MD %1[%2]: SPL interface faulty

F_DP: Double assignment MD %1[%2] - MD %3[%4]

F_DP: Number of signals in MD %1 [%2] <> MD %3[%4]

F_DP: Parameter MD %1 [%2] <> MD %3[%4]

F_DP: Maximum number of active SPL connections (%1) exceeded for %2.