Siemens SINUMERIK 840D CNC 错误代码

System error in link module error code %1 error type %2

Link module generated an un specified error %1 NCU %2 %3 %4

No valid firmware

PLC sign-of-life monitoring

PLC has not started up

NCK battery warning threshold reached

NCK battery alarm

NCK battery alarm

NCK temperature alarm

NCK fan alarm type %1

5V/24V encoder or 15V D/A converter undervoltage

The actual service switch position forces the SRAM to be cleared at the next Power On (general reset active)

Hardware plug-in modu le for communication wi th the digitizer missing

No NCU link module exists, MD %1 reset

'Safety Integrated' is not available for link axis %1.

Link axis active and $MN_MM_SERVO_FIFO_SIZE != 3

[Channel %1: ] Axis %2 high-speed punching/nibbling not possible via link

Link axis active andMD18720 $MN_MM_SERVO_FIFO_SIZE != %1

[Channel %1: ] Fast punching/nibbling not possible in several channels

Reboot is delayed

Emergency stop

[Channel %1: ] Machine data %2[%3] has gap in axis assignment

[Channel %1: ] Axis %2 defined for more than one channel via machine data %3

[Channel %1: ] Machine data %2[%3] assigns an axis not defined in channel

Axis %1 incorrect assignment of master channel in machine data %2

[Channel %1: ] Machine data %2 axis %3 defined repeatedly as geometry axis

[Channel %1: ] Maximum number of axes in channel %1 exceeded. Limit %2

The maximum number of activatable axes has been exceeded (limit %1)

Axis %1 incorrect assignment of master NCU in machine data %2

Invalid identifier used in machine data %1[%2]

[Channel %1: ] Invalid identifier used in machine data %2[%3]

Invalid identifier used in machine data %1[%2]

Invalid NCU link config uration by machin e data %1 = %2 , on NCU_1 = %3

Axis %1 defined several times in %2

Axis %1 already used by NCU %2

Axis container %1, location %2 already used by NCU %3

Axis container %1, location %2 not used by any channel

Axis container %1 advance not allowed with current status of NCU %2

Identifier %1 used several times in machine data %2

[Channel %1: ] Identifier %2 used several times in machine data %3

[Channel %1: ] Axis %2: axis contai ner %3 switch not allowed: ext. work offset active

Axis container %1 switch not allowed, axis container %2 switch active

Invalid axis configuration due to missing axis container machine data

[Channel %1: ] Axis %2: axis container %3 switch not allowed: master/slave active.

Machine data %1[%2], link axis NC%3_AX%4 not used by any channel

NOTICE! MD %1 was also changed for the other axes of axis container %2

Attention! The axial MDs of the axes of the axis containers were matched.

NOTICE! The axial MDs in axis container %1 will be matched on the next power-up

[Channel %1: ] Identifier missing in machine date %2[%3]

[Channel %1: ] Link axis %2 defined for more than one channel in machine data %3

[Channel %1: ] Wrong identifier for facing axis in %2

NOTICE! NCU link communication still not connected

Local link axis %1 is not allowed for different interpolation cycle time = %2/%3

Interpolation cycle from NCU %1 = %2 does not match NCU%3 = %4

Wrong NCU link configuration by MD %1

[Channel %1: ] Axis identifier %2 not consistent with machine data %3

[Channel %1: ] Conflict between machine data %2 and machine data %3

NC code identifier %1 cannot be reconfigured to %2

Standard machine data loaded (%1, %2, %3, %4)

Backup data loaded

Buffered memory was restored from backup medium (potential loss of data!)

Normalizing machine data has been changed

Check the position of the encoder

Compile cycle functions define machine data number %1 several times

Machine data %1 (and maybe others) not changed due to missing permission level %2

%1 Machine data could not be changed with permission level %2

New value %1 of MD %2 not set. Requested %3 bytes too much %4 memory.

Incorrect configuration of indexing axis in MD %1

Too many errors during power-up

%1 error(s) during processing of MD initialization

System cycle time/scan time divider corrected for digital drive

IPO cycle changed to %1 ms

PLC cycle increased to %1 ms

Servo cycle changed to %1 ms

Sysclock cycle changed to %1 ms

Error in DP cycle of the SDB

Time ratio communication to Ipo changed to %1

[Channel %1: ] Invalid M function subprogram call configured

Illegal configuration of the 'Block display with absolute values' function

[Channel %1: ] Invalid M function number configured for spindle switchover

Invalid M function number for channel synchronisation assigned

Invalid M function number assigned to enable ASUP

[Channel %1: ] Invalid assignment of an M auxiliary function number

[Channel %1: ] Invalid M auxiliary function number in %2%3, MD reset

[Channel %1: ] M auxiliary function number %2 used several times (%3 and %4)

[Channel %1: ] Illegally predefined auxiliary function in %2%3, MD reset

[Channel %1: ] Illegal auxiliary function configured %2 %3 %4

[Channel %1: ] Geometry axis %2 must not be declared a rotary axis

[Channel %1: ] Spindle %2 declaration as rotary axis missing

[Channel %1: ] Spindle %2 declaration as modulo axis missing

[Channel %1: ] Spindle %2 declared repeatedly

[Channel %1: ] Axis %2 declaration as rotary axis missing

[Channel %1: ] Data alteration from external not possible in current channel state

Runtime overflow for IPO cycle or position controller cycle, IP %1

FastPlcCom functionality not available

PLCIO read error: %1

PLCIO write error: %1

Machine data %1 illegal

Machine data %1 assigns not activated NCK input/output byte %2

Machine data %1 and %2 both assign the same NCK output byte no. %3 several times

Assignment of NCK input/output byte via MD %1[%2] does not match hardware configuration

Hardware of external NCK outputs assigned repeatedly

Error on terminal block %1, error code %2

Sign of life monitoring: local P-bus not alive

Failure of module in local P-bus slot %1, error codes %2 %3 %4

Declaration in MD %1 is not allowed for axis %2.

Declaration in MD %1 index %2 is not allowed.

Axis %1 function %2 %3 and %4 not allowed

[Channel %1: ] The amount of fine correction in parameter %2 of the orientable toolholder %3 is too large

[Channel %1: ] Orientable toolholder no. %2 for orientation transformation %3 does not exist

[Channel %1: ] Invalid transformation type '%2' in toolholder %3 for orientation transformer %4

[Channel %1: ] Block %2 invalid transformation type in transformation no. %3

[Channel %1: ] Block %2 no data set available for transformation no. %3

[Channel %1: ] Invalid machine data for general 5-axis transformation error no. %2

[Channel %1: ] Attempt made to change the machine data of an active transformation.

[Channel %1: ] Block %2 Axis %3 defined in $NK_NAME[%4] is not available in the current channel

[Channel %1: ] Invalid configuration in chained transformation no. %2

[Channel %1: ] Invalid geoaxis assignment in machine data %2[%3]

[Channel %1: ] Invalid channel axis assignment in machine data %2[%3]

[Channel %1: ] Block %5 Configuration error %6 in transformation $NT_NAME[%3] = '%2'.

[Channel %1: ] No free memory space available for transformations.

[Channel %1: ] Axis identifier %2 machine data %3 not consistent with machine data %4

MD alteration will cause reorganiza tion of buffered memory (Art %1), (loss of data!) - %2

%1 causes a machine data reset

[Channel %1: ] Anachronism %2(%3) -> %4

[TO unit %1: ] H number %2 assigned more than once. H number linked again.

Invalid handwheel type for handwheel %1

Invalid handwheel module for handwheel %1

Invalid handwheel input for handwheel %1

Invalid handwheel module for handwheel %1

Invalid handwheel input for handwheel %1

Invalid handwheel module for handwheel %1

Invalid handwheel slot for handwheel %1

Logical PROFIBUS handwheel slot base address for handwheel %1 not found

Invalid handwheel module for handwheel %1

Invalid handwheel input for handwheel %1

PROFIBUS I/O: The logical slot / I/O area address %1 was not found.

PROFIBUS I/O: The logical slot / I/O area address %1 was not found.

Communication job not executable %1

Memory reorganized using standard machine data

[Channel %1: ] Data block %2 not or not completely created, error code %3

Machine data have been changed - now memory is reorganized

Limit of user memory has been adapted

Instead of %1 KB the system has only %2 KB of free user memory of type '%3'

Error while creating %1, error number %2 %3

Memory for CC MD full.

[Channel %1: ] Tool change not possible: Empty location for tool %2 on magazine %4 not available.

[Channel %1: ] Tool change not possi ble. Magazine no. %2 not available

[Channel %1: ] Tool change not possi ble. Magazine location number %2 on magazine %3 not available.

[Channel %1: ] Tool change not possi ble. Tool %2 not available or not usable

[Channel %1: ] Command %2 has invalid PLC acknowledge parameter %3 - identifier %4

[Channel %1: ] PLC acknowledg e for command %2 is missing

[Channel %1: ] Tool %2 cannot be placed in magazine %3 on location %4. Invalid definition of magazine!

[TO unit %1: ] Tool %2 has reached its prewarning limit with D = %4

[Channel %1: ] Tool %2 has reached its prewarning limit with D = %4

[TO unit %1: ] Tool %2 has reached its monitoring limit with D = %4

[Channel %1: ] Tool %2 has reached its monitoring limit with D = %4

[TO unit %1: ] Tool %2 with tool edge no. %3 has reached tool monitor warning limit

[Channel %1: ] Tool %2 with tool edge no. %3 has reached tool monitor warning limit

[TO unit %1: ] Tool %2 with tool edge no. %3 has reached tool monitoring limit

[Channel %1: ] Tool %2 with tool edge no. %3 has reached tool monitoring limit

[Channel %1: ] Tool move not possibl e. Empty location for tool %2 on magazine %4 not available.

[Channel %1: ] Tool move not possibl e. Magazine no. %2 not available.

[Channel %1: ] Tool move not possible. Location %2 on magazine %3 not available.

[Channel %1: ] Tool move not possible. Tool %2 not available/not usable.

[Channel %1: ] Tool %2 cannot be placed in magazine %3 on location %4. Invalid definition of magazine!

Workpiece counter: overflow in table of monitored cutting edges.

[Channel %1: ] Block %2 Function not allowed. Tool management/monitoring is not active.

Function not executable. No tool assigned to tool holder/spindle

[Channel %1: ] Block %2 %3 not available with tool management

[Channel %1: ] Block %2 NC command SETMTH not allowed because tool holder function not active

Writing of $P_USEKT not allowed.

[Channel %1: ] Function not executable. No tool assigned to desired magazine/magazine location %2.

[Channel %1: ] Block %2 tool change not possible. Invalid magazine location no. %3 in buffer magazine

[Channel %1: ] Block %2 tool cha nge not possible. No buffer magazine defined.

[Channel %1: ] Block %2 tool change not possible. Tool holder/spindle number = %3 not defined.

[Channel %1: ] Block %2 tool change not possible. No assignment between toolholder/spi ndle no. = %3 and buffer magazine location %4

[Channel %1: ] Block %2 tool change not possible. No distance relation available.

[Channel %1: ] Block %2 tool change not possible. Magazine location no. %3 not available in magazine %4

NC memory full

Too many part prog rams in the NC memory

The value of the machin e data %1%2 is too low

Too many files in directory

Too many director ies in the NC memory

Too many subdirectories

Data format not allowed

NC memory full

NC memory full

NC user memory full

NC machine OEM memory full

NC system memory full

NC memory limit TMP reached

NC external memory limit reached

File %1 lost

[Channel %1: ] Value of the machine data %2%3 is too low

Too many compile cycle alarms defined

MMC number range exceeded

Compile cycle alarm number has not been defined

Compile cycles VDI area: %1 byte for inputs and %2 byte for outputs. Maximum %3 bytes available.

Problem with externally linked compile cycle %1 %2