Zurück zu allen Siemens Modellen Search all database
Siemens SINUMERIK 840D CNC
Siemens SINUMERIK 840D CNC Fehlercodes
Vollständige Alarm- und Fehlercode-Referenz für die Siemens SINUMERIK 840D CNC. Durchsuchen Sie unten alle 4014 dokumentierten Fehlercodes, die jeweils zu einer detaillierten Anleitung zur Fehlerbehebung führen.
Search this section
Search Siemens SINUMERIK 840D CNC
Search all 4014 Siemens SINUMERIK 840D CNC codes without changing pages.
Vollständige Alarmliste (Page 16 of 21)
Code 202152
<location>OA: Insufficient memory
Lösung ansehen Code 203500
<location>TM: Initialization
Lösung ansehen Code 203501
<location>TM: Sampling time change
Lösung ansehen Code 203505
<location>TM: Analog input wire breakage
Lösung ansehen Code 203506
<location>24 V power supply missing
Lösung ansehen Code 203550
<location>TM: Speed setpoint filter natural frequency > Shannon frequency
Lösung ansehen Code 203590
<location>TM: Module not ready
Lösung ansehen Code 205000
<location>Power unit: Heat sink overtemperature
Lösung ansehen Code 205001
<location>Power unit: Chip overtemperature
Lösung ansehen Code 205002
<location>Power unit: Air intake overtemperature
Lösung ansehen Code 205003
<location>Power unit: Elec tronics board overtemperature
Lösung ansehen Code 205004
<location>Power unit: Rectifier overtemperature
Lösung ansehen Code 205005
<location>Cooling system: Cooling medium flow rate too low
Lösung ansehen Code 205006
<location>Power unit: Overtemperature thermal model
Lösung ansehen Code 205007
<location>Power unit: Overtemperature thermal model (chassis PU)
Lösung ansehen Code 205050
<location>Parallel circuit: Pulse enable in spite of pulse inhibit
Lösung ansehen Code 205051
<location>Parallel circuit: Power unit pulse enable missing
Lösung ansehen Code 205052
<location>Parallel circuit: Illegal current dissymmetry
Lösung ansehen Code 205053
<location>Parallel circuit: Inadmi ssible DC link vo ltage dissymmetry
Lösung ansehen Code 205054
<location>Parallel circ uit: Power unit de-activated
Lösung ansehen Code 205055
<location>Power circuit: Power units with different code numbers
Lösung ansehen Code 205056
<location>Parallel circuit: Power unit EPROM versions differ
Lösung ansehen Code 205057
<location>Parallel circuit: Power unit firmware versions differ
Lösung ansehen Code 205058
<location>Parallel circui t: VSM EEPROM versions differ
Lösung ansehen Code 205059
<location>Parallel circuit: VSM firmware versions differ
Lösung ansehen Code 205060
<location>Parallel circuit: Powe r unit firmware version does not match
Lösung ansehen Code 205061
<location>Infeed, number of VSM
Lösung ansehen Code 206000
<location>Infeed: Precharg ing monitoring time expired
Lösung ansehen Code 206010
<location>Infeed: Power unit EP 24 V missing in operation
Lösung ansehen Code 206050
<location>Infeed: Smart Mode not supported
Lösung ansehen Code 206052
<location>Infeed: Filter temperature evaluation not supported
Lösung ansehen Code 206100
<location>Infeed: Shutdown due to line supply undervoltage condition
Lösung ansehen Code 206105
<location>Infeed: Line supply undervoltage
Lösung ansehen Code 206200
<location>Infeed: Failure of one or several line phases
Lösung ansehen Code 206205
<location>Infeed: Voltage dip in at least one line supply phase
Lösung ansehen Code 206207
<location>Infeed: Line currents not symmetrical
Lösung ansehen Code 206210
<location>Infeed: Summation current too high
Lösung ansehen Code 206215
<location>Infeed: Summation current too high
Lösung ansehen Code 206250
<location>Infeed: Defective capacitor(s) in at least one phase of line filter
Lösung ansehen Code 206260
<location>Infeed: Temperature in the line filter too high
Lösung ansehen Code 206261
<location>Infeed: Temperature in the line filter permanently too high
Lösung ansehen Code 206262
<location>Infeed: Temperature switch in the line filter open when powering up
Lösung ansehen Code 206300
<location>Infeed: Line voltage too high at power on
Lösung ansehen Code 206301
<location>Infeed: Line supply overvoltage
Lösung ansehen Code 206310
<location>Infeed: Supply voltage (p0210) incorrectly parameterized
Lösung ansehen Code 206311
<location>Infeed: Supply voltage (p0210) incorrect
Lösung ansehen Code 206320
<location>Master/slave: 4-channel multiplexer control not valid
Lösung ansehen Code 206321
<location>Master/slave: 6-channel multiplexer control not valid
Lösung ansehen Code 206350
<location>Infeed: Measured line frequency too high
Lösung ansehen Code 206351
<location>Infeed: Measured line frequency too low
Lösung ansehen Code 206400
<location>Infeed: Line supply data identification selected/active
Lösung ansehen Code 206500
<location>Infeed: Line synchronization not possible
Lösung ansehen Code 206601
<location>Infeed: Current offset measurement interrupted
Lösung ansehen Code 206602
<location>Infeed: Current offset measurement not possible
Lösung ansehen Code 206700
<location>Infeed: Switch line contactor for load condition
Lösung ansehen Code 206800
<location>Infeed: Maximum steady-state DC link voltage reached
Lösung ansehen Code 206810
<location>Infeed: DC link voltage alarm threshold
Lösung ansehen Code 206900
<location>Braking Mo dule: Fault (1 -> 0)
Lösung ansehen Code 206901
<location>Braking Module: Pre-alarm I2t shutdown
Lösung ansehen Code 206904
<location>Braking Module internal is inhibited
Lösung ansehen Code 206905
<location>Braking Module internal I2t shutdown alarm
Lösung ansehen Code 206906
<location>Braking Module internal fault
Lösung ansehen Code 206907
<location>Braking Module internal overtemperature
Lösung ansehen Code 206908
<location>Braking Module internal shutdown due to overtemperature
Lösung ansehen Code 206909
<location>Braking Module internal Vce fault
Lösung ansehen Code 207011
<location>Drive: Motor overtemperature
Lösung ansehen Code 207012
<location>Drive: I2t motor model overtemperature
Lösung ansehen Code 207015
<location>Drive: Motor temperature sensor alarm
Lösung ansehen Code 207016
<location>Drive: Motor temperature sensor fault
Lösung ansehen Code 207080
<location>Drive: Incorrect control parameter
Lösung ansehen Code 207082
<location>Macro: Execution not possible
Lösung ansehen Code 207083
<location>Macro: ACX file not found
Lösung ansehen Code 207084
<location>Macro: Condition for WaitUntil not fulfilled
Lösung ansehen Code 207085
<location>Drive: Open-loop/closed-loop control parameters changed
Lösung ansehen Code 207086
<location>Units changeover: Parameter limit violation due to reference value change
Lösung ansehen Code 207087
<location>Drive: Encoderless oper ation not possible for the selected pulse frequency
Lösung ansehen Code 207088
<location>Units changeover: Parameter limit violation due to units changeover
Lösung ansehen Code 207089
<location>Changing over units: Adding a function module blocked if units changed over
Lösung ansehen Code 207090
<location>Drive: Upper torque limit less than the lower torque limit
Lösung ansehen Code 207100
<location>Drive: Sampling times cannot be reset
Lösung ansehen Code 207110
<location>Drive: Sampling time s and basic clock cycle do not match
Lösung ansehen Code 207200
<location>Drive: Master control ON/OFF1 command present
Lösung ansehen Code 207210
<location>Master control PC/AOP inhibited
Lösung ansehen Code 207220
<location>Drive: Master control by PLC missing
Lösung ansehen Code 207300
<location>Drive: Line contactor feedback signal missing
Lösung ansehen Code 207311
<location>Bypass motor switch
Lösung ansehen Code 207312
<location>Bypass LSS:
Lösung ansehen Code 207320
<location>Drive: Automatic restart interrupted
Lösung ansehen Code 207321
<location>Drive: Automatic restart active
Lösung ansehen Code 207329
<location>Drive: kT estimator, kT(iq) characteristic or voltage compensation does not function
Lösung ansehen Code 207330
<location>Flying restart: Measured search current too low
Lösung ansehen Code 207331
<location>FlyRestart: Not supported
Lösung ansehen Code 207350
<location>Drive: Measuring prob e parameterized to a digital output
Lösung ansehen Code 207400
<location>Drive: DC link voltage maximum controller active
Lösung ansehen Code 207401
<location>Drive: DC link voltage maximum controller de-activated
Lösung ansehen Code 207402
<location>Drive: DC link voltage minimum controller active
Lösung ansehen Code 207403
<location>Drive: Lower DC link voltage threshold reached
Lösung ansehen Code 207404
<location>Drive: Upper DC link voltage threshold reached
Lösung ansehen Code 207405
<location>Drive: Kinetic buffering minimum speed not reached
Lösung ansehen Code 207406
<location>Drive: Kinetic buf fering maximum time exceeded
Lösung ansehen Code 207409
<location>Drive: V/f control, current limiting controller active
Lösung ansehen Code 207410
<location>Drive: Current controller output limited
Lösung ansehen Code 207411
<location>Drive: Flux controller output limited
Lösung ansehen Code 207412
<location>Drive: Commutation angle incorrect (motor model)
Lösung ansehen Code 207413
<location>Drive: Commutation angle incorrect (pole position identification)
Lösung ansehen Code 207414
<location>Drive: Encoder serial number changed
Lösung ansehen Code 207415
<location>Drive: Angular commutation offset transfer running
Lösung ansehen Code 207416
<location>Drive: Flux controller configuration
Lösung ansehen Code 207420
<location>Drive: Current setpoint filter natural frequency > Shannon frequency
Lösung ansehen Code 207421
<location>Drive: Speed setpoint filter natural frequency > Shannon frequency
Lösung ansehen Code 207422
<location>Drive: Reference model natural frequency > Shannon frequency
Lösung ansehen Code 207423
<location>Drive: APC filter natural frequency > Shannon frequency
Lösung ansehen Code 207424
<location>Drive: Operating condition for APC not valid
Lösung ansehen Code 207425
<location>Drive: APC monitoring time for speed limit expired
Lösung ansehen Code 207429
<location>Drive: DSC without encoder not possible
Lösung ansehen Code 207430
<location>Drive: Changeover to ope n-loop torque controlled operation not possible
Lösung ansehen Code 207431
<location>Drive: Changeover to encoderless operation not possible
Lösung ansehen Code 207432
<location>Drive: Synchronous motor without overvoltage protection
Lösung ansehen Code 207433
<location>Drive: Closed-loop control with encoder is not possible as the encoder has not been unparked
Lösung ansehen Code 207434
<location>Drive: It is not possible to change the direction of rotation with the pulses enabled
Lösung ansehen Code 207435
<location>Drive: Setting the ramp-function generator for sensorless vector control
Lösung ansehen Code 207440
<location>EPOS: Jerk time is limited
Lösung ansehen Code 207441
<location>LR: Save the position offset of the absolute encoder adjustment
Lösung ansehen Code 207442
<location>LR: Multiturn does not match the modulo range
Lösung ansehen Code 207443
<location>LR: Reference point coordinate not in the permissible range
Lösung ansehen Code 207446
<location>Load gear: Position tracking cannot be reset
Lösung ansehen Code 207447
<location>Load gear: Position trac king, maximum actual value exceeded
Lösung ansehen Code 207448
<location>Load gear: Position trac king, linear axis has exceeded the maximum range
Lösung ansehen Code 207449
<location>Load gear: Position tracking, current position outside tolerance window
Lösung ansehen Code 207450
<location>LR: Standstill monitoring has responded
Lösung ansehen Code 207451
<location>LR: Position monitoring has responded
Lösung ansehen Code 207452
<location>LR: Following error too high
Lösung ansehen Code 207453
<location>LR: Position actu al value preprocessing error
Lösung ansehen Code 207454
<location>LR: Position actual value preprocessing does not have a valid encoder
Lösung ansehen Code 207455
<location>EPOS: Maximum velocity limited
Lösung ansehen Code 207456
<location>EPOS: Setpoint velocity limited
Lösung ansehen Code 207457
<location>EPOS: Combination of input signals illegal
Lösung ansehen Code 207458
<location>EPOS: Reference cam not found
Lösung ansehen Code 207459
<location>EPOS: No zero mark
Lösung ansehen Code 207460
<location>EPOS: End of reference cam not found
Lösung ansehen Code 207461
<location>EPOS: Reference point not set
Lösung ansehen Code 207462
<location>EPOS: Selected traversing block number does not exist
Lösung ansehen Code 207463
<location>EPOS: External block change not requested in the traversing block
Lösung ansehen Code 207464
<location>EPOS: Traversing block is inconsistent
Lösung ansehen Code 207465
<location>EPOS: Traversing block does not have a subsequent block
Lösung ansehen Code 207466
<location>EPOS: Traversing block number assigned a multiple number of times
Lösung ansehen Code 207467
<location>EPOS: Traversing block has illegal task parameters
Lösung ansehen Code 207468
<location>EPOS: Traversing block jump destination does not exist
Lösung ansehen Code 207469
<location>EPOS: Traversing block < target position < software limit switch minus
Lösung ansehen Code 207470
<location>EPOS: Traversing block> target position > software limit switch plus
Lösung ansehen Code 207471
<location>EPOS: Traversing block target position outside the modulo range
Lösung ansehen Code 207472
<location>EPOS: Traversing bl ock ABS_POS/ABS_NEG not possible
Lösung ansehen Code 207473
<location>EPOS: Beginning of traversing range reached
Lösung ansehen Code 207474
<location>EPOS: End of traversing range reached
Lösung ansehen Code 207475
<location>EPOS: Target position < start of traversing range
Lösung ansehen Code 207476
<location>EPOS: Target position > end of the traversing range
Lösung ansehen Code 207477
<location>EPOS: Target positio n < software limit switch minus
Lösung ansehen Code 207478
<location>EPOS: Target positio n > software limit switch plus
Lösung ansehen Code 207479
<location>EPOS: Software limit switch minus reached
Lösung ansehen Code 207480
<location>EPOS: Software limit switch plus reached
Lösung ansehen Code 207481
<location>EPOS: Axis positi on < software limit switch minus
Lösung ansehen Code 207482
<location>EPOS: Axis positi on > software limit switch plus
Lösung ansehen Code 207483
<location>EPOS: Travel to fixed stop clamping torque not reached
Lösung ansehen Code 207484
<location>EPOS: Fixed stop outside the monitoring window
Lösung ansehen Code 207485
<location>EPOS: Fixed stop not reached
Lösung ansehen Code 207486
<location>EPOS: Intermediate stop missing
Lösung ansehen Code 207487
<location>EPOS: Reject traversing task missing
Lösung ansehen Code 207488
<location>EPOS: Relative positioning not possible
Lösung ansehen Code 207489
<location>EPOS: Reference point correction outside the window
Lösung ansehen Code 207490
<location>EPOS: Enable signal withdrawn while traversing
Lösung ansehen Code 207491
<location>EPOS: STOP cam minus reached
Lösung ansehen Code 207492
<location>EPOS: STOP cam plus reached
Lösung ansehen Code 207493
<location>LR: Overflow of the value range for position actual value
Lösung ansehen Code 207494
<location>LR: Drive Data Set changeover in operation
Lösung ansehen Code 207495
<location>LR: Reference function interrupted
Lösung ansehen Code 207496
<location>EPOS: Enable not possible
Lösung ansehen Code 207497
<location>LR: Position setting value activated
Lösung ansehen Code 207498
<location>LR: Measuring pr obe evaluation not possible
Lösung ansehen Code 207499
<location>EPOS: Reversing cam approached with the incorrect traversing direction
Lösung ansehen Code 207500
<location>Drive: Power unit data set PDS not configured
Lösung ansehen Code 207501
<location>Drive: Motor Data Set MDS not configured
Lösung ansehen Code 207502
<location>Drive: Encoder Data Set EDS not configured
Lösung ansehen Code 207504
<location>Drive: Motor data set is not assigned to a drive data set
Lösung ansehen Code 207509
<location>Drive: Component number missing
Lösung ansehen Code 207510
<location>Drive: Identical encoder in the drive data set
Lösung ansehen Code 207511
<location>Drive: Encoder used a multiple number of times
Lösung ansehen Code 207512
<location>Drive: Encoder data set changeover cannot be parameterized
Lösung ansehen Code 207514
<location>Drive: Data structure does not correspond to the interface module
Lösung ansehen Code 207515
<location>Drive: Power unit and motor incorrectly connected
Lösung ansehen Code 207516
<location>Drive: Re-commission the data set
Lösung ansehen Code 207517
<location>Drive: Encoder data set changeover incorrectly parameterized
Lösung ansehen Code 207518
<location>Drive: Motor data set changeover incorrectly parameterized
Lösung ansehen Code 207519
<location>Drive: Motor changeover incorrectly parameterized
Lösung ansehen Code 207520
<location>Drive: Motor cannot be changed over
Lösung ansehen Code 207530
<location>Drive: Drive Data Set DDS not present
Lösung ansehen Code 207541
<location>Drive: Data set changeover not possible
Lösung ansehen Code 207550
<location>Drive: Not possible to reset encoder parameters
Lösung ansehen Code 207551
<location>Drive encoder: No commutation angle information
Lösung ansehen Code 207552
<location>Drive encoder: Encoder configuration not supported
Lösung ansehen Code 207553
<location>Drive encoder: Sensor Module configuration not supported
Lösung ansehen