Zurück zu allen Siemens Modellen Search all database
Siemens SINUMERIK 840D CNC
Siemens SINUMERIK 840D CNC Fehlercodes
Vollständige Alarm- und Fehlercode-Referenz für die Siemens SINUMERIK 840D CNC. Durchsuchen Sie unten alle 4014 dokumentierten Fehlercodes, die jeweils zu einer detaillierten Anleitung zur Fehlerbehebung führen.
Search this section
Search Siemens SINUMERIK 840D CNC
Search all 4014 Siemens SINUMERIK 840D CNC codes without changing pages.
Vollständige Alarmliste (Page 6 of 21)
Code 17833
[Channel %1: ] JOG a circle is active and JOG circles deactivated
Lösung ansehen Code 17900
[Channel %1: ] Block %2 axis %3 is no machine axis
Lösung ansehen Code 18000
[Channel %1: ] Block %2 NCK-specific protection zone %3 wrong. Error code %4
Lösung ansehen Code 18001
[Channel %1: ] Block %2 channel-specific protection zone %3 incorrect. Error code %4
Lösung ansehen Code 18002
[Channel %1: ] Block %2 NCK protection zone %3 cannot be activated. Error code %4
Lösung ansehen Code 18003
[Channel %1: ] Block %2 channel-specific protection zone %3 cannot be activated. Error code %4
Lösung ansehen Code 18004
[Channel %1: ] Block %2 orientation of workpiece-related protection zone %3 does not correspond to the orientation of tool-related protection zone %4
Lösung ansehen Code 18005
[Channel %1: ] Block %2 serious error in definition of NCK-specific protection zone %3
Lösung ansehen Code 18006
[Channel %1: ] Block %2 serious error in definition of channel-specific protection zone %3
Lösung ansehen Code 18100
[Channel %1: ] Block %2 invalid value assigned to FXS[]
Lösung ansehen Code 18101
[Channel %1: ] Block %2 invalid value assigned to FXST[]
Lösung ansehen Code 18102
[Channel %1: ] Block %2 invalid value assigned to FXSW[]
Lösung ansehen Code 18200
[Channel %1: ] Block %2 curve table: block search stop not allowed with definition CTABDEF
Lösung ansehen Code 18201
[Channel %1: ] Block %2 curve table: table %3 does not exist
Lösung ansehen Code 18202
[Channel %1: ] Block %2 curve table: instruction CTABEND without CTABDEF not allowed
Lösung ansehen Code 18203
[Channel %1: ] Block %2 curve table: instru ction CTABDEF not within CTABDEF
Lösung ansehen Code 18204
[Channel %1: ] Block %2 curve table: instruction SUPA not within CTABDEF
Lösung ansehen Code 18300
[Channel %1: ] Block %2 frame: fine shift not possible
Lösung ansehen Code 18310
[Channel %1: ] Block %2 frame: illegal rotation
Lösung ansehen Code 18311
[Channel %1: ] Block %2 frame: illegal instruction
Lösung ansehen Code 18312
[Channel %1: ] Block %2 frame: fine shift not configured
Lösung ansehen Code 18313
[Channel %1: ] Block %2 frame: illegal switch over of geometry axes
Lösung ansehen Code 18314
[Channel %1: ] Block %2 frame: type conflict
Lösung ansehen Code 18400
[Channel %1: ] Block %2 language change not possible:%3
Lösung ansehen Code 20000
[Channel %1: ] Axis %2 reference cam not reached
Lösung ansehen Code 20001
[Channel %1: ] Axis %2 no cam signal present
Lösung ansehen Code 20002
[Channel %1: ] Axis %2 zero mark not found
Lösung ansehen Code 20003
[Channel %1: ] Axis %2 measuring system error
Lösung ansehen Code 20004
[Channel %1: ] Axis %2 reference mark missing
Lösung ansehen Code 20005
[Channel %1: ] Axis %2 reference point approach aborted
Lösung ansehen Code 20006
[Channel %1: ] Axis %2 reference point creep velocity not reached
Lösung ansehen Code 20007
[Channel %1: ] Axis %2 reference point approach requires 2 measuring systems
Lösung ansehen Code 20008
[Channel %1: ] Axis %2 reference point approach requires second referenced measuring system
Lösung ansehen Code 20050
[Channel %1: ] Axis %2 handwheel mode active
Lösung ansehen Code 20051
[Channel %1: ] Axis %2 handwheel mode not possible
Lösung ansehen Code 20052
[Channel %1: ] Axis %2 already active
Lösung ansehen Code 20053
[Channel %1: ] Axis %2 DRF, FTOCO N, external zero point offset not possible
Lösung ansehen Code 20054
[Channel %1: ] Axis %2 wrong index for indexing axis in JOG mode
Lösung ansehen Code 20055
[Channel %1: ] Master spindle not present in JOG mode
Lösung ansehen Code 20056
[Channel %1: ] Axis %2 no revoluti onal feedrate possible. Axis/spindle %3 stationary
Lösung ansehen Code 20057
[Channel %1: ] Block %2 revolutional feedrate for axis/spindle %3 is <= zero
Lösung ansehen Code 20058
[Channel %1: ] Axis %2 revolutional feedrate: illegal feed source
Lösung ansehen Code 20059
[Channel %1: ] Axis %2 already active due to %3
Lösung ansehen Code 20060
[Channel %1: ] Axis %2 cannot be traversed as geometry axis
Lösung ansehen Code 20061
[Channel %1: ] Axis %2 cannot be traversed as orientation axis
Lösung ansehen Code 20062
[Channel %1: ] Axis %2 already active
Lösung ansehen Code 20063
[Channel %1: ] Axis %2 orientation axes cannot be traversed without transformation
Lösung ansehen Code 20064
[Channel %1: ] Axis %2 selection of several axes with an active taper angle is not permitted.
Lösung ansehen Code 20065
[Channel %1: ] Master spindle not defined for geometry axes in JOG mode
Lösung ansehen Code 20070
[Channel %1: ] Axis %2 software limit switch %3
Lösung ansehen Code 20071
[Channel %1: ] Axis %2 working area limit %3
Lösung ansehen Code 20072
[Channel %1: ] Axis %2 is not an indexing axis
Lösung ansehen Code 20073
[Channel %1: ] Axis %2 cannot be repositioned
Lösung ansehen Code 20074
[Channel %1: ] Axis %2 wrong index position
Lösung ansehen Code 20075
[Channel %1: ] Axis %2 can currently not oscillate
Lösung ansehen Code 20076
[Channel %1: ] Axis %2 oscillating - mode change not possible
Lösung ansehen Code 20077
[Channel %1: ] Axis %2 programmed position is behind software limit switch %3
Lösung ansehen Code 20078
[Channel %1: ] Axis %2 programmed position is behind working area limit %3
Lösung ansehen Code 20079
[Channel %1: ] Axis %2 oscillation path %3 <= 0
Lösung ansehen Code 20080
[Channel %1: ] Axis %2 no handwheel assigned for override
Lösung ansehen Code 20081
[Channel %1: ] Axis %2 braking position cannot be accepted as a new reversing position
Lösung ansehen Code 20082
[Channel %1: ] Axis %2 coordinate system-specific working area limit %3
Lösung ansehen Code 20083
[Channel %1: ] Axis %2 programmed position lies behind the coordinate system-specific working area limit %3
Lösung ansehen Code 20085
[Channel %1: ] Contour handwheel: traverse direction or overtravel of beginning of block not allowed
Lösung ansehen Code 20090
Axis %1 travel to fixed stop not possible. Check programming and axis data.
Lösung ansehen Code 20091
Axis %1 has not reached fixed stop
Lösung ansehen Code 20092
Axis %1 travel to fixed stop still active
Lösung ansehen Code 20093
Axis %1 standstill monitoring at fi xed-stop end point has been triggered
Lösung ansehen Code 20094
Axis %1 function has been aborted
Lösung ansehen Code 20095
Axis %1 illegal to rque, current torque %2
Lösung ansehen Code 20096
Axis %1 brake test aborted, additional information %2
Lösung ansehen Code 20097
Axis %1 incorrect travel direction brake test
Lösung ansehen Code 20100
[Channel %1: ] :Invalid configuration for digitizing
Lösung ansehen Code 20101
Timeout during initia lization of communication with the digitizer
Lösung ansehen Code 20102
[Channel %1: ] No or invalid trafo at digitizing active
Lösung ansehen Code 20103
[Channel %1: ] Digitizing module does not support 3+2 axes digitizing
Lösung ansehen Code 20105
[Channel %1: ] Axes stopped by digitizer. Error code: %2
Lösung ansehen Code 20106
The digitizer has triggered an emergency stop.
Lösung ansehen Code 20108
Invalid data package received from the digitizer. Error codes %1, %2
Lösung ansehen Code 20109
Error in communication with the digitize r: status code of com-circuit: %1
Lösung ansehen Code 20120
Axis %1: too many compensation relations
Lösung ansehen Code 20121
Axis %1: Configuration error in compensation table %2
Lösung ansehen Code 20122
Compensation table %1: invalid axis assignment
Lösung ansehen Code 20123
Axis %1: different output assignment of multiplied tables
Lösung ansehen Code 20124
Axis %1: sum of compensation values too large
Lösung ansehen Code 20125
Axis %1: change of compensation value is too rapid
Lösung ansehen Code 20130
[Channel %1: ] Contour tunnel monitoring
Lösung ansehen Code 20139
[Channel %1: ] Block %2 motion-synchronous action: invalid marker
Lösung ansehen Code 20140
[Channel %1: ] Motion synchronous action: traversing of command axis %2 see NC alarm %3
Lösung ansehen Code 20141
[Channel %1: ] Motion synchronous action: illegal axis type
Lösung ansehen Code 20142
[Channel %1: ] Command axis %2: rotation of axis container already enabled
Lösung ansehen Code 20143
[Channel %1: ] Axis %2 command axis cannot be started as it is controlled by the PLC
Lösung ansehen Code 20144
[Channel %1: ] Block %2 motion synchronous action: system variable access not possible
Lösung ansehen Code 20145
[Channel %1: ] Block %2 motion synchronous action: arithmetic error
Lösung ansehen Code 20146
[Channel %1: ] Block %2 motion synchronous action: nesting depth exceeded
Lösung ansehen Code 20147
[Channel %1: ] Block %2 motion synchronous action: command not executable
Lösung ansehen Code 20148
[Channel %1: ] Block %2 motion synchronous action: internal error %3
Lösung ansehen Code 20149
[Channel %1: ] Block %2 motion synchronous action: illegal index
Lösung ansehen Code 20150
[Channel %1: ] Tool management: PLC terminates interrupted command
Lösung ansehen Code 20160
[Channel %1: ] Tool management: PLC can terminate only incorrectly aborted commands
Lösung ansehen Code 20170
[Channel %1: ] Machine data $AC_FIFO invalid
Lösung ansehen Code 20200
[Channel %1: ] Invalid spindle number %2 with tool fine compensation
Lösung ansehen Code 20201
[Channel %1: ] Spindle %2 no tool assigned
Lösung ansehen Code 20203
[Channel %1: ] No active tool
Lösung ansehen Code 20204
[Channel %1: ] PUTFTOC command not allowed with FTOCOF
Lösung ansehen Code 20210
[Channel %1: ] Block %3 spindle %2 wrong values for centerless grinding
Lösung ansehen Code 20211
[Channel %1: ] Block %3 spindle %2 support point beyond range limits
Lösung ansehen Code 20300
[Channel %1: ] Axis %2 orientation not possible
Lösung ansehen Code 21550
[Channel %1: ] Axis %2 Travel from hardware limit sw itch not possible. Reason: %3
Lösung ansehen Code 21610
[Channel %1: ] Axis %2 encoder %3 frequency exceeded
Lösung ansehen Code 21612
[Channel %1: ] Axis %2: enable reset, cause %3
Lösung ansehen Code 21613
Axis %1 measuring system changing
Lösung ansehen Code 21614
[Channel %1: ] Axis %2 hardware limit switch %3
Lösung ansehen Code 21615
[Channel %1: ] Axis %2 taken from traverse mode to follow-up mode
Lösung ansehen Code 21616
[Channel %1: ] Block %2 overlaid motion active at transformation switchover
Lösung ansehen Code 21617
[Channel %1: ] Block %2 transformation does not allow to traverse the pole
Lösung ansehen Code 21618
[Channel %1: ] As from block %2 transformation active: overlaid motion too great
Lösung ansehen Code 21619
[Channel %1: ] Block %2 transformation active: motion not possible
Lösung ansehen Code 21620
[Channel %1: ] Axis %2 Emergency braking ramp activated
Lösung ansehen Code 21650
[Channel %1: ] Axis %2 overlaid motion not allowed
Lösung ansehen Code 21660
[Channel %1: ] Block %2 axis %3 conflict between SYNACT: $AA_OFF and CORROF
Lösung ansehen Code 21665
[Channel %1: ] $AA_TOFF cleared
Lösung ansehen Code 21670
[Channel %1: ] Block %2 illegal change of tool direction with $AA_TOFF active
Lösung ansehen Code 21700
[Channel %1: ] Block %3 axis %2 touch probe already deflected, edge polarity not possible
Lösung ansehen Code 21701
[Channel %1: ] Block %3 axis %2 measurement not possible
Lösung ansehen Code 21702
[Channel %1: ] Block %3 axis %2 measurement aborted
Lösung ansehen Code 21703
[Channel %1: ] Block %3 axis %2 touch probe not deflected, illegal edge polarity
Lösung ansehen Code 21740
Output value at analog output no. %1 has been limited
Lösung ansehen Code 21750
Error during output of cam switching signals via timer
Lösung ansehen Code 21760
[Channel %1: ] Block %2 too many auxiliary functions programmed
Lösung ansehen Code 21800
[Channel %1: ] Workpiece setpoint %2 reached
Lösung ansehen Code 22000
[Channel %1: ] Block %3 spindle %2 gear stage change not possible
Lösung ansehen Code 22005
[Channel %1: ] Spindle %2 selected gear stage %3 not installed
Lösung ansehen Code 22010
[Channel %1: ] Block %3 spindle %2 actual gear stage differs from requested gear stage
Lösung ansehen Code 22011
[Channel %1: ] Block %3 spindle %2 change to programmed gear stage not possible
Lösung ansehen Code 22012
[Channel %1: ] Block %2 leading spindle %3 is in simulation.
Lösung ansehen Code 22013
[Channel %1: ] Block %2 dependent spindle %3 is in simulation.
Lösung ansehen Code 22014
[Channel %1: ] Block %2. The dynamics of leading spindle %3 and dependent spindle %4 is too variably
Lösung ansehen Code 22015
[Channel %1: ] Block %2 following spindle %3 No dynamic response for supplementary motion
Lösung ansehen Code 22016
[Channel %1: ] Block %2 following spindle %3 in the range of reduced acceleration capability
Lösung ansehen Code 22018
[Channel %1: ] Block %2 following axis/spindle %3 time monitoring: 'Synchronism fine' not reached
Lösung ansehen Code 22019
[Channel %1: ] Block %2 following axis/spindle %3 time monitoring: 'Synchronism coarse' not reached
Lösung ansehen Code 22020
[Channel %1: ] Block %3 spindle %2 gear step change position not reached
Lösung ansehen Code 22022
[Channel %1: ] Block %2 spindle %3 gear stage %4 is expected for axis mode.
Lösung ansehen Code 22030
[Channel %1: ] Block %2 foll owing spindle %3 Impermissible programming
Lösung ansehen Code 22033
[Channel %1: ] Block %2 Axis/spindle %3 'Correct synchronism' diagnostics %4
Lösung ansehen Code 22034
[Channel %1: ] Block %2 followin g spindle %3 PLC signal 'Enable override' has been set.
Lösung ansehen Code 22035
[Channel %1: ] Block %2 following axis/spindle %3 unable to determine the offset value (reason %4).
Lösung ansehen Code 22036
[Channel %1: ] Block %2 Axis/spindle %3 Synchronism override not possible (reason %4)
Lösung ansehen Code 22037
[Channel %1: ] Block %2 Axis/spindle %3 'Correct synchronism' is being ignored
Lösung ansehen Code 22038
[Channel %1: ] Block %2 Axis/Spindle %3 'Delete synchronism override' is being ignored
Lösung ansehen Code 22040
[Channel %1: ] Block %3 spindle %2 is not referenced with zero marker
Lösung ansehen Code 22045
Block %2 spindle/axis %3 not available in channel %1 because active in channel %4
Lösung ansehen Code 22050
[Channel %1: ] Block %3 spindle %2 no transition from speed control mode to position control mode
Lösung ansehen Code 22051
[Channel %1: ] Block %3 spindle %2 reference mark not found
Lösung ansehen Code 22052
[Channel %1: ] Block %3 spindle %2 no standstill on block change
Lösung ansehen Code 22053
[Channel %1: ] Block %3 spindle %2 reference mode not supported
Lösung ansehen Code 22054
[Channel %1: ] Block %3 spindle %2 improper punching signal
Lösung ansehen Code 22055
[Channel %1: ] Block %3 spindle %2 configured positioning speed is too high
Lösung ansehen Code 22057
[Channel %1: ] Block %2 for following spindle %3 coupling as leading spindle/axis already existing
Lösung ansehen Code 22058
[Channel %1: ] Block %2 for leading spindle %3 coupling as following spindle/axis already existing
Lösung ansehen Code 22060
[Channel %1: ] Position control expected for axis/spindle %2
Lösung ansehen Code 22062
[Channel %1: ] Axis %2 reference point approach: zero marker search velocity (MD) is not reached
Lösung ansehen Code 22064
[Channel %1: ] Axis %2 reference point approach: zero marker search velocity (MD) is too high
Lösung ansehen Code 22065
[Channel %1: ] Tool management: Tool motion is not possible as tool %2 is not in magazine %4.
Lösung ansehen Code 22066
[Channel %1: ] Tool management: Tool change is not possible as tool %2 is not in magazine %4.
Lösung ansehen Code 22067
[Channel %1: ] Tool management: tool change not possible since there is no tool available in tool group %2
Lösung ansehen Code 22068
[Channel %1: ] Block %2 tool management: no tool available in tool group %3
Lösung ansehen Code 22069
[Channel %1: ] Block %2 tool management: No tool available in tool group %3, program %4
Lösung ansehen Code 22070
[TO unit %1: ] Please change tool %2 into magazine. Repeat data backup
Lösung ansehen Code 22071
[TO unit %1: ] Tool %2 is active, but not in the magazine area under consideration
Lösung ansehen Code 22100
[Channel %1: ] Block %3 spindle %2 chuck speed exceeded
Lösung ansehen Code 22101
[Channel %1: ] Block %3 spindle %2 maximum speed for encoder resynchronization exceeded
Lösung ansehen Code 22150
[Channel %1: ] Block %3 spindle %2 maximum speed for position control exceeded
Lösung ansehen Code 22200
[Channel %1: ] Spindle %2 axis stopped during tapping
Lösung ansehen Code 22250
[Channel %1: ] Spindle %2 axis stopped during thread cutting
Lösung ansehen Code 22260
[Channel %1: ] Spindle %2 thread might be damaged
Lösung ansehen Code 22270
[Channel %1: ] Block %2 maximum tapping speed reached
Lösung ansehen Code 22275
[Channel %1: ] Block %2 zero velocity of thread axis at position %3 reached
Lösung ansehen Code 22280
[Channel %1: ] In block %2: Prog. acceleration path too short %3, %4 required
Lösung ansehen Code 22290
[Channel %1: ] Spindle operation for transformed spindle/axis %2 not possible (reason: error code %3).
Lösung ansehen Code 22295
Channel %1 Spindle %2 DBB30 function not possible (cause: error code %3)
Lösung ansehen Code 22296
Channel %1 Spindle %2 Error on gear stage change (cause: error code %3)
Lösung ansehen Code 22297
Channel %1 Spindle %2 FC18 function not possible (cause: error code %3)
Lösung ansehen Code 22320
[Channel %1: ] Block %2 PUTFTOCF command could not be transferred
Lösung ansehen Code 22321
[Channel %1: ] Axis %2 PRESET not allowed during traverse motion
Lösung ansehen Code 22322
[Channel %1: ] Axis %2 PRESET: illegal value
Lösung ansehen Code 22400
[Channel %1: ] Option 'contour handwheel' not set
Lösung ansehen Code 25000
Axis %1 hardware fault of active encoder
Lösung ansehen Code 25001
Axis %1 hardware fault of passive encoder
Lösung ansehen Code 25010
Axis %1 pollution of measuring system
Lösung ansehen Code 25011
Axis %1 pollution of passive encoder
Lösung ansehen Code 25020
Axis %1 zero mark monitoring of active encoder
Lösung ansehen Code 25021
Axis %1 zero mark moni toring of passive encoder
Lösung ansehen Code 25022
Axis %1 encoder %2 warning %3
Lösung ansehen Code 25030
Axis %1 actual velocity alarm limit
Lösung ansehen Code 25031
Axis %1 actual velocity warning limit
Lösung ansehen Code 25040
Axis %1 standstill monitoring
Lösung ansehen Code 25042
Axis %1 standstill monitori ng during torque/force limitation
Lösung ansehen Code 25050
Axis %1 contour monitoring
Lösung ansehen