Volver a todos los modelos de Siemens Search all database
Siemens SINUMERIK 840D CNC
Códigos de error de Siemens SINUMERIK 840D CNC
Referencia completa de códigos de alarma y error para Siemens SINUMERIK 840D CNC. Explore a continuación los 4014 códigos de falla documentados, cada uno con un enlace a una guía detallada de solución de problemas.
Search this section
Search Siemens SINUMERIK 840D CNC
Search all 4014 Siemens SINUMERIK 840D CNC codes without changing pages.
Lista completa de alarmas (Page 6 of 21)
Código 17833
[Channel %1: ] JOG a circle is active and JOG circles deactivated
Ver solución Código 17900
[Channel %1: ] Block %2 axis %3 is no machine axis
Ver solución Código 18000
[Channel %1: ] Block %2 NCK-specific protection zone %3 wrong. Error code %4
Ver solución Código 18001
[Channel %1: ] Block %2 channel-specific protection zone %3 incorrect. Error code %4
Ver solución Código 18002
[Channel %1: ] Block %2 NCK protection zone %3 cannot be activated. Error code %4
Ver solución Código 18003
[Channel %1: ] Block %2 channel-specific protection zone %3 cannot be activated. Error code %4
Ver solución Código 18004
[Channel %1: ] Block %2 orientation of workpiece-related protection zone %3 does not correspond to the orientation of tool-related protection zone %4
Ver solución Código 18005
[Channel %1: ] Block %2 serious error in definition of NCK-specific protection zone %3
Ver solución Código 18006
[Channel %1: ] Block %2 serious error in definition of channel-specific protection zone %3
Ver solución Código 18100
[Channel %1: ] Block %2 invalid value assigned to FXS[]
Ver solución Código 18101
[Channel %1: ] Block %2 invalid value assigned to FXST[]
Ver solución Código 18102
[Channel %1: ] Block %2 invalid value assigned to FXSW[]
Ver solución Código 18200
[Channel %1: ] Block %2 curve table: block search stop not allowed with definition CTABDEF
Ver solución Código 18201
[Channel %1: ] Block %2 curve table: table %3 does not exist
Ver solución Código 18202
[Channel %1: ] Block %2 curve table: instruction CTABEND without CTABDEF not allowed
Ver solución Código 18203
[Channel %1: ] Block %2 curve table: instru ction CTABDEF not within CTABDEF
Ver solución Código 18204
[Channel %1: ] Block %2 curve table: instruction SUPA not within CTABDEF
Ver solución Código 18300
[Channel %1: ] Block %2 frame: fine shift not possible
Ver solución Código 18310
[Channel %1: ] Block %2 frame: illegal rotation
Ver solución Código 18311
[Channel %1: ] Block %2 frame: illegal instruction
Ver solución Código 18312
[Channel %1: ] Block %2 frame: fine shift not configured
Ver solución Código 18313
[Channel %1: ] Block %2 frame: illegal switch over of geometry axes
Ver solución Código 18314
[Channel %1: ] Block %2 frame: type conflict
Ver solución Código 18400
[Channel %1: ] Block %2 language change not possible:%3
Ver solución Código 20000
[Channel %1: ] Axis %2 reference cam not reached
Ver solución Código 20001
[Channel %1: ] Axis %2 no cam signal present
Ver solución Código 20002
[Channel %1: ] Axis %2 zero mark not found
Ver solución Código 20003
[Channel %1: ] Axis %2 measuring system error
Ver solución Código 20004
[Channel %1: ] Axis %2 reference mark missing
Ver solución Código 20005
[Channel %1: ] Axis %2 reference point approach aborted
Ver solución Código 20006
[Channel %1: ] Axis %2 reference point creep velocity not reached
Ver solución Código 20007
[Channel %1: ] Axis %2 reference point approach requires 2 measuring systems
Ver solución Código 20008
[Channel %1: ] Axis %2 reference point approach requires second referenced measuring system
Ver solución Código 20050
[Channel %1: ] Axis %2 handwheel mode active
Ver solución Código 20051
[Channel %1: ] Axis %2 handwheel mode not possible
Ver solución Código 20052
[Channel %1: ] Axis %2 already active
Ver solución Código 20053
[Channel %1: ] Axis %2 DRF, FTOCO N, external zero point offset not possible
Ver solución Código 20054
[Channel %1: ] Axis %2 wrong index for indexing axis in JOG mode
Ver solución Código 20055
[Channel %1: ] Master spindle not present in JOG mode
Ver solución Código 20056
[Channel %1: ] Axis %2 no revoluti onal feedrate possible. Axis/spindle %3 stationary
Ver solución Código 20057
[Channel %1: ] Block %2 revolutional feedrate for axis/spindle %3 is <= zero
Ver solución Código 20058
[Channel %1: ] Axis %2 revolutional feedrate: illegal feed source
Ver solución Código 20059
[Channel %1: ] Axis %2 already active due to %3
Ver solución Código 20060
[Channel %1: ] Axis %2 cannot be traversed as geometry axis
Ver solución Código 20061
[Channel %1: ] Axis %2 cannot be traversed as orientation axis
Ver solución Código 20062
[Channel %1: ] Axis %2 already active
Ver solución Código 20063
[Channel %1: ] Axis %2 orientation axes cannot be traversed without transformation
Ver solución Código 20064
[Channel %1: ] Axis %2 selection of several axes with an active taper angle is not permitted.
Ver solución Código 20065
[Channel %1: ] Master spindle not defined for geometry axes in JOG mode
Ver solución Código 20070
[Channel %1: ] Axis %2 software limit switch %3
Ver solución Código 20071
[Channel %1: ] Axis %2 working area limit %3
Ver solución Código 20072
[Channel %1: ] Axis %2 is not an indexing axis
Ver solución Código 20073
[Channel %1: ] Axis %2 cannot be repositioned
Ver solución Código 20074
[Channel %1: ] Axis %2 wrong index position
Ver solución Código 20075
[Channel %1: ] Axis %2 can currently not oscillate
Ver solución Código 20076
[Channel %1: ] Axis %2 oscillating - mode change not possible
Ver solución Código 20077
[Channel %1: ] Axis %2 programmed position is behind software limit switch %3
Ver solución Código 20078
[Channel %1: ] Axis %2 programmed position is behind working area limit %3
Ver solución Código 20079
[Channel %1: ] Axis %2 oscillation path %3 <= 0
Ver solución Código 20080
[Channel %1: ] Axis %2 no handwheel assigned for override
Ver solución Código 20081
[Channel %1: ] Axis %2 braking position cannot be accepted as a new reversing position
Ver solución Código 20082
[Channel %1: ] Axis %2 coordinate system-specific working area limit %3
Ver solución Código 20083
[Channel %1: ] Axis %2 programmed position lies behind the coordinate system-specific working area limit %3
Ver solución Código 20085
[Channel %1: ] Contour handwheel: traverse direction or overtravel of beginning of block not allowed
Ver solución Código 20090
Axis %1 travel to fixed stop not possible. Check programming and axis data.
Ver solución Código 20091
Axis %1 has not reached fixed stop
Ver solución Código 20092
Axis %1 travel to fixed stop still active
Ver solución Código 20093
Axis %1 standstill monitoring at fi xed-stop end point has been triggered
Ver solución Código 20094
Axis %1 function has been aborted
Ver solución Código 20095
Axis %1 illegal to rque, current torque %2
Ver solución Código 20096
Axis %1 brake test aborted, additional information %2
Ver solución Código 20097
Axis %1 incorrect travel direction brake test
Ver solución Código 20100
[Channel %1: ] :Invalid configuration for digitizing
Ver solución Código 20101
Timeout during initia lization of communication with the digitizer
Ver solución Código 20102
[Channel %1: ] No or invalid trafo at digitizing active
Ver solución Código 20103
[Channel %1: ] Digitizing module does not support 3+2 axes digitizing
Ver solución Código 20105
[Channel %1: ] Axes stopped by digitizer. Error code: %2
Ver solución Código 20106
The digitizer has triggered an emergency stop.
Ver solución Código 20108
Invalid data package received from the digitizer. Error codes %1, %2
Ver solución Código 20109
Error in communication with the digitize r: status code of com-circuit: %1
Ver solución Código 20120
Axis %1: too many compensation relations
Ver solución Código 20121
Axis %1: Configuration error in compensation table %2
Ver solución Código 20122
Compensation table %1: invalid axis assignment
Ver solución Código 20123
Axis %1: different output assignment of multiplied tables
Ver solución Código 20124
Axis %1: sum of compensation values too large
Ver solución Código 20125
Axis %1: change of compensation value is too rapid
Ver solución Código 20130
[Channel %1: ] Contour tunnel monitoring
Ver solución Código 20139
[Channel %1: ] Block %2 motion-synchronous action: invalid marker
Ver solución Código 20140
[Channel %1: ] Motion synchronous action: traversing of command axis %2 see NC alarm %3
Ver solución Código 20141
[Channel %1: ] Motion synchronous action: illegal axis type
Ver solución Código 20142
[Channel %1: ] Command axis %2: rotation of axis container already enabled
Ver solución Código 20143
[Channel %1: ] Axis %2 command axis cannot be started as it is controlled by the PLC
Ver solución Código 20144
[Channel %1: ] Block %2 motion synchronous action: system variable access not possible
Ver solución Código 20145
[Channel %1: ] Block %2 motion synchronous action: arithmetic error
Ver solución Código 20146
[Channel %1: ] Block %2 motion synchronous action: nesting depth exceeded
Ver solución Código 20147
[Channel %1: ] Block %2 motion synchronous action: command not executable
Ver solución Código 20148
[Channel %1: ] Block %2 motion synchronous action: internal error %3
Ver solución Código 20149
[Channel %1: ] Block %2 motion synchronous action: illegal index
Ver solución Código 20150
[Channel %1: ] Tool management: PLC terminates interrupted command
Ver solución Código 20160
[Channel %1: ] Tool management: PLC can terminate only incorrectly aborted commands
Ver solución Código 20170
[Channel %1: ] Machine data $AC_FIFO invalid
Ver solución Código 20200
[Channel %1: ] Invalid spindle number %2 with tool fine compensation
Ver solución Código 20201
[Channel %1: ] Spindle %2 no tool assigned
Ver solución Código 20203
[Channel %1: ] No active tool
Ver solución Código 20204
[Channel %1: ] PUTFTOC command not allowed with FTOCOF
Ver solución Código 20210
[Channel %1: ] Block %3 spindle %2 wrong values for centerless grinding
Ver solución Código 20211
[Channel %1: ] Block %3 spindle %2 support point beyond range limits
Ver solución Código 20300
[Channel %1: ] Axis %2 orientation not possible
Ver solución Código 21550
[Channel %1: ] Axis %2 Travel from hardware limit sw itch not possible. Reason: %3
Ver solución Código 21610
[Channel %1: ] Axis %2 encoder %3 frequency exceeded
Ver solución Código 21612
[Channel %1: ] Axis %2: enable reset, cause %3
Ver solución Código 21613
Axis %1 measuring system changing
Ver solución Código 21614
[Channel %1: ] Axis %2 hardware limit switch %3
Ver solución Código 21615
[Channel %1: ] Axis %2 taken from traverse mode to follow-up mode
Ver solución Código 21616
[Channel %1: ] Block %2 overlaid motion active at transformation switchover
Ver solución Código 21617
[Channel %1: ] Block %2 transformation does not allow to traverse the pole
Ver solución Código 21618
[Channel %1: ] As from block %2 transformation active: overlaid motion too great
Ver solución Código 21619
[Channel %1: ] Block %2 transformation active: motion not possible
Ver solución Código 21620
[Channel %1: ] Axis %2 Emergency braking ramp activated
Ver solución Código 21650
[Channel %1: ] Axis %2 overlaid motion not allowed
Ver solución Código 21660
[Channel %1: ] Block %2 axis %3 conflict between SYNACT: $AA_OFF and CORROF
Ver solución Código 21665
[Channel %1: ] $AA_TOFF cleared
Ver solución Código 21670
[Channel %1: ] Block %2 illegal change of tool direction with $AA_TOFF active
Ver solución Código 21700
[Channel %1: ] Block %3 axis %2 touch probe already deflected, edge polarity not possible
Ver solución Código 21701
[Channel %1: ] Block %3 axis %2 measurement not possible
Ver solución Código 21702
[Channel %1: ] Block %3 axis %2 measurement aborted
Ver solución Código 21703
[Channel %1: ] Block %3 axis %2 touch probe not deflected, illegal edge polarity
Ver solución Código 21740
Output value at analog output no. %1 has been limited
Ver solución Código 21750
Error during output of cam switching signals via timer
Ver solución Código 21760
[Channel %1: ] Block %2 too many auxiliary functions programmed
Ver solución Código 21800
[Channel %1: ] Workpiece setpoint %2 reached
Ver solución Código 22000
[Channel %1: ] Block %3 spindle %2 gear stage change not possible
Ver solución Código 22005
[Channel %1: ] Spindle %2 selected gear stage %3 not installed
Ver solución Código 22010
[Channel %1: ] Block %3 spindle %2 actual gear stage differs from requested gear stage
Ver solución Código 22011
[Channel %1: ] Block %3 spindle %2 change to programmed gear stage not possible
Ver solución Código 22012
[Channel %1: ] Block %2 leading spindle %3 is in simulation.
Ver solución Código 22013
[Channel %1: ] Block %2 dependent spindle %3 is in simulation.
Ver solución Código 22014
[Channel %1: ] Block %2. The dynamics of leading spindle %3 and dependent spindle %4 is too variably
Ver solución Código 22015
[Channel %1: ] Block %2 following spindle %3 No dynamic response for supplementary motion
Ver solución Código 22016
[Channel %1: ] Block %2 following spindle %3 in the range of reduced acceleration capability
Ver solución Código 22018
[Channel %1: ] Block %2 following axis/spindle %3 time monitoring: 'Synchronism fine' not reached
Ver solución Código 22019
[Channel %1: ] Block %2 following axis/spindle %3 time monitoring: 'Synchronism coarse' not reached
Ver solución Código 22020
[Channel %1: ] Block %3 spindle %2 gear step change position not reached
Ver solución Código 22022
[Channel %1: ] Block %2 spindle %3 gear stage %4 is expected for axis mode.
Ver solución Código 22030
[Channel %1: ] Block %2 foll owing spindle %3 Impermissible programming
Ver solución Código 22033
[Channel %1: ] Block %2 Axis/spindle %3 'Correct synchronism' diagnostics %4
Ver solución Código 22034
[Channel %1: ] Block %2 followin g spindle %3 PLC signal 'Enable override' has been set.
Ver solución Código 22035
[Channel %1: ] Block %2 following axis/spindle %3 unable to determine the offset value (reason %4).
Ver solución Código 22036
[Channel %1: ] Block %2 Axis/spindle %3 Synchronism override not possible (reason %4)
Ver solución Código 22037
[Channel %1: ] Block %2 Axis/spindle %3 'Correct synchronism' is being ignored
Ver solución Código 22038
[Channel %1: ] Block %2 Axis/Spindle %3 'Delete synchronism override' is being ignored
Ver solución Código 22040
[Channel %1: ] Block %3 spindle %2 is not referenced with zero marker
Ver solución Código 22045
Block %2 spindle/axis %3 not available in channel %1 because active in channel %4
Ver solución Código 22050
[Channel %1: ] Block %3 spindle %2 no transition from speed control mode to position control mode
Ver solución Código 22051
[Channel %1: ] Block %3 spindle %2 reference mark not found
Ver solución Código 22052
[Channel %1: ] Block %3 spindle %2 no standstill on block change
Ver solución Código 22053
[Channel %1: ] Block %3 spindle %2 reference mode not supported
Ver solución Código 22054
[Channel %1: ] Block %3 spindle %2 improper punching signal
Ver solución Código 22055
[Channel %1: ] Block %3 spindle %2 configured positioning speed is too high
Ver solución Código 22057
[Channel %1: ] Block %2 for following spindle %3 coupling as leading spindle/axis already existing
Ver solución Código 22058
[Channel %1: ] Block %2 for leading spindle %3 coupling as following spindle/axis already existing
Ver solución Código 22060
[Channel %1: ] Position control expected for axis/spindle %2
Ver solución Código 22062
[Channel %1: ] Axis %2 reference point approach: zero marker search velocity (MD) is not reached
Ver solución Código 22064
[Channel %1: ] Axis %2 reference point approach: zero marker search velocity (MD) is too high
Ver solución Código 22065
[Channel %1: ] Tool management: Tool motion is not possible as tool %2 is not in magazine %4.
Ver solución Código 22066
[Channel %1: ] Tool management: Tool change is not possible as tool %2 is not in magazine %4.
Ver solución Código 22067
[Channel %1: ] Tool management: tool change not possible since there is no tool available in tool group %2
Ver solución Código 22068
[Channel %1: ] Block %2 tool management: no tool available in tool group %3
Ver solución Código 22069
[Channel %1: ] Block %2 tool management: No tool available in tool group %3, program %4
Ver solución Código 22070
[TO unit %1: ] Please change tool %2 into magazine. Repeat data backup
Ver solución Código 22071
[TO unit %1: ] Tool %2 is active, but not in the magazine area under consideration
Ver solución Código 22100
[Channel %1: ] Block %3 spindle %2 chuck speed exceeded
Ver solución Código 22101
[Channel %1: ] Block %3 spindle %2 maximum speed for encoder resynchronization exceeded
Ver solución Código 22150
[Channel %1: ] Block %3 spindle %2 maximum speed for position control exceeded
Ver solución Código 22200
[Channel %1: ] Spindle %2 axis stopped during tapping
Ver solución Código 22250
[Channel %1: ] Spindle %2 axis stopped during thread cutting
Ver solución Código 22260
[Channel %1: ] Spindle %2 thread might be damaged
Ver solución Código 22270
[Channel %1: ] Block %2 maximum tapping speed reached
Ver solución Código 22275
[Channel %1: ] Block %2 zero velocity of thread axis at position %3 reached
Ver solución Código 22280
[Channel %1: ] In block %2: Prog. acceleration path too short %3, %4 required
Ver solución Código 22290
[Channel %1: ] Spindle operation for transformed spindle/axis %2 not possible (reason: error code %3).
Ver solución Código 22295
Channel %1 Spindle %2 DBB30 function not possible (cause: error code %3)
Ver solución Código 22296
Channel %1 Spindle %2 Error on gear stage change (cause: error code %3)
Ver solución Código 22297
Channel %1 Spindle %2 FC18 function not possible (cause: error code %3)
Ver solución Código 22320
[Channel %1: ] Block %2 PUTFTOCF command could not be transferred
Ver solución Código 22321
[Channel %1: ] Axis %2 PRESET not allowed during traverse motion
Ver solución Código 22322
[Channel %1: ] Axis %2 PRESET: illegal value
Ver solución Código 22400
[Channel %1: ] Option 'contour handwheel' not set
Ver solución Código 25000
Axis %1 hardware fault of active encoder
Ver solución Código 25001
Axis %1 hardware fault of passive encoder
Ver solución Código 25010
Axis %1 pollution of measuring system
Ver solución Código 25011
Axis %1 pollution of passive encoder
Ver solución Código 25020
Axis %1 zero mark monitoring of active encoder
Ver solución Código 25021
Axis %1 zero mark moni toring of passive encoder
Ver solución Código 25022
Axis %1 encoder %2 warning %3
Ver solución Código 25030
Axis %1 actual velocity alarm limit
Ver solución Código 25031
Axis %1 actual velocity warning limit
Ver solución Código 25040
Axis %1 standstill monitoring
Ver solución Código 25042
Axis %1 standstill monitori ng during torque/force limitation
Ver solución Código 25050
Axis %1 contour monitoring
Ver solución