Siemens SINUMERIK 840D CNC 錯誤代碼

[Channel %1: ] Block %2 following axis/spindle %3 status %4 impermissible traversing instruction

[Channel %1: ] Block %2 following axis/spindle %4 instruction %3 programmed repeatedly

[Channel %1: ] Block %2 following axis/spindle %3 CPFPOS not permitted (reason %4)

[Channel %1: ] Block %2 following axis/spindle %3 instructions %4 are not possible.

[Channel %1: ] Block %2 following axis/spindle %3 instructions %4 are not possible separately.

[Channel %1: ] Block %2 following axis/spindle %3 instructions %4 are not possible separately.

[Channel %1: ] Block %2 following axis/spindle %3 type of coupling/instruction %4 is not possible.

[Channel %1: ] Block %2 following axis/spindle %3 type of coupling/instruction %4 is not possible.

[Channel %1: ] Block %2 following axis/spindle %3 coupling type %4 maximum number of master values exceeded

[Channel %1: ] Block %2 following axis/spindle %3 coupling type %4 maximum number of master values exceeded

[Channel %1: ] Block %2 following axis/spindle %3 changing the reference system %4 is not possible.

[Channel %1: ] Block %2 following axis/spindle %3 changing the reference system %4 is not possible.

[Channel %1: ] Block %2 following axis/spindle %3 maximum number of couplings in the block %4 has been exceeded

[Channel %1: ] Block %2 following axis/spindle %3 status/instruction %4 is not possible.

[Channel %1: ] Block %2 following axis/spindle %3 status/instruction %4 is not possible.

[Channel %1: ] Block %2 following axis/spindle %3 coupling has not been defined.

[Channel %1: ] Block %2 following axis/spindle %3 coupling has not been defined.

[Channel %1: ] Block %2 following axis/spindle %3 leading axis/spindle %4 has not been defined.

[Channel %1: ] Block %2 following axis/spindle %3 leading axis/spindle %4 has not been defined.

[Channel %1: ] Block %2 axis %3 invalid feed type

[Channel %1: ] Block %2 axis %3 master spindle not programmed

[Channel %1: ] Block %2 axis %3 spindle not in standstill

[Channel %1: ] Block %2 axis %3 thread pitch is zero

[Channel %1: ] Block %2 axis %3 wrong parameter

[Channel %1: ] Block %2 no geometry axis programmed

[Channel %1: ] Block %2 spindle %3 selected gear stage %4 not installed

[Channel %1: ] Block %2 spindle %3 inserted gear stage %4 for tapping not installed

[Channel %1: ] Block %2 spindle %3 gear stage %4 expected

[Channel %1: ] Block %2 axis %3 SPCON not programmed

[Channel %1: ] Block %2 spindle/axis %3 SPCOF not executable

[Channel %1: ] Block %2 no stop required

[Channel %1: ] Block %2 for following spindle %3 coupling as leading spindle/axis already existing

[Channel %1: ] Block %2 for leading spindle %3 coupling as following spindle/axis already existing

[Channel %1: ] Block %2 axis %3 S value missing

[Channel %1: ] Block %2 axis/spindle %3 not programmable in the channel

[Channel %1: ] Block %2 spindle %3 thread function is active

[Channel %1: ] Block %2 axis %3 programmed speed is illegal (zero or negative)

[Channel %1: ] Block %2 axis %3 no measuring system available

[Channel %1: ] Block %3 following axis %2 overlaid movement not enabled

[Channel %1: ] Block %2 axis %3 is the slave axis, the coupling is being opened

[Channel %1: ] Axis %2 is the follow ing axis. The axis/spindle disables of leading axes %3 and %4 differ from one another.

[Channel %1: ] Synchronization aborted for slave axis/spindle %2

[Channel %1: ] Block %2 curve table %3 does not exist for axis %4

[Channel %1: ] Block %2 coupling: following axis %3 for lead axis %4 not available

[Channel %1: ] Block %2 coupling: Ring coupling at following axis %3 and leading axis %4 impermissible

[Channel %1: ] Block %2 coupling: too many couplings for axis %3, see active leading axis %4

[Channel %1: ] Block %2 fo llowing spindle/axis missing

[Channel %1: ] Block %2 m aster spindle/axis missing

[Channel %1: ] Block %2 followin g spindle/axis %3 not available

[Channel %1: ] Block %2 master spindle/axis %3 not available

[Channel %1: ] Block %2 identical spindles/axes %3

[Channel %1: ] Block %2 coupling to master spindle %3 already exists

[Channel %1: ] Block %2 coupling parameter not changeable

[Channel %1: ] Block %2 cyclic coupling

[Channel %1: ] Block %2 multiple link

[Channel %1: ] Block %2 Pa rameter is zero or missing

[Channel %1: ] Block %2 parameter is not relevant

[Channel %1: ] Block %2 too many couplings for axis/spindle %3

[Channel %1: ] Block %2 coupling of axis %3 prohibits transformation change

[Channel %1: ] Block %2 coupling of axis/spindle %3 prohibits reference point approach

[Channel %1: ] Block %2 string cannot be interpreted

[Channel %1: ] Block %2 coupling not defined

[Channel %1: ] Block %2 coupling is active

[Channel %1: ] Block %2 axis %3 is following axis and prohibits axis container rotation

[Channel %1: ] Block %2 axis %3 is master axis and prohibits axis container rotation

[Channel %1: ] Block %2 traverse instruction DC/CDC for axis %3 not allowed

[Channel %1: ] Block %2 traverse instruction ACP for axis %3 not allowed

[Channel %1: ] Block %2 traverse instruction ACN for axis %3 not allowed

[Channel %1: ] Block %2 incorrect position programmed for axis/spindle %3

[Channel %1: ] Program control: action %2<ALNX> not allowed in the current state

[Channel %1: ] Program control: action %2<ALNX> not allowed in the current state

[Channel %1: ] Program control: action %2<ALNX> not allowed

[Channel %1: ] Program control: action %2<ALNX> is aborted due to an alarm

[Channel %1: ] Action %2<ALNX> only possible in stop state

[Channel %1: ] Action %2<ALNX> only possible in reset state or at the block end

[Channel %1: ] Action %2<ALNX> not allowed in current mode

[Channel %1: ] Mode change is not allowed

[Channel %1: ] Program control: action %2<ALNX> only possible in reset state

[Mode group %1: ] [Channel %2: ] Mode change: action %3<ALNX> not allowed

[Mode group %1: ] [Channel %2: ] Mode change: action %3<ALNX> not allowed

[Channel %1: ] Action %2<ALNX> not allowed in the current block

[Channel %1: ] Repositioning: action %2<ALNX> not allowed in the current state

[Channel %1: ] For action %2<ALNX> all channels must be in reset state

[Channel %1: ] Action %2<ALNX> is not allowed due to a pending alarm

[Channel %1: ] Action %2<ALNX> is already active

[Mode group %2: ] [Channel %1: ] Machine data: channel/mode group assignment not allowed or assigned twice

[Channel %1: ] Subprograms: acti on %2<ALNX> maximum nesting depth exceeded

[Channel %1: ] Program control: action %2<ALNX> not allowed in the current state

[Channel %1: ] Caution: program test modifies tool management data

[Channel %1: ] Program control: action %2<ALNX> not allowed in the current state, action %3<ALNX> active

[Channel %1: ] Channel coordination: action %2 not allowed in block %3, marker %4 is already set

[Channel %1: ] Action %2<ALNX> at active interrupt treatment not allowed

[Channel %1: ] Interrupt treatment: action %2<ALNX> not possible

[Channel %1: ] Preceding block and current block %2 must be separated through an executable block

[Channel %1: ] Subprograms: acti on %2<ALNX> maximum nesting depth exceeded

[Channel %1: ] Conflict when activating user data type %2

[Channel %1: ] Interrupt treatment: action %2<ALNX> not allowed in the current state

[Channel %1: ] Interrupt treatment: action %2<ALNX> not possible due to stop

[Channel %1: ] Action %2<ALNX> not possible due to search run

[Channel %1: ] Action %2<ALNX> not possible due to active dry run

[Channel %1: ] Action %2<ALNX> not possible due to program test

[Channel %1: ] Action %2<ALNX> aborted due to active gear change

[Channel %1: ] Action %2<ALNX> rejected due to active gear change

[Channel %1: ] Action %2<ALNX> wait for gear change

[Channel %1: ] Action %2<ALNX> rejected because no program event has been executed yet

[Channel %1: ] Start program command action %2<ALNX> not possible

[Channel %1: ] Action %2<A LNX> not possible due to ASUP

[Channel %1: ] Action %2<ALNX> not possible due to active search blocks

[Channel %1: ] Action %2<ALNX> delayed up to the block end

[Channel %1: ] Start via START is not allowed

[Channel %1: ] Start via PLC is not allowed

Channel %1 dependent channel %2 still active

Correspondence between marker of channel %1 and channel %2 is invalid.

[Channel %1: ] Search run with hold block

[Channel %1: ] Search run in a protected program section.

[Channel %1: ] Start program command not possible due to MDI

[Channel %1: ] For slave axis %2 SERUPRO not allowed, as master axis %3 not subject to axis/spindle disable

[Channel %1: ] Block %2 programmed stop prohibited in stop delay area

[Channel %1: ] Stop in stop delay area is delayed

[Channel %1: ] Program %2 cannot be started due to global start disable.

[Channel %1: ] Stop-Delay area is suppressed

[Channel %1: ] Action %2<ALNX> prohibited during simulation block search.

[Channel %1: ] Ac tion %2<ALNX> prohi bited during EXECUTE PROGRAM AREA.

[Channel %1: ] Action %2<ALNX> prohibited during syntax check.

[Channel %1: ] NCK computing time reduced, start is not allowed.

[Channel %1: ] Block %2 maximum number of symbols exceeded

[Channel %1: ] Block %2 no memory left for tool/magazine data

[Channel %1: ] Block %2 no memory left

[Channel %1: ] Block %2 incorrect value for parameter %3

[Channel %1: ] Block %2 illegal array index 1

[Channel %1: ] Block %2 illegal array index 2

[Channel %1: ] Block %2 illegal array index 1

[Channel %1: ] Block %2 illegal axis index

[Channel %1: ] Block %2 illegal value

[Channel %1: ] Block %2 GUD variable not existing

[Channel %1: ] Block %2 requested data area too large

[Channel %1: ] Block %2 data is write-protected

[Channel %1: ] Block %2 %3 value below lower limit

[Channel %1: ] Block %2 %3 value exceeds upper limit

[Channel %1: ] Block %2 invalid value

[Channel %1: ] Block %2 digital i nput/comparator no. %3 not activated

[Channel %1: ] Block %2 digi tal output no. %3 not activated

[Channel %1: ] Block %2 analog input no. %3 not activated

[Channel %1: ] Block %2 analog output no. %3 not activated

[Channel %1: ] Block %2 NCK output %3 is assigned to a function via machine data

[Channel %1: ] Block %2 maximum of %3 NCK outputs programmable in the block

[Channel %1: ] Block %2 no tool selected

[Channel %1: ] Block %2 number of symbols too large

[Channel %1: ] Block %2 illegal D number

[Channel %1: ] Block %2 T no.= %3, D no.= %4 not existing

[Channel %1: ] Block %2 illegal sum correction number

[Channel %1: ] Block %2 H number al ready available in T no.= %3, D no.= %4

[Channel %1: ] D number %2 defined in tool T no. %3 and %4

[Channel %1: ] D number %2 of tools defined on magazine/location %3 and %4

[Channel %1: ] Block %2 illegal T number %3

[Channel %1: ] Block %2 T= %3 not existing, program %4

[TO unit %1: ] Invalid tool designa tion of '%2', duplo no. %3. No more replacement tools possible in '%4'.

[Channel %1: ] Block %2 the acti ve tool is no longer on toolholder no./spindle no. %3, program %4

[Channel %1: ] Block %2 no suitable tool found

Channel %1 block %2 illegal tool holder number %3

[Channel %1: ] Block %2: Data of tool %3 cannot be deleted.

[Channel %1: ] Block %2 deleting magazine data not possible

[Channel %1: ] Block %2 access to variable not possible

[Channel %1: ] Tool management: Load manual tool %3, duplo no. %2 onto spindle/toolholder %4

[Channel %1: ] Tool management: remove manual tool %3 from spindle/toolholder %2

[Channel %1: ] Remove manual tool from toolholder %4 and load manual tool %3 %2

[Channel %1: ] Block %2 tool not existing

[Channel %1: ] Block %2 tool T/D= %3 - tool type %4 is not permitted

[Channel %1: ] Block %2 Duplo no. already assigned

[Channel %1: ] Block %2 illegal tool definition

[Channel %1: ] Block %2 illegal magazine definition

[Channel %1: ] Block %2 illegal magazine location definition

[Channel %1: ] Block %2 illegal tool adapter operation

[Channel %1: ] Block %2 call-by-reference: illegal variable

[Channel %1: ] Block %2 axis %3 is not an indexing axis

[Channel %1: ] Block %2 indexing axis %3 with Hirth tool system is active

[Channel %1: ] Block %2 indexing axis %3 with Hirth tooth system stop is delayed

[Channel %1: ] Block %2 indexing axis %3 with Hirth tooth system and axis not referenced

[Channel %1: ] Block %2 invalid index for indexing axis %3

[Channel %1: ] Block %2 preset on transformed axis %3 not possible

[Channel %1: ] Block %2 axis %3 transformation active: inhibits rotation of axis container

[Channel %1: ] Block %2 axis %3 in volved in the transformation, action cannot be carried out

[Channel %1: ] Block %2 approaching fixed point for transformed axis %3 not possible

[Channel %1: ] Block %2 referencing for transformed axis %3 not possible

[Channel %1: ] Block %2 spindle operation for transformed axis %3 not possible

[Channel %1: ] Block %2 machine axis %3 not programmable

[Channel %1: ] Block %2 illegally coded position programmed

[Channel %1: ] Axis %2 not referenced

[Channel %1: ] Fixed-point approach not possible for axis %2 in JOG, reason %3

[Channel %1: ] Axis %2 fixed-point approach in JOG: Fixed point %3 changed

[Channel %1: ] Axis %2 fixed-point approach in JOG and override motion active

[Channel %1: ] Axis %2 fixed-point position not available

Indexing axis %1 fixed point %2 unequal indexing position

[Channel %1: ] JOG to position not possible for axis %2, reason %3

[Channel %1: ] Axis %2 JOG to position and override motion active

[Channel %1: ] Axis %2 JOG to position: Position changed

[Channel %1: ] Axis %2 JOG to position deactivated

Indexing axis %1 $SA_JOG_POSI TION unequal indexing position

[Channel %1: ] JOG in a circle is activated, but the axis %2 required for this is not a geometry axis.

[Channel %1: ] JOG a circle is not possible, reason %2