Back to all Chiron models Search all database
Chiron Siemens-Control CNC
Chiron Siemens-Control CNC Error Codes
Complete alarm and error code reference for the Chiron Siemens-Control CNC. Browse all 545 documented fault codes below, each linking to a detailed troubleshooting guide.
Search this section
Search Chiron Siemens-Control CNC
Search all 545 Chiron Siemens-Control CNC codes without changing pages.
Complete Alarm List (Page 2 of 3)
Code 700022
PLC-MD wrong (cooling unit 1)
View solution Code 700312
PLC-MD wrong (cooling unit 2)
View solution Code 700024
PLC-MD wrong (coolant)
View solution Code 510116
RSF60 filter dirty
View solution Code 700136
Chip conveyor not selected
View solution Code 700412
Chip spiral not selected
View solution Code 700709
Error coolant flow monitor high pressure (1))
View solution Code 700710
Error coolant flow monitor high pressure (2))
View solution Code 700708
Fault flow monitor coolant low pressure
View solution Code 700712
Error flow monitor rinse fixture (1)
View solution Code 701020
Error flow monitor rinse fixture (2)
View solution Code 700711
Error flow monitor bed rinsing
View solution Code 510123
Moisture sensor mainspindle (broken cable) (1)
View solution Code 700448
Failure main spindle moisture sensor (cable damage) (2)
View solution Code 700215
Failure coolant system
View solution Code 700211
Error chip spiral
View solution Code 700417
Error chip spiral
View solution Code 701745
Time monitoring max. paper filter coolant level
View solution Code 701741
Time monitoring transport paper filter
View solution Code 701748
Coolant filter monitoring
View solution Code 700461
Fire protection door not closed
View solution Code 700460
Fire protection door not open
View solution Code 700428
PLC-MD incorrect (fire protection door)
View solution Code 700427
Sensor monitoring! Fire protection door open/closed
View solution Code 701028
Battery alarm, probe (tool revolver)
View solution Code 510104
Probe battery alarm
View solution Code 700322
Probe battery alarm
View solution Code 700107
Probe dirty
View solution Code 701025
Probe in tool revolver! No speed or coolant possible
View solution Code 510101
Probe in spindle! No spindle rotation or coolant possible.
View solution Code 700105
Probe not switched on (table probe)
View solution Code 701027
Probe not in tool revolver!
View solution Code 510103
Probe not in spindle
View solution Code 700030
PLC-MD wrong (probe )
View solution Code 510102
Probe malfunction (spindle probe)
View solution Code 700106
Probe malfunction (table probe)
View solution Code 700113
Faulty probe (tool changer)
View solution Code 701440
Min. lubrication not selected
View solution Code 701441
Minimal lubrication: Flow monitor
View solution Code 701403
PLC_MD_wrong (tool arms min. lubrication)
View solution Code 701402
Malfunction minimum lubrication
View solution Code 701456
Warning minimum lubrication
View solution Code 700056
Asup-initialising start up not finished
View solution Code 700414
Operating mode can only be changed in RESET state
View solution Code 700326
Wrong cycle in the machine ! (SYNCR: version >14.01 neces- sary)
View solution Code 701850
Wrong search target in block search (tool call)
View solution Code 701623
Error in NC program! Different T-output (background magazine)
View solution Code 700011
Wrong program # identified
View solution Code 700111
Fault during loading variables (FB2 in FB113)
View solution Code 700148
Program number selection 1 activated
View solution Code 700149
Program number selection 2 activated
View solution Code 700147
Program number selection is being edited: NC start not possible.
View solution Code 700411
Program number selection not selected
View solution Code 700009
Selected program # disabled
View solution Code 700255
Workpiece machined with new tool
View solution Code 702307
Profibus error Slave 10 (installation - tool magazine)
View solution Code 702308
Profibus error Slave 11 (coolant system)
View solution Code 702309
Profibus error Slave 12 (options)
View solution Code 702310
Profibus error Slave 13 (hydraulic unit - clamping device)
View solution Code 702311
Profibus error Slave 14 (hydraulic unit)
View solution Code 702312
Profibus error Slave 15 (hydraulic unit)
View solution Code 702313
Profibus error Slave 16 (electric cabinet - loader - DP/DP coupler)
View solution Code 702314
Profibus error Slave 17 (automatic protective door - motor)
View solution Code 702315
Profibus error Slave 18 (basket changer)
View solution Code 702316
Profibus error Slave 19 (basket changer /TBZ column)
View solution Code 702318
Profibus error Slave 21 (coolant system - variovalve)
View solution Code 702320
Profibus slave 23 malfunction (process monitoring system)
View solution Code 702321
Profibus slave 24 malfunction (process monitoring system 2)
View solution Code 702323
Profibus error Slave 26 (electric cabinet - loader - hardware)
View solution Code 702326
Profibus error Slave 29 (tool identification system)
View solution Code 702300
Profibus error Slave 3 (electric cabinet)
View solution Code 702301
Profibus error Slave 4 (pneumatic plate - pneumatics)
View solution Code 702302
Profibus error Slave 5 (pneumatic plate - clamping device)
View solution Code 702303
Profibus error Slave 6 (pneumatic plate - automatic protective door)
View solution Code 702304
Profibus error Slave 7 (machine component)
View solution Code 702305
Profibus error Slave 8 (machine component - Lubrix)
View solution Code 702306
Profibus error Slave 9 (installation - tool magazine)
View solution Code 510008
Side door not closed
View solution Code 700153
Tool loading door not closed
View solution Code 700015
Bypass prot.door monitoring
View solution Code 701758
Drive protective doors: Parameterisation error"
View solution Code 701757
Drive protective doors not ready for operation
View solution Code 700157
Safety pressure switch protective doors
View solution Code 700123
Check limit switch or locking magnets of protect. doors
View solution Code 700124
Check test signal of protect. doors
View solution Code 700156
Enable protective doors missing
View solution Code 701543
Safety device loader not closed
View solution Code 701755
Protective doors not released
View solution Code 701953
Protective equipment not OK (background magazine)
View solution Code 701754
Protective doors not locked
View solution Code 700048
Not possible to unlock protective door! Spindles/axes not at standstill
View solution Code 701429
Opening of protective door only possible with channel reset (turning mode)
View solution Code 702532
Protective door not referenced!à Open/close protective door with button
View solution Code 700155
Protective door(s) not closed
View solution Code 700154
Protective door(s) not open
View solution Code 700158
Bypass protective doors (service)
View solution Code 701760
Drive protective doors: over-current, time-out
View solution Code 510100
No spindle speed, coolant or tool change possible in service mode
View solution Code 702713
Safety: No operating mode selected
View solution Code 701261
No acknowledgement mode possible in mode 1
View solution Code 700004
EMERGENCY STOP button
View solution Code 702701
Safety: PLC-MD wrong (protective door configuration)
View solution Code 702700
Safety: PLC-MD wrong (table type configuration)
View solution Code 702706
Safety: Test stop, switch to JOG mode
View solution Code 702753
Safety: Test stop running
View solution Code 702704
Safety: Test stop requested
View solution Code 702708
Safety: Test stop, switch operating mode selection switch to zero position
View solution Code 702707
Safety: Test stop, close protective door
View solution Code 702710
Safety: Test stop, clamp clamping device or deactivate
View solution Code 702705
Safety: Switch the feed correction switch to 100%
View solution Code 700014
Operator push button pressed too long (2 min.)
View solution Code 702714
Safety: Loading door safety relay monitoring
View solution Code 702711
Safety: EMERGENCY STOP safety relay monitoring
View solution Code 702712
Safety: Protective door safety relay monitoring
View solution Code 702715
Safety: Drive power supply contactor monitoring
View solution Code 702716
Safety: Tool changer door safety relay monitoring
View solution Code 700132
Control not switched on
View solution Code 701430
Caution - turning tool in the spindle! No speed possible..
View solution Code 700738
Caution: moving in the swung system
View solution Code 510006
Swivel head brake not actuated
View solution Code 700746
Turning has not been deactivated --> Switch off main switch
View solution Code 601109
Swivel head not clamped
View solution Code 601110
Swivel head not released
View solution Code 700740
Swivel head not in position (0°)
View solution Code 700104
Run time hydraulic exceeded
View solution Code 700025
PLC-MD wrong (clamping device)
View solution Code 701446
Clamping fixture not selected
View solution Code 700051
Clamping device not clamped
View solution Code 702804
System pressure, tool clamping hydraulics, missing (running time monitoring)
View solution Code 700102
Clamping hydraulics temperature monitoring
View solution Code 702802
Temperature monitoring, tool clamping hydraulics
View solution Code 701107
Workpiece clamping pressure (1) too high! Rotary table speed > 200 rpm disabled
View solution Code 701108
Workpiece clamping pressure (2) too high! Rotary table speed > 200 rpm disabled
View solution Code 700103
Minimum oil level of clamping hydraulics
View solution Code 702803
Min. oil level, tool clamping hydraulics
View solution Code 700108
Monitoring of clamping hydraulics filter
View solution Code 700058
Spindle quad-rings not sealed
View solution Code 700059
Spindle quad-rings not released
View solution Code 700145
Main spindle speed control
View solution Code 700247
Wrong tool in the spindle
View solution Code 700142
fault star-delta change over
View solution Code 703160
Main spindle and amplification motor, main spindle, not engaged (NC)
View solution Code 700023
PLC-MD wrong (spindle quad rings)
View solution Code 701509
PLC-MD wrong: Activation of spindle type / warm-up cycle
View solution Code 701231
PLC-MD incorrect (VPM - voltage protection module)
View solution Code 700249
No standstill main spindle (1)
View solution Code 700449
No standstill main spindle (2)
View solution Code 700251
Main spindle not in position (1)
View solution Code 700451
Main spindle not in position (2)
View solution Code 700250
Main spindle standstill (1)
View solution Code 700450
Main spindle standstill (2)
View solution Code 700258
Spindle warm-up mode active (please wait)
View solution Code 700256
Spindle warm-up active: coolant medium / spindle bearings (please wait)
View solution Code 701262
Temperature monitoring VPM
View solution Code 703161
Amplification motor, main spindle is not engaged
View solution Code 703162
Amplification motor, main spindle, not disengaged
View solution Code 703163
Amplification motor, main spindle is not in position for engaging/disengaging
View solution Code 702509
Amplification motor, main spindle: Learn sensors for coupling
View solution Code 701532
Warm-up cycle spindle necessary! Start cycle with <Jog> and <Spindle Start> key
View solution Code 701535
Tool suitable for spindle speed in warm-up cycle? Yes, continue with <Cycle Start> + <Feed Start>
View solution Code 702512
Overtemperature, motor/drive, SP1V spindle (amplification motor, main spindle)
View solution Code 700401
Switch off main switch (coupling triggered)
View solution Code 700747
Power failure: Shut off main switch
View solution Code 700047
>Cycle Stop< key pressed
View solution Code 702908
Feed Stop M00/M01
View solution Code 700159
Feedrate switch at 0
View solution Code 700006
Bimetals tripped
View solution Code 703105
PLC MD incorrect! (Tool identification system)
View solution Code 703104
Sensor monitoring! Tool identification system: Home position/ working position
View solution Code 703140
Tool identification system not in working position
View solution Code 703139
Tool identification system not in home position
View solution Code 701936
Tool ID system: Code carrier not available
View solution Code 701932
Tool ID system: Data read/write error
View solution Code 701937
Tool ID system: Read tools in the background magazine running
View solution Code 701933
Tool ID system: Data comparison error! Tool management <> Code carrier
View solution Code 700055
Pm required
View solution Code 701563
12000 h maintenance not performed
View solution Code 701560
2000 h maintenance not performed
View solution Code 701561
6000 h maintenance not performed
View solution Code 700112
Pm not done
View solution Code 701562
Prepare for 12000h maintenance
View solution Code 701558
Prepare for 2000h maintenance
View solution Code 701559
Prepare for 6000h maintenance
View solution Code 700054
Prepare for pm
View solution Code 700233
Fault data transmission for tool management
View solution Code 700216
Fault length 1 cutting edge 1
View solution Code 700218
Fault length 1 cutting edge 2
View solution Code 700217
Fault radius cutting edge 1
View solution Code 700219
Fault radius cutting edge 2
View solution Code 700031
Tool live management error (Siemens)
View solution Code 700263
Main spindle clamped without tool (1)
View solution Code 700463
Main spindle clamped without tool (2)
View solution Code 702559
Main spindle clamped without tool (3)
View solution Code 702560
Main spindle clamped without tool (4)
View solution Code 700222
No tool found
View solution Code 700221
Tool management enable missing
View solution Code 700026
PLC-MD wrong (qty. of tools)
View solution Code 702217
System error tool management SIEMENS! T preselection <> T output
View solution Code 510125
Incorrect tool # selected
View solution Code 700234
Pre-warning tool life
View solution